Tele Radio T70 Series User manual

T70RX-03AIB, T70RX-03AWB,
T70TX-02TTB, T70TX-03STB, T70TX-06TTB
LANGUAGE: English (original)

IM-T70-RX001-A01-EN

Installation instructions

CONTENTS
Chapter 1: CUSTOMER INFORMATION 3
Chapter 2: PRODUCT PAGES 5
Receiver description 5
T70RX-03AIB, T70RX-03AWB 5
Quick Fuse 6
Terminal block for input power 7
Current consumption 7
Technical data 7
Transmitter description 8
Technical data 8
Change batteries 9
Start the transmitter 9
Turn the transmitter off 9
Automatic shutdown 9
Register 10
Erase 10
Switch frequency 10
Frequency banks 11
Switch frequency bank 11
Frequency switch table 12
Settings for T70RX-03AIB + T70TX-06TTB 14
Register the transmitter in the receiver 14
Interlocking function 14
Settings for T70RX-03AWB + T70TX-06TTB 15
Register the transmitter in the receiver 15
Winch modes 15
Chapter 3: BATTERY GUIDE 16
Precautions 16
ROHs and WEEE 16
Guarantee, service and maintenance 16
-2-

Chapter 1: CUSTOMER INFORMATION
CHAPTER1:CUSTOMERINFORMATION

THANKYOUFORPURCHASINGATELERADIOABPRODUCT

READALLINSTRUCTIONS ANDWARNINGS CAREFULLY BEFOREMOUNTING, INSTALLING
ANDCONFIGURATING THEPRODUCTS.

These instructions are published by Tele Radio AB without any guarantee. The instructions may be
removed or revised by Tele Radio AB at any time and without further notice. Corrections and additions
will be added to the latest version of the instruction.

IMPORTANT! The instructions that contain information on the installation and configuration of the
radio remote control unit on the machine are not intended to be passed on to the end user. Only such
information may be passed on to the end user that is needed to operate the machine correctly by radio
remote control.

Tele Radio AB products are covered by a guarantee/ warranty against material, construction or
manufacturing faults. During the guarantee/ warranty period, Tele Radio AB may replace the product or
faulty parts with new. Work under guarantee/ warranty must be carried out by Tele Radio AB or by an
authorized service center specified by Tele Radio AB. Contact your Tele Radio AB representative if you
need support or service.

©Tele Radio AB. Revised 2012
Datavägen 21
SE-436 36 ASKIM
SWEDEN
Tel: [phone]
Fax: [phone]
www.tele-radio.com
-3-

WARNINGS&RESTRICTIONS

IMPORTANT! Tele Radio remote controls are often built into wider applications. We recommend that
the system is provided with a wired emergency stop where necessary.

INSTALLING, CONNECTING AND MOUNTING
n Allow only licensed or qualified personnel to install the product.
n Switch the power supply off to the receiver before connecting the equipment.
n Check that you have connected the power supply to the correct connection
terminal.
n Use undamaged cables. No cables should hang loose.
n Avoid installing in areas affected by strong vibrations.
n Place the receiver well away from wind, damp and water.
n Cable glands and vent plugs must face down to prevent water from seeping in.

THE USER
n Make sure that the user is following the instructions.
n Make sure that the user has reached the certified age of your country to oper-
ate the equipment.
n Make sure that the user is not under the influence of drugs, alcohol and med-
icines.
n Allow only qualified personnel to have access to the transmitter and operate
the equipment.
n Make sure that the user does not leave the transmitter unsupervised.
n Make sure that the user always turns the transmitter off when not in use.
n Make sure that the user keeps a good overview of the work area.

MAINTENANCE
n Always contact your representative for service and maintenance work on the
product.
n Write down the serial numbers/ ID codes of the receivers and transmitters
used. This information should be recorded on the “Settings document” for
your product (download from our website).
n Avoid registering transmitters to receivers where it is not being used.
n Keep the safety instruction for future reference. Always download the con-
figurations instruction from our web site for the latest version available.
-4-

Chapter 2: PRODUCT PAGES
CHAPTER2:PRODUCTPAGES

RECEIVERDESCRIPTION

T70RX-03AIB, T70RX-03AWB

WARNING! The receiver must NOT be opened by any other than a qualified installer. Make sure to
turn the electricity off before opening the receiver.




1. Relay LEDs 1-3 6. Code LED (red)
2. Function relays 1-3 7. Power supply LED (yellow)
3. Quick fuse 10A 8. Function LED (green)
4. Terminal block for input power 9. Function button
5. Antenna connector 10. Code button
-5-

QUICKFUSE





NOTE! With the 10 A fuse mounted and the receiver powered, voltage from the middle power supply
connection pin (12-24V AC/DC fused) is fed through the fuse to relay number 1 (pin 2, NO).

NOTE! The quick fuse is optional.
-6-

TERMINALBLOCKFORINPUTPOWER




CURRENTCONSUMPTION

Input power Minimum Maximum
12V DC 25 mA 100 mA
24V DC 15 mA 50 mA
24V AC 15 mA 50 mA



TECHNICALDATA

Input power 12-24V AC/DC
Function relays 3 potential free*, 8 A ACI
Radiotype Superheterodyne
Antenna 1 external antenna (BNC)
Channels 64
Operating frequency 433.075-434.650 MHz
Size 120 x 133 x 45 mm./ 4.7 x 5.2 x 1.8 in.
Weight 200 grams/ 0.4 lbs.
Max. no. of transmitters 1

* You need to supply voltage to get power out of a relay (e.g. via a connection comb)
-7-

TRANSMITTERDESCRIPTION

70TX-02TTB, T70TX-03STB T70TX-06TTB

1.Push button 1 6. Push button 6
2. Push button 2 7. Push button 7
3. Push button 3 8. Push button 8
4. Push button 4 9. Red LED
5. Push button 5 


Technical data

 T70TX-02TTB, T70TX-03STB T70TX-06TTB
Number of buttons 4 8
Batteries 3 x 5V AAA* 3 x 5V AAA*
Operating frequency 433.075-434.650 433.075-434.650
Channels 64 64
Size 113 x 65 x 35 mm./ 4.7 x 5.2 x 1.8 in. 113 x 65 x 35 mm./ 4.7 x 5.2 x 1.8 in.
Weight 120 grams/ 0.2 lbs. 120 grams/ 0.2 lbs.
IP class 65 65
Max. no. of receivers 1 2-3

* Use alkaline batteries for better performance
-8-

CHANGEBATTERIES


1. Remove the (a) clip (2 screws).
2. Remove the (b ) battery lid (2 screws).
3. Put the batteries in (3 x 1.5V AA batteries).
4. Put the battery lid (b) back (2 screws).
5. Put the clip (a) back (2 screws).



STARTTHETRANSMITTER

1. Press the ON button for at least 1 second until the red LED lights.
The red LED flashes when the transmitter is on.


TURNTHETRANSMITTEROFF

1. Press the OFF button.
The red LED goes out.


AUTOMATICSHUTDOWN

When no buttons have been pressed for 3 minutes, the transmitter turns off.


-9-

REGISTER

Only one transmitter can be registered in the receiver at a time. If you want to register a second
transmitter, you have to erase the first transmitter.

1. Start the receiver and the transmitter.

2. T70TX-02TTB, T70TX-03STB:
Press button 1. KEEPPRESSED UNTIL ALLSTEPS HAVEBEENPERFORMED.

T70TX-06TTB:
See Settings for T70RX-03AIB + T70TX-06TTB or Settings for T70RX-03AWB + T70TX-06TTB for what
button to press, depending on what receiver that you are using. KEEPPRESSED UNTIL ALLSTEPS
HAVEBEENPERFORMED.

3. Press the receiver Code button. Keep pressed until the red relay LEDs light.

4. Release the Code button. The receiver stays in registering mode for approx. 8 seconds.

5. Keep the transmitter button pressed. When the red relay LEDs flash 3 times, the transmitter is
registered in the receiver.

6. Release the transmitter button.



ERASE

1. Press the receiver Code button for over 6 seconds until the red Code LED goes out.


SWITCHFREQUENCY

1. Start the transmitter. Press the OFF button. Keep pressed.

2. WITHIN 3 SECONDS: Press the ON button. Keep both buttons pressed.

3. Release the transmitter buttons.

4. WITHIN 5 SECONDS:
Press transmitter button 1 to step 1 row up in the frequency table OR
Press transmitter button 3 to step 1 row down in the frequency table.
The red transmitter LED flashes 3 times when the frequency has been changed. The transmitter turns
off.

NOTE! If you want to step more than one row up or down in the frequency table, you need to restart
the transmitter and go over the steps above again.

When you have switched frequency, connecting the transmitter and receiver can take a little while
longer.


-10 -

FREQUENCYBANKS



SWITCHFREQUENCYBANK

l The default setting in the transmitter is channel 1 in frequency bank 1.
l You have to switch frequency before you register the transmitter in the receiver.
l If the transmitter is already registered in a receiver, you have to erase the transmitter from that
receiver. You can then switch frequency and register the transmitter in a receiver.

NOTE! The transmitter must be turned off when switching frequency bank.


-11 -

FREQUENCYSWITCHTABLE

FREQUENCYBANK SWITCH1 SWITCH2
1 OFF OFF
2 ON OFF
3 OFF ON
4 ON ON


1a. Remove the clip (2 screws).
1b. Remove the battery lid (2 screws).



2a. Remove the batteries. Remove the battery casing (2 screws).
2b. The frequency switches are placed to the left on the circuit board (see picture).


-12 -

4. Put the battery compartment back on the circuit board (4 screws).
5. Put the 3 batteries back.
6. Put the battery lid back (2 screws).
7. Put the clip back (2 screws).


-13 -

SETTINGSFORT70RX-03AIB+T70TX-06TTB

Register the transmitter in the receiver

To register the transmitter in the 1st receiver:
Press transmitter button 1, 2 or 3 (see picture).

To register the transmitter in the 2nd receiver:
Press transmitter button 4, 5 or 6 (see picture).



Interlocking function

When interlocking is enabled, only one relay can be activated at the same time. When interlocking is
disabled, several relays can be activated at the same time. Default= no interlocking (receiver Function
LED = off).

Turn interlocking on/ off
1. Start the receiver and transmitter.
2. Press the receiver Function button.
3. The receiver Function LED lights green when interlocking is activated. To turn the interlocking
function off, press the receiver Function button until the LED goes out.



-14 -

SETTINGSFORT70RX-03AWB+T70TX-06TTB

Register the transmitter in the receiver

To register the transmitter in the 1st receiver:
Press transmitter button 1 or 4 (see picture).

To register the transmitter in the 2nd receiver:
Press transmitter button 2 or 5 (see picture).

To register the transmitter in the 3rd receiver:
Press transmitter button 3 or 6 (see picture).





Winch modes

Winch mode I
Relay 1 activates when relay 2 or 3 activates (green Function LED= off).

Winch mode II
Relay 1 activates and stays on for 30 seconds when relay 2 or 3 is activated.




Switch between Winch mode I and Winch mode II
1. Start the receiver and transmitter.
Press the receiver Function button. When the Function LED lights green, Winch mode II is selected.
When the Function LED is off, Winch mode I is selected. To switch winch mode, press the Function
button until the Function LED lights or goes out.

-15 -

Chapter 3: BATTERY GUIDE
CHAPTER3:BATTERYGUIDE

PRECAUTIONS

Observe the following general battery warnings:
n As batteries contains flammable substances such as lithium or other organic solvents, they may
cause heating, rupture or ignition.
n Risk of explosion if battery is replaced with a battery of an incorrect type.
n Do not short circuit, disassemble, deform or heat batteries.
n Never try to charge a visibly damaged or frozen battery.
n Keep batteries out of reach of small children. Should a child swallow a battery, consult a phy-
sician immediately.
n Avoid direct soldering to batteries.
n When discarding batteries, insulate the + and - terminals of batteries with insulating/ masking
tape. Do not put multiple batteries in the same plastic bag.
n When improperly disposed, lithium batteries may short circuit, causing them to become hot,
burst or ignite.
n Store in a cool location. Keep batteries away from direct sunlight, high temperature, and high
humidity.
n Do not throw batteries into fire.


ROHSANDWEEE

In accordance with Directive 2011/65/EU on restriction of the use of certain hazardous substances in
electrical and electronic equipment (RoHS) and Directive 2002/96/EC on waste electrical and
electronic equipment (WEEE), Tele Radio AB strives to minimize the use of hazardous materials,
promotes reuse and recycling, and reduces emissions to air, soil and water. When a commercially viable
alternative is available, Tele Radio AB strives to restrict or eliminate substances and materials that pose
an environmental, health or safety risk.


GUARANTEE,SERVICEANDMAINTENANCE

The Tele Radio AB products are covered by a guarantee/warranty against material, construction and
manufacturing faults. During the guarantee/warranty period, Tele Radio AB may replace the product or
faulty parts. Work under guarantee/warranty must be carried out by Tele Radio AB or by an authorized
service centre specified by Tele Radio AB.

This is not covered by the guarantee/ warranty:
n Faults resulting from normal wear and tear
n Parts of a consumable nature
n Products that have been subject to unauthorized modifications
n Faults resulting from incorrect installation and use
n Damp and water damage
Maintenance:
n Repairs and maintenance must be carried out by qualified personnel
n Use spare parts from Tele Radio AB only
n Contact your representative if you require service or other assistance
n Keep the product in a dry, clean place
n Keep contacts and antennas clean
n Wipe off dust using a slightly damp, clean cloth
IMPORTANT! Never use cleaning solutions or high-pressure water.
-16 -

