Tekon PLUS TWP4AI User manual

TEKON ELECTRONICS AVEIRO, PORTUGAL
P.: [phone] M.: [phone] E.: [e-mail]
PLUS WIRELESS SYSTEM
INSTALLATION GUIDE
TEKON ELECTRONICS AVEIRO, PORTUGAL
P.: [phone] M.: [phone] E.: [e-mail]
IG.PLUS.ENG.V01.1.2018

2
DUOS WIRELESS SYSTEM INSTALLATION GUIDE
01
step WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
Pages 4 to 12
02
step TWP4AI PLUS WIRELESS TRANSMITTER CONFIGURATION
Pages 13 to 19
PLUS WIRELESS SYSTEM
INSTALLATION GUIDE
Table of contents
03
step TWP4AI TRANSMITTER ANALOG INPUT CONFIGURATION
Pages 20 to 23
04
step TWP4AI TRANSMITTER DIGITAL INPUT CONFIGURATION
Pages 24 to 26

3
DUOS WIRELESS SYSTEM INSTALLATION GUIDE
PLUS WIRELESS SYSTEM
INSTALLATION GUIDE
Table of contents
05
step TWP4AI TRANSMITTER DIGITAL OUTPUTS CONFIGURATION
Pages 27 to 32
07
step WRP001 PLUS WIRELESS REPEATER CONFIGURATION
Pages 36 to 41
08
step SITE SURVEY MODE
Pages 42 and 43
06
step WGW420 GATEWAY ANALOG OUTPUTS CONFIGURATION
Pages 33 to 35
5.1 LINK LOST OUTPUT
Page 28
5.2 REMOTE CONTROL OUTPUT
Page 30
5.3 EXTERNAL POWER CONTROL OUTPUT
Page 31

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
5
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
01 Connect the antenna to the Gateway.
02 Wiring
Connect the power supply and then the
RS485-USB cable to the Gateway.
TEKON CONFIGURATOR SOFTWARE is only compatible with the Microsoft® Windows® Operating System.
03 Power ON the device.
Wire Indication:
Blue - GND; Brown - +24 VDC; Orange - Data+ (A); Black - GND; Yellow - Data - (B)

6
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
04 Check device connection state by LED indication.
05 Open Tekon Congurator Software1and select PLUS >> Gateway >> Conguration
2
1
3
1 Tekon Congurator software is free of charge and available at www.tekonelectronics.com
10 Seconds to enter
conguration mode
WIRELESS GATEWAY
Normal mode
Green LEDs
permanently on
Red LEDs
permanently on

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
7
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
07 Select corresponding Port name2.
2You can check device’s serial port name in “Device Manager” on Microsoft ® Windows® operating system.
06 Select serial port corresponding to WGW420 PLUS Wireless Gateway
Click on the Rescan Ports button.

8
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
08 Perform a power cycle on the Gateway.
09 Click on Connect ( ) button to enter conguration mode.
NOTE:
After power up, you have 10 seconds to enter conguration mode by clicking on Connect button ( )
(while green LEDs are permanently on).
In this mode, you can manage device parameters: Modbus Address, Modbus Baudrate, Modbus Parity, Wireless
Network ID and Wireless Channel.

01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
9
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
NOTE:
When the 10-second time frame to enter conguration mode is exceeded, the LEDs will turn permanently red and
the gateway will enter normal operation mode.
To re-enter conguration mode, a power reset must be performed - step 8.
Green LEDs performing
scan animation
WIRELESS GATEWAY
Conguration mode
The status string at the bottom of the software window provides feedback on ongoing operations.
09
You can also verify conguration mode activation by checking LEDs on the gateway.

10
PLUS WIRELESS SYSTEM INSTALLATION GUIDE
01
step
WGW420 PLUS WIRELESS GATEWAY CONFIGURATION
11 Click on Disconnect ( ) button.
10 Take note of device conguration data available, namely: Modbus Address, Modbus Baudrate, Modbus Parity,
Wireless Network ID and Wireless Channel.
NOTE:
The wireless network connection between devices is ensured by setting the same Wireless Network ID and
Wireless Channel parameters.