TeleAdapt TA-7535 User manual

.HHSLQJ<RXU:RUOG&RQQHFWHG
Visit our website at: www.teleadapt.com
PowerHub USB Installation Guide_05/2015_REV-1

PowerHub USB™
|
TA-7535
.HHSLQJ<RXU:RUOG&RQQHFWHG

TeleAdapt PowerHub USB
|
Installation Guide
1
Table of Contents
2Products Covered By This Installation Guide
3PowerHub USB Part Numbers
4Important Safety Instructions
4Approval Information
8What Is Included In The Box
9Preparation For Installation
9Installation
12 Additional Information
12 Warranty
13 Contact Details

TeleAdapt PowerHub USB
|
Installation Guide
2Products Covered By This Installation Guide
The TeleAdapt PowerHub USB (TA-7535US) is a furniture power
distribution unit which provides 2 tamper resistant US NEMA
receptacles and 2 USB charging sockets (1 high power - 2.4A and
1 standard power -1A) all protected by a user resettable over
current device.
The use of tamper-resistant receptacles gives industry leading
protection against the accidental insertion of foreign objects into
the power sockets and provides enhanced safety for all users.
The TA-7535US is provided with 2 trims (Slimline black and
Slimline metallic) and a duplex power plug so the number of
available outlets in a room is not reduced when it is fitted.
Installation is simple as the TA-7535US only requires a single
connection to a US 120V/60Hz outlet, so fitting can be undertaken
by anybody who has a screwdriver and does not require a qualified
electrician.
PowerHub USB with Tamper-resistant Sockets (TA-7535US).
Duplex Plug.

TeleAdapt PowerHub USB
|
Installation Guide
3
PowerHub USB Part numbers:
TA-7535US-USN2
PowerHub USB with 2 metre rear power cable.
TA-7535US-USN3
PowerHub USB with 3.5 metre rear power cable.
It is also possible to supply the PowerHub USB with a straight,
simplex NEMA plug (instead of the right angled duplex NEMA
plug) if rear cabling needs to be pulled through a conduit. Please
contact TeleAdapt for additional information and availability.

TeleAdapt PowerHub USB
|
Installation Guide
4Important Safety Instructions
Read these instructions carefully before attempting any
installation. Follow all instructions and heed all warnings.
These instructions should be kept for future reference.
1This equipment must be securely attached to furniture in strict
accordance with these installation instructions.
2This equipment is designed for indoor use only.
3Only use with attachments and accessories as specified
by the manufacturer.
4The mains plug used to disconnect this equipment from its
power source must be readily accessible at all times.
5Ensure the power cord is uncoiled before installation.
6Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles and the point
where they exit from the equipment.
7The power cord must be plugged into a mains socket outlet
with protective earthing.
8Clean only with a dry cloth.
9Refer all servicing to qualified service personnel. Servicing is
required when the equipment has been damaged in any way,
for example if the power supply plug or cord is damaged,
liquid has been spilled or objects have fallen into the
equipment, the equipment has been exposed to rain or
moisture, does not operate normally or has been dropped
or damaged.

TeleAdapt PowerHub USB
|
Installation Guide
5
10 Unplug this equipment during lightning storms or when
unused for long periods of time.
11 Do NOT defeat the safety purpose of the grounded plug.
If the provided plug does not fit into your outlet consult a
qualified electrician to replace the obsolete outlet.
12 Do NOT install or use this equipment near water.
13 Do NOT expose this apparatus to rain or moisture.
14 Do NOT expose to dripping or splashing. No objects filled
with liquid such as vases shall be placed on the equipment.
15 Do NOT install near any heat sources such as radiators,
convection heaters or other apparatus such as amplifiers that
produce heat.
16 Do NOT exceed the maximum load of 10 amps.
Approval Information
The TA-7535US is UL listed for the USA and Canada and
conforms to UL962A and UL60950.

TeleAdapt PowerHub USB
|
Installation Guide
6Consignes de sécurité importantes
Veuillez lire attentivement ces consignes avant de
commencer l’installation. Veuillez suivre les consignes et
respecter toutes les mises en garde. Veuillez conserver ces
consignes pour référence ultérieure.
1Cet équipement doit être fixé de maniére sûre au mobilier en
stricte conformité avec ces instructions d’installation.
2Cet équipement est conçu pour une utilisation intérieure uniquement.
3Utiliser uniquement avec les fixations et lesaccessoires tels que
spécifiés par le fabricant.
4La prise de secteur utilisée pour débrancher cet équipement de
sa source d’a;imentatio doit toujours étre facilement accessible.
5S’assurer que le càble d’alimentation est déroulé avant l’installation.
6Protéger le càble d’alimentation pour éviter de marcher dessus ou
de le pincer, notamment au niveau des connecteurs, des prises de
courant et du point de sortie de l’équipement.
7Le càble d’alimentation doit être branché à la prise secteur équipée
d’une protection par mise à la terre
8Nettoyez à l’aide d’un chiffon sec uniquement.
9Toutes les opérations d’entretien doivent étre effectuées par le
personnel de maintenance. Une intervention de maintenance
est requise quand l’équipement a été endommagé d’une façon
quelconque, par exemple si la finche ou le càble d’alimentation a été
endommagé (e), si un liquide s’est déversé ou des objects sont
tombés sur l’équipement, si l’équipement a été exposé à la pluie ou
à l’humidité, s’il ne fonctionne pas correctement, s’il est tombé ou a
été endommagé.

TeleAdapt PowerHub USB
|
Installation Guide
7
10 Débrancher cet équipement en cas d’orage ou de non
utilsation prolongée.
11 Ne PAS altérer le dispositif de sécurité de la prise à terre. Si la
fiche fournie n’est pas adaptée à votre prise, consulter un
électrcien qualifié pour remplacer la prise obsoléte.
12 Ne PAS installer ou utiliser cet équipement près de l’eau .
13 Ne PAS exposer cet appareil à la pluie ou à l’humidité .
14 Ne PAS exposer l’appareil aux éclaboussures et aux gouttes
d’eau. Ne pas placer sur l’équipement d’objet rempli d’eau
comme un vase.
15 Ne PAS installer l’équipement à proximité d’une source de
chaleur comme un radiateur, un convecteur ou tout autre appareil
comme un amplificateur gènèrant de la chaleur.
16 Ne PAS excéder une charge maximum de 10 amps.

TeleAdapt PowerHub USB
|
Installation Guide
8What Is Included In The Box
Classic Trim
1 X PowerHub USB Main Unit with Power Cord and Duplex Plug.
1 X Black trim.
2 X Metallic trim.
4 X Fixing screws.
1 X Installation Guide.

TeleAdapt PowerHub USB
|
Installation Guide
136mm (max)
5.35in
73mm (max)
(2.87in)
50mm (min)
(1.97in)
65mm (min)
(2.56in)
Front of
furniture
Cutout
Rear of
furniture
Preparation For Installation
The PowerHub USB is designed to be installed in furniture.
Ensure the location chosen for the equipment complies with the
requirements of the “Important Safety Instructions”.
A cutout will need to be made in the furniture, cutout dimensions are
given in the “Installation” section of this guide. Other than this the only
tools you will need are a medium sized cross head screwdriver.
The minimum hole size the US duplex plug can pass through is
56mm (2.2”) x 40mm (1.6”).
The PowerHub USB requires power from a standard 3-pin US 120V
outlet.
Installation
Before starting installation make sure you have read and understood the
“Important Safety instructions” on page 4-5 / 6-7 of this guide.
Step 1
Confirm the furniture cutout dimension to accommodate the PowerHub
USB is within the limits shown below. Note that in addition to the
minimum depth requirement of 65mm (2.56 in) there should also be at
least 50mm (1.97 in) clearance below the unit to allow cabling to exit
cleanly.
Furniture cutout dimensions
9

TeleAdapt PowerHub USB
|
Installation Guide
10 Step 2
Remove the PowerHub USB, trims and screws from the box.
Step 3
Thread the rear power cable through the cutout in the furniture.
Step 4
Lean the PowerHub USB on the bottom of the cutout in the furniture and
push it into the cutout by rotating it slightly
Fitting PowerHub USB through the Cut Out.
Rotate Push Back
Fix Screws and
Attach Trim
Step 4 Steps 5 and 6

TeleAdapt PowerHub USB
|
Installation Guide
11
Step 5
Fasten the 4 cross head screws to fix the PowerHub in the furniture.
Step 6
Align the selected trim (black or metallic) with the PowerHub USB
ensuring that the 2 small cutouts on the trim are on the bottom.
Press firmly and evenly to clip the trim into place.
Step 7
Finally insert the plug on the end of the rear power cable into an appro-
priate 120V mains outlet.
Installation is now complete.

TeleAdapt PowerHub USB
|
Installation Guide
12 Additional Information
Overload Protection
The PowerHub USB has overload protection which cuts power to the
front sockets and USB if an overload occurs.
Before resetting please make sure the equipment that caused the
overload is no longer connected.
To reset press the small button located just above the USB sockets
on the front of the unit.
USB Charging
The PowerHub USB provides 2 USB charging ports on the front of
the unit. The left hand USB is suitable for tablets and mobile phones
and can provide 2.4A at 5V. The right hand USB is suitable for
mobile phones and can provide 1A at 5V.
Removing the PowerHub USB from Furniture
If you need to remove the equipment for any reason, first ensure the
equipment is disconnected from the mains power source.
1. Unplug the PowerHub USB from the mains supply.
2. Use a medium flat blade screwdriver to release 2 clips on the
bottom of the trim.
3. The trim can now be gently removed by hand. Be careful not to
bend the trim excessively or it may deform or break.
4. Unscrew the 4 cross head screws and carefully withdraw the unit
from the furniture being careful not to damage any cables.
Warranty
Please see TeleAdapt “Sales Terms & Conditions” which are available
at http://www.teleadapt.com/teleadapt/ sales-terms-conditions.html

TeleAdapt PowerHub USB
|
Installation Guide
13
Contact Details
Americas
TeleAdapt Inc
1315 Greg Street
Suite 110
Sparks
NV 89431
USA
Tel: [phone]
Europe
TeleAdapt Limited
Axis 5
Rhodes Way
Watford
WD24 4YW
United Kingdom
Tel: [phone]
Middle East
TeleAdapt Limited
Dubai Media City
Thuraya Tower 1
Office 1008
PO Box 500344
Dubai
UAE
Tel: [phone]
Asia
TeleAdapt HK, Ltd
Unit G, 15/F, Block 2
Leader Industrial Center
No. 188-202 Texaco Road
Tseun Wan
Hong Kong
Tel: [phone]
Website
For information on other
TeleAdapt products designed
for the hospitality industry,
including specification
and cut sheet downloads,
please visit our website at:
www.teleadapt.com