Tektronix TDS5000B Series User manual

Instructions
Option 1R
Rackmount Kit
TDS5000B Series
Digital Phosphor Oscilloscopes
071-1421-01
*P071142101*
071142101
Warning
The servicing instructions are for use by qualified
personnel only. To avoid personal injury, do not
perform any servicing unless you are qualified to
do so. Refer to all safety summaries prior to
performing service.
www.tektronix.com

Copyright ©Tektronix. All rights reserved. Licensed software products are owned by Tektronix or its subsidiaries or
suppliers, and are protected by national copyright laws and international treaty provisions.
Tektronix products are covered by U.S. and foreign patents, issued and pending. Information in this publication supercedes
that in all previously published material. Specifications and price change privileges reserved.
TEKTRONIX and TEK are registered trademarks of Tektronix, Inc.
Contacting Tektronix
Tektronix, Inc.
14200 SW Karl Braun Drive
P.O. Box 500
Beaverton, OR 97077
USA
For product information, sales, service, and technical support:
HIn North America, call 1-800-833-9200.
HWorldwide, visit www.tektronix.com to find contacts in your area.

TDS5000B Series (Option 1R) Rackmount Kit 1
Service Safety Summary
Only qualified personnel should perform service procedures. Read this Service
Safety Summary and the General Safety Summary in the product service manual
or the instruction manual.
Do Not Service Alone. Do not perform internal service or adjustments of this
product unless another person capable of rendering first aid and resuscitation is
present.
To prevent the instrument and rack from falling onto the operator, two or more
installers should install the instrument into the rack cabinet. After completing the
installation procedure, the installers should verify that the instrument and rack
cabinet will not tip forward while the instrument is in the extended position.
Disconnect Power. To avoid electric shock, switch off the instrument power, then
disconnect the power cord from the mains power.
Use Care When Servicing With Power On. Dangerous voltages or currents may
exist in this product. Disconnect power and disconnect test leads before
removing protective panels, soldering, or replacing components.
To avoid electric shock, do not touch exposed connections.

Service Safety Summary
2TDS5000B Series (Option 1R) Rackmount Kit

TDS5000B Series (Option 1R) Rackmount Kit 3
Kit Description
This introduction describes the installation of the rackmount kit to your standard
bench-top instrument.
The rackmount kit is a collection of parts that, once installed, configure the
instrument for mounting into a standard 19-inch equipment rack.
Products
TDS5000B Series AllSerialNumbers
Kit Parts List
Figure 1
on page 4 Quantity Part number Description
-- -- -- -- -- -- -- -- -- 1ea 016-1887-XX RACKMOUNT KIT TDS5000B SERIES CON-
SISTING OF THE FOLLOWING:
-- -- -- -- -- -- -- -- -- 1 e a 071-1421-01 TECH MANUAL: INSTRUCTIONS, TDS5000B
SERIES
1-1 1 ea 386-7301-00 RACKMOUNT PANEL LEFT
1-2 1 ea 386-7302-00 RACKMOUNT PANEL RIGHT
1-3 4 ea NS SCREW, MACH: 10-32, PAN-HEAD, 0.5 IN I,
PHILLIPS
1-3 7 ea NS NUT, LOCKING WASHER: 10-32 ASSEM
1-3 20 ea NS SCREW, MACH: 10-32, TRUSS-HEAD, 0.375 IN
I, PHILLIPS
1-3 4 ea NS SCREW, MACH: M6 x 20 OVAL-HEAD,
PHILLIPS
1-3 4 ea NS SCREW, MACH: M5 x 20 OVAL-HEAD,
PHILLIPS
1-3 4 ea NS SCREW, MACH: 10-32 x 0.75 OVAL-HEAD,
PHILLIPS
1-3 4 ea NS SCREW, MACH: 12-32 x 0.75 OVAL-HEAD,
PHILLIPS
1-3 5 ea NS WASHER: FLAT, NYLON
1-4 2 ea 351-1095-00 SLIDE, DRAWER, EXTENDERS: SLIDERS
1-4 2 ea NS RACK: MOUNTING SCREWS, NUT BLOCKS
1-5 1 ea 200-4866-00 COSMETIC COVER, RACKMOUNT
1-6 1ea 386-7340-00 PLATE: SHEET METAL, GUARD BRACKET

Kit Description
4TDS5000B Series (Option 1R) Rackmount Kit
Figure 1
on page 4 DescriptionPart numberQuantity
1-7 1ea 386-7300-00 PLATE: STEEL, BRACKET SPACER
1-8 2ea 367-0525-00 HANDLE: BRACKET, AL, GRAY
NS - Not Saleable
1
2
3
4
5
6
7
8
Figure 1: Rackmount kit parts

Kit Description
TDS5000B Series (Option 1R) Rackmount Kit 5
When the instrument is installed according to the instructions in this document,
the rackmounted instrument meets all warranted requirements listed in the
instrument specification except for those listed in Environmental Requirements
on page 6. Instruments mounted using methods other than those described in
these instructions may not meet their warranted requirements.
See the specifications for your instrument model for tables of the warranted
characteristics.
Cooling air enters on the bottom and right sides as shown in Figure 2. You must
provide adequate cool air to meet the ambient temperature requirements listed in
Table 1.
Cool air in
Hot air out (rear)
Measure
input air
temperature
Figure 2: Instrument cooling
Warranted Characteristics

Kit Description
6TDS5000B Series (Option 1R) Rackmount Kit
The following environmental characteristics supercede those listed in the
specifications and performance verification sections of the manual for your
instrument.
Table 1: Warranted characteristics
Characteristic Description
Temperature, Inside Rack Cabinet
Operating +10 _Cto+45_C(+50_Fto+113_F)
Non-operating --22 _Cto+60_C(--7.6_F to +140 _F)
Shock
Operating and Non-operating 20 g, 11 ms, half sine, each axis, 3 drops
each
Clearance Requirements
The rack in which the rack adapted instrument is mounted must provide the
following clearance requirements:
HA minimum of 10.5 inches (266.7 mm) of vertical space.
HA minimum width of 17 5/8 inches (448 mm) between the left- and
right-front rails in the rack.
HA minimum depth of 20 inches (508 mm).
CAUTION. Adhering to these clearance requirements provides the rack-mounted
instrument with sufficient clearance for air circulation and accommodation of
the power cord and mounting hardware. Failure to provide these clearances can
result in overheating and can cause instrument faults or failure.
Environmental
Requirements

Kit Description
TDS5000B Series (Option 1R) Rackmount Kit 7
161.925 mm
(6.375 in)
500.024 mm
(19.686 in)
421.64 mm
(16.80 in)
323.850 mm
(12,750 in)
50.80 mm
(2.00 in)
60.325 mm
(2.375 in)
30.480 mm
(1.200 in)
265.938 mm
(10.470 in)
482.600 mm
(19.000 in)
29.72 mm
(1.170 in)
465.480 mm
(18.326 in)
258.639 mm
(10.160 in)
215.900 mm
(8.50 in)
348.048 mm
(15.120 in)
Figure 3: Instrument with rack adapter installed

Kit Description
8TDS5000B Series (Option 1R) Rackmount Kit