Techni Mobili RTA-8409 User manual

MIGHT REQUIERE
OF 2 PERSONS
Imported By
Thank you for purchasing one of our products.
Please read carefully the assembly instructions before the installation.
Do not discard this manual or any of the packaging material until the unit
has been completely assembled.
MODEL RTA-8409
ASSEMBLY INSTRUCTIONS

Hutch top panel Hutch left
panel
Hutch right
panel
Hutch middle
panel
Hutch horizontal panel Main panel
Left panel Right panel Middle panel Bottom panel
Adjustable panel
Foot panel Left back panel Drawer front panel Drawer left panel
MAIN PARTS LIST
P.2
RTA-8409
P.2

Drawer right panel Drawer back panel Drawer bottom panel Right back panel
MAIN PARTS LIST
P.3
RTA-8409
P.3
HARDWARE LIST:
Parts 1-13 come together; parts 14 come separate.
Part
No. Figure Description Qty
18x25mm wooden pins
(dowels)
40
215mm cam locks and bolts 9 sets
3M5x40mm screws 19
4M4x38mm screws 4
5M3.5x16mm screws 4
6M5x8mm euro screws 4
7Handle “L” shape (84mm)
and 2 of M3.6x24mm screws
1 set
8Metal pins 4
915mm cam lock caps 5
10 Screws caps 10
11 Nail-in plastic glides 6
12 Corner brackets 2
13 M3x16mm screws for
brackets
4
14 Drawer sliders 350mm
(1 set of 4 pcs)
Come in separate package
1 set
MAIN PARTS LAYOUT
(FOR REFERENCE):

BEFORE YOU START THE ASSEMBLY, PLEASE READ THE FOLLOWING TIPS AND WARNINGS.
P.4
RTA-8409
P.4
•Do a quick inventory to make sure the product contains all the parts and hardware.
•Missing, damaged and defective parts can be replaced at no cost to you. Please refer to the CONTACT card
included with the product.
•The replacement parts service is limited to the continental United States. If you reside in Hawaii, Puerto Rico,
U.S. Dependencies or other countries, please contact the supplier from where the unit was purchased.
•
If during assembly you find an issue or need clarification, please contact our Customer Service for assistance.
Please refer to the CONTACT card included with the product.
•On each step read the instructions and analyze the illustrations thoroughly before proceeding to do the
assembly.
•Make sure you understand which hardware will be used on each step. Using the wrong size of screw, bolt or
pin might strip the threads or cause damage to the part in which it is being used.
•To avoid misalignments, always leave the screws loose and tighten them until all pieces are positioned
correctly.
•Do not overtighten or force the screws as they might break, strip, damage the threads of the holes or get
stuck inside the part.
•Sometimes the laminate might cover partially or entirely the hole on a panel, but the hole should still be
located under the laminate.
•If there is no visible hole for the screw, pass and press the tip of your finger over the area where the hole
should be located to feel the indentation, and once found, carefully pierce the laminate to reveal the hole
underneath.
•If the hole seems too small for the screw, first make sure you are using the correct size of screw and that it’s
been installed in the correct hole. If the hole still appears to be too small, carefully pierce the laminate to
reveal the hole’s actual size.
☛This unit uses cam bolts and locks. The following explains how to use them.
This is not an assembly step; it is a guide for when you are actually doing the assembly using this
kind of hardware.
1. Screw the bolt into the
corresponding panel.
2. In the other panel, insert the
cam lock and align it so it can
properly receive the bolt, then join
both panels.
3. The panels might have a very
small gap which is normal; turn the
cam lock clockwise to lock the
parts together and the gap will also
close.
Cam Bolt Cam Lock
ALIGNMENT
DIRECTION

ASSEMBLY STEPS
P.5
RTA-8409
P.5
Install wooden pins (1) into panels (A), (B), (C), (D), (E), (G), (H), (I), (J), (L), (M), (O) and (P)
in the holes shown in the illustrations. Please note that other holes on the panels are
intended for other hardware in other steps. After done, set the panels aside to use on future
steps. DO NOT JOIN ANY PANELS, JUST INSTALL THE PINS.
Install the bolts (2) into the panels (E), (F) and (N) in the holes shown in the illustrations.
Please pay attention to the correct holes to use as other holes on the panels are intended
for other hardware in other steps. After done, set the panels aside to use on future steps.
STEP 1
Hardware:
1
8x25mm
x40
STEP 2
Hardware:
2
15mm
x9