Insignia KYS900 User manual

Installation Guide
KYS900 Sauna

IMPORTANT : Please check all contents before build commences. No returns
will be accepted once the build has started as it is deemed acceptance of
product.
30 Day Technical Support : Please call 01908 317512 and request technical
support for assistance during your build, should you require it.
Replacement Parts : To request replacement parts covered under your
warranty, please visit insigniashowers.com. Click Support and make a
warranty request.
Spare Parts : For spare and replacement parts outside of your warranty
period, please visit insigniashowers.com/replacement-parts.html.
INSIGNIA INSTALLATION GUIDE
KYS900 Sauna

04
05
06
14
15
18
19
23
24
25
27
28
Electrical & Tool Requirements
Box Contents
Assembly of the Exterior
Assembly of the Roof
Installation of Door
Fitting the Sauna Heaters
Installing Accessories
Water Valve Connections
Power Connections
Control Panel Instructions
Sauna Safety Instructions
WEEE Compliance
Thank you for your recent purchase of an Insignia product. Please
read this guide with great care to ensure you get the best out of
your build and have a nished product that will last for many years
to come.
Contents

Electrical & Tool Requirements
Electrical Requirement
Voltage Rating : 220 - 240AC
Frequency Rating : 50Hz
Power Rating : 2500 Watts
Amperage : 10.42 Amps
Always consult a qualied Electrician before connection to ensure suitability. Your
electrical contractor will understand ALL legal requirements of connection before
undertaking any work or installation.
UNDER NO CIRCUMSTANCES UNDERTAKE THIS YOURSELF WITHOUT CONSULTATION
Note for Electrician : This product comes with pre-tted RCD unit. We leave it this
way for you to connect it your own way due to continued additions to current
regulations.
• Connect within current laws and IP directives. Subject to room location.
• (Preferred) Wire into isolated fused feed connecting directly to the house
consumer/service box.
Always use protection against electrical surge. Your shower should be treated the
same as a home computer. A surge protector should eradicate the possibility of
either the transformer or control panel being burnt out.
Subject to connection type, electrical work needs to be signed off by a fully
qualied operative by law. Failure to adhere to this will not only void your electrical
warranty for your sauna, but could void your house insurance.
Required Tools
Scissors
Knife
Spirit Level
Tape Measure
Philips Screwdriver
Electric Drill
Safety Gloves & Glasses
Recommended minimum 2 person installation.

IMPORTANT : Have you got everything? If not please contact the Insignia
directly on 01908 317 512.
Remember to never book your tradesman until everything has arrived,
been checked and is present.
No replacement/missing parts can be obtained free of charge during
or after the build. Any claims can only be within the timescale permitted
(48 hours after delivery) and always before the build.
Box Contents
Box Contents Check List
Heater Quantity 3 [ ]
Heater Covers Quantity 3 [ ]
Column Quantity 1 [ ]
Corner posts Quantity 4 [ ]
Stool Quantity 1 [ ]
Hand Shower + Riser Rail Quantity 1 [ ]
Glass Shelf Quantity 1 [ ]
Mirror Quantity 1 [ ]
Tray Quantity 1 [ ]
Roof Quantity 1 [ ]
Back Glass Panel Quantity 2 [ ]
Front Fixed Glass Quantity 1 [ ]
Side Panel Quantity 2 [ ]
Door Quantity 1 [ ]
Screw Pack Quantity 1 [ ]

Step 1 :
Levelling the Tray
Note
Level the tray by using a spirit level and then
changing the elvation of the legs by screwing
clockwise or counter-clockwise
Visit insigniashowers.com for all your accessories and upgrades.

Connecting the Column and Glass Panel Brackets
Step 2 :
Note
Take the glass brackets and connect to the tray, with the
screw tightening connection facing inside the tray.
Locate the pre drilled holes for connection. Repeat for all
brackets.
Then take 90 degrees ‘L’ bracket and connect readt for
the column

Step 3 :
Installing the Column
Note
Take the rubber seal without holes and
place on the tray. Slot the column into
position, ensuring you connect all power
cables as ou alignthe column. Once aligned,
screw the column into the ‘L’ Bracket.

Call Insignia on 01908 317512 for any advice with installation.
Installing the Right Back Panel
Step 4 :
Note
Ensure you place a seal along he bottom of the glass
panel rst. Then simply slot the glass panel into the bracjet
and secure in place with the bolt.
Leave a gap at the end of the seal for the bracket to t.

Step 5 :
Installing the Right Back Panel Framework
Note
Between ALL glass and aluminum framework
connections, place a ribbed rubber seal
tightly to protect the glass and secure in
position.
Along the corner of the glass, place the 90
degree aluminium framework connector,
angled to allow the side panel to be inserted
along the right hand side of the shower.
Call Insignia on 01908 317512 for any advice with installation.

Step 6 :
Note
Ensure you place a seal along the bottom of the glass panel rst.
Then simply slot the glass panel into the bracket and secure in
place with the bolt. Also ensure you feed the panel into the 90
degree corner upright.
Once installed, slot in the seal to protect and secure.
Installing the Right Side Panel and Front Framework

Step 7 :
Installing the Front Fixed Glass
Note
Repeat the process from the previous pages.

Call Insignia on 01908 317512 for any advice with installation.
Installing the Left Back and Side Panels
Step 8 :
Note
Repeat the process from the previous pages

Step 9 :
Installing the Roof
Note
Place the rubber seal on the top of the
column before putting the roof in place. Use
the provided nuts, bolts and screws to secure
the roof.
Call Insignia on 01908 317512 for any advice with installation.

Installinig the Door Seal
Step 10 :
Note
Push the xed glass seal onto the xed glass.
Push the bottom door seal onto the door.
Push magnetic door seals on the door and xed glass
panel

Step 11 :
Installing the Door Hinges
Note
Use the Allen key provided to take the hinge
apart. Use glass protecting spacer either side
of the glass and connect the bolts from the
inside of the shower.
Lift the door into position and hold steady
whilst connecting the hinges. To align,
slacken off the hinge slightly, adjust the door
position and then retighten. Repeat the
process till the door shuts perfectly.

Call Insignia on 01908 317512 for any advice with installation.
Installing the Door Handle
Step 12 :
Note
Use the Allen key provided to take the door handle apart.
When connecting ensure you have the glass protecting
spacer on either side of the glass.

Note
Install all heater brackets with the hook on the inside of
the shower. ALWAYS facing upwards. Also use the round
glass prtectors over each bolt.
Step 13 :
Installing the Sauna Heaters
Note
Ensure each corner is sitting at 90 degrees
and slot the heater onto the brackets. Tap
the heater down with a mallet to lock them
into position. Ensure the connection wire is
fed up inside the heater for a ush t.
Call Insignia on 01908 317512 for any advice with installation.
Note
Connect the wires under the heaters. Feed the wire up
into the heater to ensure a ush tting on the next step.

Installing the Accessories
Step 14 :
Note
Using the accessories connection bolts, screw the acces-
sories in position and secure from the rear using washers
and nuts.

Installing the Accessories Continued
Note
Using the screws and nuts provided, connect
the shelf to the left back wall using the
screws and nuts.
Step 15 :