Teknion Leverage User manual

OR
OR
OR
OR
Panel End Trim (KTE/KTED), Intermediate Panel End Trim (KTI/KTID),
Top Trim (KTR/KTRD), Continuous Top Trim (KTRC/KTRCD), Top Trim
(KTKT/KTKC)
Part and Product Identification
A1 -Top Trim (A23-1366) x1
OR
Thick Top Trim (A23-4597) x1
OR
Wooden Top Trim (N09-1184) x1
Section:
Description: Page No:
Date:
Rev. No: 1
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
May 2020 1 of 8
TLE_211
leverage Installation Guides
A2 -Top Trim Clip
(B02-0329) x 1
B1 -Panel End Trim
(N02-0497) x 1
OR
Panel End Trim - Wood
(N09-1185) x 1
A3 -Top Trim Connection Clip
(B02-0202) x 1
A- Top Trims
B- End Trims
B2 -Full Panel End Gasket
(B11-0178) x 2
OR
Full Panel Slim End Gasket
(B11-0573) x 2
C- Intermediate End Trims
C1 -Intermediate Panel End Trim
(N02-0627) x 1
OR
Intermediate Panel End Trim - Wood
(N09-1186) x 1
C2 -Intermediate End Gasket
(B11-0179) x 2
OR
Intermediate Slim End Gasket
(B11-0575) x 2
C3 -End Trim to Intermediate
Trim Connecting Pin
(B02-0207) x 1
B1
A1
C1

STEP 2: Place Top Trim with Clips attached onto the top of the Panel(s).STEP 1: Attach Top Trim Clips (Qty varies) on Top Trim by turning them clockwise.
Section:
Description: Page No:
Date:
ATTACH TOP TRIM CLIPS PLACE TOP TRIM ONTO PANEL(S)
TLE_211
2 of 8
May 2020
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
Top Trim Shown Continuous Top Trim Shown
NOTE: Make sure Clips
are fully engaged.
Side View Shown.
A2
A1
A1 A1
A1

Section:
Description: Page No:
Date:
CONNECT TWO TOP TRIMS TOGETHER
May 2020 3 of 8
TLE_211
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 3: Slidr the Connection Clip into the Trim slot, attach the Top Trim to connect to, and slide it against the other one using the Connection Clip as alignment.
NOTE: A 132" gap should be maintained between each Top Trim.
1
2
3
A1
A3

Section:
Description: Page No:
Date:
END TRIM INSTALLATION (STD WIDTH)
May 2020 4 of 8
TLE_211
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 4: Slide Gaskets onto Panel grooves and attach End Trim by pushing it against the Panel side.
B1
B2
Top View Shown.

Tear away part of End Gasket
on the side where Corridor
Width Elements are placed.
Section:
Description: Page No:
Date:
END TRIM INSTALLATION (CORRIDOR WIDTH)
May 2020 5 of 8
TLE_211
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 5: Slide Gaskets onto Panel grooves and attach End Trim by pushing it against the Panel side.
B1
B2
Top View Shown.

Section:
Description: Page No:
Date:
ATTACH CONNECTION CLIP FOR INTERMEDIATE END TRIM (IF APPLICABLE)
May 2020 6 of 8
TLE_211
END TRIMS AND TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 6: Slide Intermediate Connection Clip in to the Top Trim slot, then snap Top Trim onto Panel.
Back View Shown.
A1
C3
A1
C3

Section:
Description: Page No:
Date:
INTERMEDIATE END TRIM INSTALLATION (STANDARD ELEMENT WIDTH)
May 2020 7 of 8
TLE_211
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 7: Slide Gaskets into Panel Slots, place the Intermediate End Trim onto the Connecting Pin and snap into the Panel.
Top View Shown.
C2 C1
C3

Tear away part of End Gasket
on the side where Corridor
Width Elements are placed.
Section:
Description: Page No:
Date:
INTERMEDIATE END TRIM INSTALLATION (CORRIDOR ELEMENT WIDTH)
May 2020 8 of 8
TLE_211
END TRIMS & TOP TRIMS
PANEL CONNECTIONS & TRIMS
leverage Installation Guides
STEP 7: Slide Gaskets into Panel Slots, place the Intermediate End Trim onto the Connecting Pin and snap into the Panel.
Top View Shown.
C2
C1
C3