Tele Radio TG-TX-MNL6 Installation instructions

TG-TX-MNL6 (TG-T9-2), TG-TX-MNR6 (TG-T9-12), TG-TX-MNP6 (TG-T9-22), TG-TX-MDL10 (TG-T11-4),
TG-TX-MDR10 (TG-T11-14), TG-TX-MDP10 (TG-T11-24), TG-R4-1 (TG-RX-MNL7), TG-R4-3 (TG-RX-MNR7),
TG-R4-5 (TG-RX-MNP7), TG-R4-46 (TG-RX-MDL12), TG-R4-48 (TG-RX-MDR12), TG-R4-50 (TG-RX-MDP12),
TG-R4-6 (TG-RX-MDL17), TG-R4-8 (TG-RX-MDR17), TG-R4-10 (TG-RX-MDP17), TG-R4-26 (TG-RX-MNLCAN),
TG-R4-28 (TG-RX-MNRCAN), TG-R4-30 (TG-RX-MNPCAN), TG-R4-41 (TG-RX-MNLJ1939), TG-R4-43 (TG-RX-MNRJ1939),
TG-R4-45 (TG-RX-MNPJ1939, TG-R4-36 (TG-RX-MNLANA), TG-R4-38 (TG-RX-MNRANA), TG-R4-40 (TG-RX-MNPANA)
LANGUAGE: English (original)
IM-TG2-ED002-A11-EN

Enduserinstructions

CONTENTS
Chapter1:CUSTOMERINFORMATION 3
Chapter2:ENDUSERINSTRUCTIONS 5
Startthetransmitterinoperatingmode 9
StartthetransmitterinoperatingmodewithPINcodes 10
StartthetransmitterinoperatingmodeusingRFID 10
Turnthetransmitteroff 11
Login/logout 11
Replace 12
Automaticshutdown 13
Frequencies&channels 13
RoHSandWEEE 18
Guarantee,service,repairsandmaintenance 19
Chapter3:EC/EEADECLARATIONOFCONFORMITY 20
-2-

Chapter 1: CUSTOMER INFORMATION
CHAPTER 1: CUSTOMER INFORMATION

THANK YOU FOR PURCHASING A TELE RADIO AB PRODUCT

READALLINSTRUCTIONSANDWARNINGSCAREFULLYBEFOREUSING
THEPRODUCTS.

TheseinstructionsarepublishedbyTeleRadioABwithoutanyguarantee.Theinstructionsmay
beremovedorrevisedbyTeleRadioABatanytimeandwithoutfurthernotice.Correctionsand
additionswillbeaddedtothelatestversionoftheinstruction.

IMPORTANT!Theseinstructionsaredirectedtowardsendusers.Theycanbeprintedand
handedtoendusers.Theinstallationinstructionsthatcontaininformationontheinstallationand
configurationoftheradioremotecontrolunitonthemachinearenotintendedtobepassedonto
theenduser.Onlysuchinformationmaybepassedontotheenduserthatisneededtooperate
themachinecorrectlybyradioremotecontrol.

TeleRadioABproductsarecoveredbyaguarantee/warrantyagainstmaterial,constructionor
manufacturingfaults.Duringtheguarantee/warrantyperiod,TeleRadioABmayreplacethe
productorfaultypartswithnew.Workunderguarantee/warrantymustbecarriedoutbyTele
RadioABorbyanauthorizedservicecenterspecifiedbyTeleRadioAB.ContactyourTele
RadioABrepresentativeifyouneedsupportorservice.

©TeleRadioAB,2013
Datavägen21
SE-43636ASKIM
SWEDEN
Tel:+46-31-7485460
Fax:+46-31-685464
www.tele-radio.com




END USER WARNINGS & RESTRICTIONS

l Onlyqualifiedpersonnelshouldperformtheinstallationandsettingsforthesystem.
l Donotopenthereceiverencapsulationunlessyouarequalified.
l Readandfollowtheenduserinstructionscarefully.
l Youmusthavereachedthecertifiedageofyourcountrytooperatetheequipment.
l Itisstrictlyprohibitedtooperatetheequipmentundertheinfluenceofdrugs,alcoholand
medicines.
l Keeptheproductsinadry,cleanplace.
l Keepcontactsandantennasclean.
l Wipeoffdustusingaslightlydamp,cleancloth.
l Neverusecleaningsolutionsorhigh-pressurewater.
l Checkthetransmitterencapsulationandfoilfordamageseveryday.Ifyouusethe
transmitteralthoughtheencapsulationorfoilisdamaged,moisturecancauseserious
damagetotheelectronics.Theguarantee/warrantydoesnotcoverthecostofrepairing
suchdamagescausedbymoisture.Contactyourrepresentativeimmediatelyifyoufind
anydamagetothetransmitter,orifyourequireservicefororotherassistancewithyour
transmitter.


-3-

Chapter 1: CUSTOMER INFORMATION



APPLICATION AREA FOR THE TIGER SYSTEM

TheTeleRadioABTigerremotecontrolsystemsareaimedforremotecontrollingofliftingor
mobileequipmentwhereahighsafetylevelisrequired.



AUTHORIZATION BY PIN CODE

Topreventfromunauthorizedusersbeingabletostartthetransmitterandcontrolthereceiver,
youcanenablePINcodesforstart-upprotection.1-10PINcodescanbestoredintheTG-TX-
MNL6,TG-TX-MNR6,TG-TX-MNP6andTG-TX-MDL10,TG-TX-MDR10,TG-TX-MDP10
transmitters.



STOP FUNCTION

Thetransmittershaveastopbuttonthatcontrolsthe2stoprelaysinthereceiver.2safety
microcontrollersaresupervisingandcontrollingthestoprelays.Avalidsignalmustbeprovided
frombothmicrocontrollerstoactivatethestoprelays.
-4-

Chapter 2: END USER INSTRUCTIONS
CHAPTER 2: END USER INSTRUCTIONS

1
2
3
4
5
7
8
9
10
11
6
6
7
15
10
11
8
9
13
1
2
3
4
5
12
14


1.Rubbercover 9.Button6**
2.Display 10.ButtonLEDs
3.Button1 11.Stopbutton
4.Button3 12.Button7***
5.Button5* 13.Button8***
6.TopLED 14.Button9****
7.Button2 15.Button10*****
8.Button4 

*onTG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6:leftstartbutton
**onTG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6:rightstartbutton
***onlyonTG-TX-MDL10,TG-TX-MDR10,TG-TX-MDP10
****onTG-TX-MDL10,TG-TX-MDR10,TG-TX-MDP10:leftstartbutton
*****onTG-TX-MDL10,TG-TX-MDR10,TG-TX-MDP10:rightstartbutton
-5-

TECHNICAL DATA

NO.OFBUTTONS
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 6x2-stepbuttons
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 10x2-stepbuttons

BATTERY
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 Internal,rechargeablelithium-ion
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 External,rechargeablelithium-ion

ON/OFFSWITCH
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 Yes
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 No

DUPLEXCOMMUNICATION
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10,
Possible

MAX.NOOFREGISTEREDRECEIVERS
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 4
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 8

SIZE
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 160x76x37mm./6.3x3x1.4in.
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 210x76x37mm./8.2x3x1.4in.

WEIGHT
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6 295g./0.6lbs.
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10 400g./0.9lbs.

OPERATINGFREQUENCY
TG-TX-MNL6,TG-TX-MDL10 433.075-434.775MHz
TG-TX-MNR6,TG-TX-MDR10 903.0125-926.9875MHz
TG-TX-MNP6,TG-TX-MDP10 2405-2480MHz

NO.OFCHANNELS/FREQUENCYBANKS
TG-TX-MNL6,TG-TX-MDL10 69
TG-TX-MNR6,TG-TX-MDR10 15
TG-TX-MNP6,TG-TX-MDP10 16

-6-

CHANNELSEPARATION
TG-TX-MNL6,TG-TX-MDL10 25kHz
TG-TX-MNR6,TG-TX-MDR10 25kHz
TG-TX-MNP6,TG-TX-MDP10 5MHz

OPERATINGTIME(WITHCONTINUOUSUSAGE
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10
16h.

IPCLASS
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10
66

SENSITIVITY
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10
Betterthan-110dBm

OPERATINGTEMPERATURE
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10
-20-+55°C/-4-+130°F

NO.OFPINCODESPOSSIBLE
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10
10

RADIOTYPE
TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6,
TG-TX-MDL10,TG-TX-MDR10,TG-TX-
MDP10,
LowIFtopology
-7-


Product measurements

TG-TX-MNL6,TG-TX-MNR6,TG-TX-MNP6

160 mm (6.3 1in)
76 mm (3 in) 46 mm (1.8 in)


TG-TX-MDL10,TG-TX-MDR10,TG-TX-MDP10

79 mm (3.1 in)
208 mm (8.2 in)
41 mm (1.6 in)
51 mm (2 in)



-8-

ON/OFF SWITCH

TheTG-TX-MNL6,TG-TX-MNR6,TG-TX-
MNP6transmitterhasanon/offswitchonthe
backside.Theswitchbreaksthepowersupply
fromthebattery.Wheninposition0/off,the
transmittercannotbestartedunlessyou
connectthechargerplug.Whenthe
transmitteristransportedbyairplane,the
on/offswitchmustbein0/offposition.The
switchshouldnotbeusedasanon/offbutton
forthetransmitter.Toturnthetransmitteroff,
usethestopbutton.




START THE TRANSMITTER IN OPERATING MODE

1.Makesurethatthestopbuttonispressed

2.Pulloutthestopbutton.
ThetopLEDlights(greenwhenthebatterycapacityisgood,redwhenthebatterycapacityis
poor).

3.IfPINcodesareusedforauthorization:Gotothenextsection.

4.WITHIN3MINUTESFROMPULLINGOUTTHESTOPBUTTON:
Pressabuttontoselectthereceiver(s)thatyouwanttooperate.
Thereceiver(s)thatwasselectedinthelastsessionwillbeautomaticallyselected,whichis
indicatedbythecorrespondingLED(s)thatlightred.Ifnoreceiver(s)hasbeenselected,the
LEDsforallavailablereceiverswillflashred.Ifareceiverisselected,theLEDsnexttotheleft
andtherightstartbuttonsflashred.Ifnoreceiver(s)areselected,onlytheLEDnexttotheright
startbuttonflashesred.

5.Pressbothstartbuttonsatthesametime.
Thebuzzerbeeps.

6.Releasethestartbuttons.
Thebuzzerstopsbeeping.ThetopLEDflashes(greenwhenthebatterycapacityisgood,red
whenthebatterycapacityispoor).

7.Whenradiocommunicationhasbeenestablished,thetopLEDlights(greenwhenthebattery
capacityisgood,redwhenthebatterycapacityispoor).
Ifradiocommunicationisnotestablishedwithin25seconds,thetransmitterturnsoff.



-9-

START THE TRANSMITTER IN OPERATING MODE WITH PIN
CODES

1.Makesurethatthestopbuttonispressed.

2.Pulloutthestopbutton.
ThetopLEDlights(greenwhenthebatterycapacityisgood,redwhenthebatterycapacityis
poor).

3.WITHIN3MINUTES:EnterthePINcode(4digits)bypressingthebuttonsaccordingtothe
table.

FORDIGIT: 1 2 3 4 5 6 7 8 9 0
TG-TX-MNL6,PRESSBUTTON: 1 2 3 4 - - - - - -
TG-TX-MDL10,PRESSBUTTON: 1 2 3 4 5 6 7 8 - -

4.WITHIN3MINUTESFROMPULLINGOUTTHESTOPBUTTON:
Pressabuttontoselectthereceiver(s)thatyouwanttooperate.
Thereceiver(s)thatwasselectedinthelastsessionwillbeautomaticallyselected,whichis
indicatedbythecorrespondingLED(s)thatlightred.Ifnoreceiver(s)hasbeenselected,the
LEDsforallavailablereceiverswillflashred.Ifareceiverisselected,theLEDsnexttotheleft
andtherightstartbuttonsflashred.Ifnoreceiver(s)areselected,onlytheLEDnexttotheright
startbuttonflashesred.

5.Pressbothstartbuttonsatthesametime.
Thebuzzerbeeps.

6.Releasethestartbuttons.
Thebuzzerstopsbeeping.ThetopLEDflashes(greenwhenthebatterycapacityisgood,red
whenthebatterycapacityispoor).

7.Whenradiocommunicationhasbeenestablished,thetopLEDlights(greenwhenthebattery
capacityisgood,redwhenthebatterycapacityispoor).
Ifradiocommunicationisnotestablishedwithin25seconds,thetransmitterturnsoff.



START THE TRANSMITTER IN OPERATING MODE USING RFID

NOTE!IfbothanRFIDtagandaPINcodeareusedforauthorization,itispossibletouseonly
thePINcode,e.g.ifyouhavelosttheRFIDtag.ThetransmitterwillaskfortheRFIDtaguntil
youhaveenteredthefirstdigitofthePINcode.

NOTE!ThetransmitterswillonlyacceptRFIDtagsfromTeleRadioAB.

1.Makesurethatthestopbuttonispressed.

2.Pulloutthestopbutton.
ThetopLEDlights(greenwhenthebatterycapacityisgood,redwhenthebatterycapacityis
poor).

-10 -