Teknion dna-SQUARE COFFEE TABLE User manual

dna - Square Coffee Table (NDNS_CU)
Section:
Description: Page No:
Date:
Rev. No: 1
dna-SQUARE COFFEE TABLE
SOFT SEATING
Sep 2019 1 of 10
TSC_302d
seating Installation Guides
NOTE: dna Square Coffee Table,
Double Access Door and
CLUBtalk Metal Enclosure will be
shipped assembled
B
C3
C5
A

Part and Product Identification
C1 - Power Bar - 3 Outlets
(YEPSC) x1
Section:
Description: Page No:
Date:
Rev. No: 1
dna-SQUARE COFFEE TABLE
SOFT SEATING
Sep 2019 2 of 10
TSC_302d
seating Installation Guides
Part and Product Identification
A - (N09-4430) x1
A1 - Power Bar Shroud, CLUBtalk
(A16-1970) x1
A2 - #10 x 1/2" Tap Screw, Quad, Pan
(E01-0023) x4
B2 - Double Access Door
(WWEDD) x1
B1 - dna Square Coffee Table
(NDNS) x1
A3 - #6 x 5/8" Tapping Screw; Type
AB; Pan Phillips; Zinc Chromat
(E07-0094) x2
C - (CUT) x1 Optional
C2 - Sensor x4
(AX-SE200HD) or
(AX-SE201DP) or
(AX-SE202VG)
C3 - Switcher
(AX-SW4) x1
C4 - Screws
(Supply with Manufacture)x1
C5 - Wireless Transmitter
(AX-WK300-TX) x1

STEP 2: Loosen Screws and remove Metal Enclosure from the Table
NOTE: Make sure to keep the Screws for future installation
STEP 1: Open dna Square Coffee Table
Section:
Description: Page No:
Date:
OPEN TABLE REMOVE METAL ENCLOSURE
TSC_302d
3 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
A
A2

Section:
Description: Page No:
Date:
REMOVE POWER BAR SHROUD
Sep 2019 4 of 10
TSC_302d
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
STEP 3: Remove Power Bar Shroud and Screws on the side of Enclosure as shown
NOTE: Make sure to keep the Screws for future installation
A1
A3

STEP 5: Refer to STEP 3 to remount Power Bar Shroud onto Metal EncloserSTEP 4: Mount Power Bar Shroud onto Power Bar as shown
Section:
Description: Page No:
Date:
MOUNT POWER BAR POWER BAR SHROUD ASSEMBLY
TSC_302d
5 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
C1

STEP 7: Feed Sensor Cable into the Metal Enclosure and attach Sensor onto the Sensor HolderSTEP 6: Feed Power Bar Cable into Metal Enclosure and through the cut-out in bottom as
shown
Section:
Description: Page No:
Date:
FEED POWER BAR CABLE FEED SENSOR CABLE
TSC_302d
6 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
Determined length
Temporary coiled for
future use. Tie with Zip
Ties
NOTE: Side View
Determined
length
Temporary coiled for
future use. Tie with Zip
Ties
C2

STEP 9: Place all devices into the Enclosure. Align Transmitter with hole on the side of Metal
Enclosure then fasten with Screws previously removed.
STEP 8: Feed Wireless Transmitter Cable inside the Metal Enclosure. Then connect cables with
Switcher
Section:
Description: Page No:
Date:
FEED TRANSMITTER CABLE & PLUG CABLES PLACE SWITCHER & TRANSMITTER ASSEMBLY
TSC_302d
7 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
NOTE: Reverse View NOTE: Detail View
C3
C5
C2

STEP 11: Place Power Brick inside the CLUBtalk Holding Brackets and feed cable through the
cut-out as shown
STEP 10: Align holes under Transmitter and Enclosure fasten with Screws provided
Section:
Description: Page No:
Date:
POSITION SWITCHER & MOUNT TRANSMITTER FEED CABLE THROUGH METAL ENCLOSURE
TSC_302d
8 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
C4
Cable for Switcher

STEP 12b: Feed Cables through the dna Table if power source is not located under the TableSTEP 12a: Plug Cables to power source
Section:
Description: Page No:
Date:
CONNECT TO POWER SOURCE FEED CABLE THROUGH COFFEE TABLE
TSC_302d
9 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
Floor Monument
from building.
Not supplied

STEP 14: Please proceed with Installation Guide TSC_302a for further more installationSTEP 13: Secure Metal Enclosure inside the Table with Screws
Section:
Description: Page No:
Date:
METAL ENCLOSURE ASSEMBLY TABLE ASSEMBLY
TSC_302d
10 of 10
Sep 2019
dna-SQUARE COFFEE TABLE
SOFT SEATING
seating Installation Guides
A2