Teknion interpret Leg Accommodation Kit WWSLK Operating and maintenance instructions

Part and Product Identification
For Customer Support please contact
[email protected]
Section:
Description: Page No:
Date:
Rev. No: 1
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
Jun. 2017 1 of 9
INT_013
Leg Accommodation Kit (WWSLK), Wire Gap Worksurface (WWWRW)
A - End Leg Assy
Angled
(N02-3687) x2
or
B - End Leg Assy
Straight
(N02-3686) x2
C3 - 5/16-18 Hex
Nut 1/2 A/F
.265 Thick
(E01-0755) x24
F - Front Standoff
(B02-0658)
48"-66" x1
72"-96" x2
I1 - Worksurface Spacer
Block
(A25-0547) x4
H - #10x0.875 Pan Wash
Screw (E07-0077) x4
48"-60" x4
66"-96" x8
I2 - 5/16-18x3.75 Hex
Head Grade 2 Screw
(E01-0799) x10
I3 - 5/16-18Hex Nut
1/2 A/F.265 Th.
(E01-0755) x10
G - Cantilever Bracket
(A16-4882)
48"-60" x2
66"-96" x4
E - Center Rail End
Cap
(N02-2149) x2
Straight Leg Frame 72" Frame shown
Note: Leg Accommodation Kit to be used
for 72" Wide Max, 60" Deep Max Double
Sided Bench for Users with Knee Clearance
Issues.
C1 - Transverse
Beam Sub-
Assembly
(N02-3688) x3
C2 - 5/16-18x2.5 Soc.
Head Cap Screw
(E01-0756) x24
N02-2090
D1 - Center Rail Ext.
Cap Cut Lenght
(A23-4058) x1
D2 - Center Rail Ext.
Cut Lenght
(A23-3734) x1
X02-0116
Pre assembled
B
D2
J1
Wire Gap
Worksurface
(WWWRW) x2
interpret Installation Guides
Leveler Cover is located inside Leg,
assembled and secured in place with tape.
Cantilevers (shown) are
delivered with Frame. These
will NOT be used. KEEP
ON SITE FOR FUTURE
RETROFIT.
WWSLK
J1 - Cross Bar for
Knee Clearance
(A16-4872) x2
J2 - Spacer Bracket
(A25-0548) x4
J4 - #10x0.875 Pan
Wash Screw
(E07-0077) x8
J3 - 1/4-20 x 7/8 Quadrex,
Truss Head Mach.
Screw (E01-0872) x4
J5 - 5/16-18 Hex
Nut 1/2 A/F
.265 Thk
(E01-0755) x8
J6 - 5/16-18 x 2 Long, Socket
Head Cap Screw
(E01-0764) x4
J7 - Screw 5/16-18 x 2 1/2 LG
Hex Head (E01-1136) x4
J2
C1
I1
F
E
D1

Section:
Description: Page No:
Date:
REMOVE MOUNTING SCREWS REMOVE MOUNTING SCREWS AND NUTS
INT_013
2 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
STEP 2: Remove Clamp Brackets from Mid Gable Connection position and move them one
hole over in direction as indicated above.
STEP 1: Remove two mounting Screws and Nuts from each Transverse Beam Assembly Clamp
as shown. Save to used for to Gables installation.
Determine what kind of connection there are on each end.
C1
End Gable
Connection C2
Mid Gable
Connection
C3
Mid Gable
Connection
interpret Installation Guides

Section:
Description: Page No:
Date:
REINSTALL CLAMPS DETAIL
INT_013
3 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
STEP 3: Install Clamps to create End Gable Connection. Repeat with all 3 Transverse Beams.
Mid Gable Connection
End Gable Connection
End Gable
Connection
Clamp Bracket and
Transverse Tube
alignment.
Clamp Bracket and
Transverse Tube
alignment.
Mid Gable Position: See through Clamp, you can see the Bolt
Transverse Beam is installed one set of holes over.
End Gable Position: You can't see Bolt through the Clamp
Transverse Beam is touching the End Gable
interpret Installation Guides

Section:
Description: Page No:
Date:
BEAM AND GABLE ASSEMBLY FASTEN WITH SCREWS AND NUTS
INT_013
4 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
B
C1
Leave connection loose to allow future
adjustment.
STEP 5 : Fasten together using Socket Cap Screw and Nuts, previously removed from
assembly.
STEP 4: Bring End Gables and Central Transverse Beam Assembly together. Assembly is
shipped loosely assembled so there should be enough clearance. Adjust if necessary. Line up the
middle set of holes on the top of End Gable beams with Clamp Brackets holes.
Middle pair of holes.
Position End Gables
with holes facing inward.
C3
C2
interpret Installation Guides

Section:
Description: Page No:
Date:
INSTALL SIDE TRANSVERS BEAMS ASSEMBLIES SECURE WITH FASTENERS AND LEVEL
INT_013
5 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
C1
STEP 7: Fasten Clamp Brackets to the Beam using mounting Screws and Nuts previously
removed from assembly. Level and square.
STEP 6: Angle remaining Transverse Beam assemblies and engage them into End Gable Cross
Beams at holes shown on illustration above.
EQ
EQ
C2
C3
interpret Installation Guides

Section:
Description: Page No:
Date:
INSTALL CROSS BAR AND SPACERS CENTRE RAIL ASSEMBLY
INT_013
6 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
J5
STEP 9: Prepare Center Rail for installation by sliding mounting Bolts into the channels
underside of the Rail. Slide End Caps on both sides. Tighten Set Screws to secure in place.
STEP 8: Place Cross Bar on the top of the middle Tube. Insert top part of Spacer Block and
Install Spacer Bracket. Push Front Standoff clips into the middle of both side Transverse Beam
assemblies.
Refer to Installation Guides# 401a, 402a, 406a for Wire Management and Electrics section.
I2
D2
E
SIDE VIEW
Set Screws
interpret Installation Guides
J7
J6
J2
J1 F
I1
J5
J7

Section:
Description: Page No:
Date:
INSTALL CENTRE RAIL SECURE IN PLACE
INT_013
7 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
Underside view
STEP 11: Use Spacer Blocks and Nuts to fasten the Rail to the frame. Install Top Cap if there
are no Screens or Storage specified. Otherwise save it for future installation.
STEP 10: Turn Center Rail so the Hex Cap Screws are facing down. Slide Screws inside the Rail
to line them up with corresponding holes on the Cross Bar, Clamp Brackets and Worksurface
Spacer Block. Drop the Rail on the top of middle Transverse Beam. Make sure all Screws are
inserted into the holes.
I1
D2
I3
interpret Installation Guides
D1
I3

Section:
Description: Page No:
Date:
SQUARE AND LEVEL WHOLE ASSEMBLY LOCK LEVELERS
INT_013
8 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
STEP 13: Lock each leveler and remove tape so Leveler Cover can slide down.STEP 12: Square and level whole assembly.
90°
interpret Installation Guides
Remove tape so
Leveler Cover can
slide down.

Section:
Description: Page No:
Date:
INSTALL WORKSURFACE SECOND WORKSURFACE
INT_013
9 of 9
Jun. 2017
LEG ACCOMODATION KIT
FRAMES, SUPPORTS AND WORKSURFACES
interpret Installation Guides
Wire Gap
Worksurface
J4
J3
Underside View Top View
Inserts to use -
End Gable Connection
STEP 14b: Repeat with the second Worksurface.STEP 14a: Line up Wire Gap Workusrface inserts with circular holes on Clamp Brackets. Drop
it on the Frame and fasten with Machine Screws and Washer Screws as shown.
NOTE: Install Peninsula Support Kit and
Peninsula Worksurface first if specified. Refer to
Installation Guide No. INT_006a and INT_006b
for Information.
J4 J3