Operator's guide:
1)Unpacking instructions
2)The handles
3)Circular glass shelving
4)Grid shelves
5)Internal cleaning
6)External cleaning
7)Connection to the mains
8)Controls
9)Checking correct operation
10)Internal cleaning
11)Replacement of internal light bulbs
12)Replacement of the door's magnetic gasket
13)Replacement of a glass panel
2)Cleaning the evaporator
Maintenance manual (Page 48):
1)Cleaning the condenser
3)Wiring diagram diagram of refrigeration unit
!
I
UK
D
E
F
NL
P
S
DK
FIN
B
GR
CZ
EE
LV
LT
H
M
PL
SK
SLO
6
Operator's guide
WARNINGS
It is most important that this instruction booklet is kept together with the appliance both for future
reference and for reasons of safety.
1. Adults should operate this appliance only. Do not allow children to use the controls or play with it. 2
3
4
5
6
7
. It
is forbidden to modify in any way the main functions and characteristics of this appliance. . The electrical
installation of the appliance should be carried out by a qualified electrician or other competent person.
. Never attempt to carry out repairs unassisted. Inexpert repairs can cause serious damage and
malfunction. . Assistance has to be provided by an authorized engineer only. Always use original spare
parts. . This appliance is not suitable for the storage of basic commodities not including food-stuffs.
. The manufacturers of this appliance accept no responsibility for the consequences of misuse in
contravention of these safety instructions. It further reserves the right to carry out improvements without
prior notice.8 9
10
11
12
13
Our products are for internal use only –do not install outside restaurants, shops.
. Avoid installing the cabinet directly in line with sunlight. . Nevere install the appliance near
sources of heat, such as radiators, stoves, etc. . Keep the ventilation grills free from obstruction for at
least 30 cm. .Ensure that the products displayed on the shelves and grills do not hang over the edges.
. If damp air or products to be refrigerated should cause ice to form on the evaporator, we recommend
stopping the compressor and placing the goods in special refrigerated containers, kept at the same
temperature, until defrosting is completed;if this is not carried out the compressor will continue to operate
leading to a wasteful consumption of electricity and poor performance. . If the appliance is not working
and unused, it is indispensable to keep the door open at least 10 cm. Avoiding this, you will avoid also the
consequent mildew formation and unpleasant smells.
Cut surrounding tape. Remove the cardboard package by sliding it upwards.
Remove the nails from the wooden crate with care. Insert forks of forklift truck
between the appliance and pallet or crate. . Lift the appliance. . Remove the pallet or crate. . Place
the appliance on a flat, level surface. . Make sure there is nothing left in the package before disposing of
it. Sort out the packaging materials in order to facilitate disposal (see fig. 1).
The handles can be found in a bag inside the appliance. . Fix the base of the handle using the two
screws already inserted in the holes on the door post; wrench down the screws. Place the plastic insert
over the handle and press down until it clicks into place (see fig. 2).
,
These shelves, which can be found in the cardboard box, should be slid into the supports on the
special posts. Fit the bottom mirror shelf first. . Secure the shelves in place using the screws you will find
in the bag, with the plastic part facing the glass. Tighten with care (see fig. 3).
,
You will find the shelves in a bag inside the appliance. Fasten the shelves, by putting their hooks in
the slots on the posts and by pushing them downwards . The grills, which are in the cardboard
box, should be placed on the shelves, with the raised edge opposite to the doors (see fig. 4).
Clean the internal surfaces and glass panels with a soft sponge and a neutral detergent. Wipe with a
soft dry cloth.
Use the same products as used for the internal cleaning. . Remove the protection from the steel parts
of the panel and grills (see fig. 5).
. Ensure that mains voltage and frequency are the same as those stated on the rating plate attached
to the appliance. . Ensure that the supply socket:
. Ensure that there is no danger of explosion (AD) in the room. Make sure the environment is suitable
for the power supply cable provided. The cable of the appliance is H05 VVF, designed for internal use.
If the equipment has been transported or stored overturned, let is rest in its correct position for at
least 3 hours before hooking it up to the mains. . Insert the plug in the socket (do not use three-way
adapters and reduction adapters) (see fig. 6).
1. UNPACKING INSTRUCTIONS
CARDBOARD BOXES 1a.
WOODEN CRATES 1b. 2.
3 4 5
6
7.
2. THE HANDLES
1. 2
3.
3. CIRCULAR GLASS SHELVING
1.
2
4. GRID SHELVES
1. 2.
(B) (C). 3
5. INTERNAL CLEANING
1. 2.
6. EXTERNAL CLEANING
1. 2
7. CONNECTION TO THE MAINS
1 (A)
2
3 4.
N.B.:
5
SNELLÉ 750 RBT
SNELLÉ 750 BTV and 400 BTV
a) b)
c)
model
models
is properly earthed; fulfils the requirements of the
rated current as set out on the rating plate; complies with the IEC regulations:- thermal-magnetic
switch with In = rated value as stated on the rating plate; - differential with Id sensitivity = 30 mA.
!
