Techni Mobili RTA-S10 User manual

MODEL RTA-S10
English
MODEL RTA-S10
This product comes in 2 boxes.

RTA-S10
Product Size: 31.5"W x 15.75"D x 23"H
Shelves: 14.75"W x 14.25"D x 7.5" H
Drawers: 12.75"W x 13.25"D x 3.5"H
31.5"
15.75"
31.5"X15.75"X0.3"
Product Net Weight:70.55 lbs

RTA-S10 P.3
PARTS LIST
23
14
7
568
11
910 12
14 15
13 16
Left
Left Right
Right
118
13
10
8
Left Panel Middle Vertical Panel Casters Right Panel
Middle Horizontal Panel Bottom Panel Back Panel Top Wood Panel
Support Tubes Top Glass Drawer Left Panels Drawer Right Panels
Drawer Front Panel Drawer Bottom Panel Drawer Back Panel Sliders
x4
x4 x3 x3
x3 x3 x3
x3Sets

RTA-S10 P.4
18 19
17
SCREWS LIST
A
C
D
B
E
6X20 MM
6X25 MM
6X25 MM
6X40 MM
4
4
8
16
PART PARTQTY. QTY.ITEM ITEM
4X10 MM
4X30 MM
4X14 MM F
G
12
12
18
1
3X15 MM
H24
4X20 MM
I8
Handles Door Panel Hinges
Cam lock
Cam bolt
1. 2. 3.
Screw the bolt into the
corresponding panel.
In the other panel, insert
and align the cam lock.
Join the panels.
Turn the cam lock.
MISALIGNED:
TURN CAM LOCK
TO POINT TOWARDS
THE HOLE
CORRECT
HOW TO ASSEMBLE USING BOLTS AND CAM LOCKS:
If the panel already comes with the cam lock inserted, make sure is aligned:

RTA-S10 P.5

RTA-S10 P.6
1
ASSEMBLY STEPS:
SCREWS
16PCS
4X14 MM
A
34PCS
6
Use screws A to affix the Casters (3) to the bottom
surface of Bottom Panel (6). Make sure to place the
locking casters at the front.
SCREWS
H
12PCS
3X15 MM
2
24
16 16
Right
Left
3PCS 3PCS
Get all the Flat Sliders (16) and use screws H to assemble
them to the Middle Vertical Panel (2) and the Right Panel
(2 & 4) as shown. The wheel on the sliders go facing to the
FRONT and the screw goes on the hole after the wheel as
shown.
Please pay attention to the direction of the panels.
Note: The sliders will be
flushed at the front on
panels (2) and receded
5/8" on panels (4.)
SCREWS
2PCS
6X40 MM
B
3
2
5
First screw bolts B to the Middle Vertical Panel (2), then assemble
the Middle Horizontal Panel (5) to it as explained in page 4.
SCREWS
2PCS
6X40 MM
B
42
6
First screw bolts B to the Bottom Panel (6), then assemble
the Middle Vertical Panel (2) to it as explained in page 4.
Top side:
Back
Front

RTA-S10 P.7
SCREWS
6PCS
6X40 MM
B
5
6
1
4
2
5
First screw bolts B to the Left Panel (1) and Right Panel (4), then assemble the Middle
Horizontal Panel (5) and Bottom Panel (6) as shown and as explained in page 4.
67
7
SCREWS
2PCS
4X14 MM
A
7
rear side
Slide in the Back Panel (7).
Use screws A to assemble the
Back Panel (7) to the Middle
Vertical Panel (2).
8
SCREWS
6PCS
6X40 MM
B
8
12
4
First screw bolts B to the Top Wood Panel (8), then assemble it to the Left and Right
Panel, Middle Vertical Panel (1, 2 & 4) as shown and as explained in page 4.

RTA-S10 P.8
SCREWS
4PCS
6X20 MM
C
SCREWS
4PCS
6X25 MM
D
9
10
94PCS
10
8
10
Use screws C to assemble the Support Tubes (9)
to the Glass Top (10).
Use screws D to assemble the Support Tubes (9) to
the Top Wood Panel (8).
11
19
17
18 18
2PCS
12
SCREWS
4X20 MM
I
2PCS
SCREWS
E
4PCS
4X10 MM
Use screws I to assemble the Handle (17) to
the Door Panel (18). Use screws E to assemble the Hinges (19)
to the Door Panel (18).

RTA-S10 P.9
13
If the door does not close properly, you can adjust its position by unscrewing
loose the corresponding screws on the hinges:
Adjusts the door vertically
Adjusts the door
horizontally
Adjusts the door side-to-side
when it is closed.
When the optimal position has been reached, re-tighten the screws.
19 2PCS
18
SCREWS
E
4PCS
4X10 MM
Use screws E to assemble the
Hinges (19) to the Left Panel (1).

SCREWS
4PCS
6X25 MM
F
14
15
11
12
13
14
11
12
RTA-S10 P.10
First screw bolts F to the Drawer Front
Panel (13), then assemble the Drawer
Left & Right Panels (11 & 12) as explained
in page 5.
Slide in the Drawer Bottom Panel (14).
SCREWS
4PCS
4X30 MM
G
16
15 Use screws G to assemble
the Drawer Back Panel (15)
to the Drawer Left & Right
Panels (11 & 12).
SCREWS
H
4PCS
3X15 MM
17
16
16
Right Left
Place the drawer upside- down as shown and use screws H to
assemble the “L” shaped Sliders (16) to the Drawer Left & Right
Panels (11 &12) as shown.
IMPORTANT: REFER TO THE DRAWINGS FOR THE CORRECT
POSITION OF THE SLIDERS. If they get installed incorrectly,
the drawers will raise 1" with a gap at the bottom and the top
drawer will not close!
SCREWS
4X20 MM
I
2PCS
18
17
Use screws I to fix the Handle (17)
to the Drawer Front Panel (13).
REPEAT STEPS 14 THRU 18
FOR THE OTHER DRAWERS

RTA-S10 P.11
19
20
Tighten any and all screws.
Insert the drawers into the cabinet, starting with the bottom drawer.
You might have to insert it at a downward tilted angle.
Enjoy your unit!

English
- DO NOT EXPOSE THE SURFACES TO DIRECT SUNLIGHT OR EXTREME
ENVIRONMENTAL CONDITIONS. ANY DAMAGE RESULTING FROM SUCH
EXPOSURE IS NOT COVERED BY THE PRODUCT’S WARRANTY.
- THE PREFERABLE METHOD TO CLEAN THE SURFACES IS TO WIPE THEM
USING A SOFT CLOTH DAMPENED WITH A SOLUTION SOAP AND WATER,
THEN DRY WITH A CLEAN TOWEL.
- DO NOT SPRAY SOLVENTS OR CLEANING AGENTS DIRECTLY OVER THE
SURFACES, STRUCTURAL TUBES OR METAL PARTS.
- DO NOT LEAN, SEAT OR STAND OVER THE UNIT.
- DO NOT ALLOW CHILDREN TO PLAY OVER/UNDER THE UNIT, NOR ALLOW
THEM TO REACH INSIDE ANY COMPARTMENTS WITHOUT THE SUPERVISION
OF AN ADULT.
- BEFORE MOVING OR TRANSPORTING THE UNIT, MAKE SURE THAT:
ALL HEAVY OBJECTS OR THAT MIGHT FELL OFF ARE REMOVED FROM
THE UNIT.
IF THE UNIT ARE ON CASTERS (WHEELS), MAKE SURE THAT ALL ARE
UNLOCKED.
THE UNIT MUST BE HANDLED BY AT LEAST 2 PERSONS.
WHEN LIFTING THE UNIT, USE BOTH OF YOUR HANDS, AND BEND YOUR
KNEES. REMEMBER TO ALWAYS LIFT WITH YOUR LEGS, NOT YOUR BACK.
- IN CASE OF DAMAGE TO ANY PARTS, NOTIFY THE VENDOR AS SOON AS
POSSIBLE.
- IN CASE OF GLASS BREAKAGE (IF THE UNIT HAS A GLASS TABLE TOP OR
PARTS MADE OF GLASS) DO NOT HANDLE THE BROKEN GLASS WITH YOUR
BEAR HANDS, AND CONTACT THE VENDOR IMMEDIATELY. DO NOT ALLOW
CHILDREN NEAR THE BROKEN GLASS.
CARE AND MAINTENANCE