Tele Radio Panther PN-R8-1 Installation instructions

Tele Radio Panther
SAFETY INSTRUCTIONS
CE-IM-PN-RX002-A01-EN
ARTICLE CODE: PN-R8-1, PN-T7-2
LANGUAGE: ENGLISH (ORIGINAL)
Standard settings
1 2
1
3
5
78
6
4
2

Thank you for purchasing a Tele Radio product
PN-R8-1, PN-T7-2
READ ALL INSTRUCTIONS CAREFULLY BEFORE MOUNTING, INSTALLING AND
CONFIGURATING THE PRODUCT.
These instructions are published by Tele Radio AB without any guarantee.These
instructions are solely directed towards qualied installers. The instructions may be
removed or revised by Tele radio AB at any time and without any further notice.
Corrections and additions will be added to the updated versions of the instructions.
The instructions that contain information on the installation and conguration of the
remote radio control unit on the machine are not intended to be passed on to the end
user. Only such information may be passed on to the end user, that is needed to operate
the machine correctly by radio remote control.
Tele Radio AB products are covered by a guarantee against material, construction or
manufacturing faults. During the guarantee period,Tele Radio AB may replace the product
or faulty parts with new. Work under guarantee must be carried out by Tele Radio AB
or by an authorized service centre specied by Tele Radio AB. Make sure that repairs and
maintenance are only carried out by qualied personnel. Use only spare parts from Tele
Radio AB. Contact your Tele Radio representative if you need service or support.The EC
declaration of conformity can be downloaded from our website.
©Tele Radio AB, 2011
TELE RADIO AB
Datavägen 21, SE-436 32 Askim. Sweden
Tel: [phone]
Fax: [phone]
www.tele-radio.com
2150

4
18
19
20
LED7 LED8
LED6
LED9
LED10
F
S
Relay 5 Relay 1 Relay 3Relay 2 Relay 4
5 1 2 3 4
+ -
12-24 V DC
CO NO NC
WR/5
CO NO NC
1 (on/off)
CO NO NC
2
CO NO NC
3 (kill)
CO NO NC
4 (Buzzer)
1 2 3 4 5 6 7 8 9
10
11
12 13 14 15 16 17
LEDs
TECHNICAL DATA RECEIVER
R8-1 (BASE BOARD)
1. Relay 1- on/off relay
2. Relay 5- work relay
3. Relay 2
4. Relay 3- kill relay
5. Relay 4- buzzer relay
6. Power supply connection
6-30 V DC
7. Relay LED 5
8. Relay LED 1
9. Relay LED 2
10. Relay LED 3
11. Relay LED 4
12. Power supply LED 6
13.Trabus programming connector
14.Terminal block for RS232
15. Function button (Cancel)
16. Select button (OK)
17. LED 8
18. LED 9
19. LED 10
20. LED 7
1
2
3
4
5
6
78910 11 13
12
14
15
16
17
18
19
20

5
Current consumption
RECEIVER MODEL SUPPLY VOLTAGE MAX. CURRENT CONSUMPTION
R8-1 12-24 V DC <200 mA.
Technical data
FUNCTIONAL RELAYS: 5 potential free* functional relays
NO/NC 8A ACI
NUMBER OF CHANNELS: 16
SIZE: 120 x 116 x 50 mm./
4.7” x 4.6” x 2”
WEIGHT: 400 grams/ 14 oz.
IP CLASS: IP66
FREQUENCY: 2405-2480 MHz.
* Potential free means that you need to supply voltage to get power out of a relay (e.g. via a
connection comb).
SYSTEM APPLICATION AREA
The Panther system is a simplex radio communication system that is
preferentially aimed towards professional industry, e.g. radio controlling of
winches and mobile applications.The functionality of the Panther systems
is as varied and versatile as are the needs of our customers.

6
LED INDICATIONS
LED INDICATIONS DURING START UP
1. All receiver LEDs lit up for 0.5 sec. to show that they are working.
2. Current settings are shown for 2 sec.
On relay LEDs 1-4:
Relay LED 1 OFF Continuous transmitting mode
ON Discontinuous transmitting mode
Relay LED 2 OFF Custom ID not enabled
ON Custom ID enabled
Relay LED 3 OFF Conguration ID not enabled
ON Conguration ID enabled
Relay LED 4 OFF Frequency scan on
ON Frequency scan off (xed frequency)
On LED 7, 8 and 9:
LED 7 ON Operating mode 1 (direct mode)
LED 8 ON Operating mode 2 (lifting mode)
LED 9 ON Operating mode 3 (LML mode)
LED INDICATIONS IN PROGRAMMING MODE
LED 7 red ON
LED 8 yellow ON
LED 9 green ON
LED 10 orange ON

7
LED INDICATIONS DURING OPERATION
LED 6 red ON Power to the receiver is on
OFF Power to the receiver is off
LED 7 red OFF No transmitter registered
ashes (slow) At least one transmitter is
registered and one transmitter is
logged in, but not transmitting.
ashes (quick) At least one transmitter is registered,
but not transmitting.
ON Valid radio packages from a registered
transmitter received.
ERROR INDICATIONS ON LEDS
LED 7
(red)
+ LED 8
(yellow)
ON Reading of production data failed.
Contact your representative.
LED 7
(red)
ON Radio module startup failed. Contact
your representative.
LED 8 ON A radio package not coming from a
Panther transmitter is received.
LED 8 + LED 9 ON A radio package from a transmitter in a
different mode (discontinuous or
continuous) than the receiver is
received.
LED 8 + LED 10 ON A radio package is received from a
transmitter that is not registered.
LED 9 ON A radio package is received, but the
radio signal strength (RSSI) is too low.
LED
10
ON A radio package is received, but the
conguration ID is not accepted.

8
TECHNICAL DATA TRANSMITTER
8-BUTTONS TRANSMITTER T7-2
Frequency: 2405-2480 MHz.
1 2
1
3
5
78
6
4
2
1. Rubber cover
2. STOP button
3. red LED 1
4. yellow LED
5. red LED 2
6. red LED 3
7. red LED 4
1
2
345
76
IMPORTANT! We recommend that the functionality of the STOP
button is being tested at a regular basis:At a minimum, when used for
200 hours.Test the STOP button by pressing and pulling it out.
STOP BUTTON TEST

9
Technical data T7-2 transmitter
NUMBER OF BUTTONS 8 x 2-step pushbuttons
BATTERIES 3 x 1.5V AA exchangeable
DEGREE OF PROTECTION IP65
NUMBER OF CHANNELS 16
SIZE 7.3 cm. x 17.8 cm./2.9 x 7 in.
(excl. rubber cover)
WEIGHT 250 g./ 0.55 lbs.
(excl. rubber cover, incl. batteries)
FREQUENCY 2405-2480 MHz.
Install batteries
1. Remove the battery cover (2 screws).
2. Put the batteries (3 x 1.5V AA
batteries) in.
3. Put back the battery cover (2 screws).
For optimum performance, use alkaline batteries.
The rubber cover
The transmitter comes with a removable rubber
cover that helps prevent the transmitter from bumps, dirt and dust.The
rubber cover can be removed and wiped off.
Remove the rubber cover
1. Loosen the rubber cover, starting at the top.
2. Lift the transmitter up out of the rubber cover.
Replace the rubber cover
1. Place the transmitter in the rubber cover, starting at the bottom.
2. Put the rubber cover back on the transmitter.
+
3 x 1.5V AA

10
STANDARD SETTINGS
• discontinuous radiotransmission
• no on/off function
The system will start transmitting as soon as the batteries are inserted,
the stop button is pulled out and a transmitter button is pressed. Radio
transmission will end when no transmitter button is being pressed.
DEFAULT STATE
START THE TRANSMITTER
TURN THE TRANSMITTER OFF
1. Pull out the stop button.
The transmitter transmits when a transmitter button is pressed.
1. Press the stop button.
NOTE! When the transmitter is active and the stop button is
pressed, all relays go off.
REGISTER THE TRANSMITTER IN THE RECEIVER
1-8 transmitters can be registered in the receiver.
1. Press the receiver Function button until red LED 7 lights up.
2. Press the receiver Select button until LEDs 1-5 light.
3. Press transmitter button 1, 1 step down, until LEDs 1-10 ash 3
times before going out.