Teletek electronics CA60Plus User manual

CA60Plus
Installation manual
WARNING
This manual contains information on limitations regarding product use and function and information on the
limitations as to liability of the manufacturer. The entire manual should be carefully read.

Contents
PART I. Installation of the CA60Plus alarm control panel............................................................3
1. CA60Plus alarm control panel....................................................................................................4
2. LED60 and LED61 keyboards...................................................................................................5
3. CA60Plus control panel inputs and outputs...............................................................................6
4. Connecting LED60 and LED61 keyboards...............................................................................7
5. Using the PGM1, PGM2 and PGM3 programmable outputs...................................................8
6. Using SIREN programmable output..........................................................................................8
7. Connecting sensors to CA60Plus control panel........................................................................9
8. Connecting the CA60Plus built-in digital communicator..........................................................11
9. Powering the CA60Plus control panel......................................................................................11
10. Installation of the voice dialer - VD60......................................................................................12
11. Proximity cards reader - PR62 - connection....................................................................................13
PART II. Programming the software parameters for CA60Plus alarm control
panel..........................................................................................................14
0. User codes in the CA60Plus control panel..............................................................................15
2. Zone programming...................................................................................................................16
3. Programming the PGM and SIREN programmable outputs...................................................20
4. Time periods............................................................................................................................22
5. Engineer parameters................................................................................................................24
6. Communicator parameters.......................................................................................................26
7. Programming Up/Down Load parameters................................................................................29
8. Programming the voice dialer - VD60..............................................................................31
9. CA60Plus test modes...............................................................................................................32
Supplement A LED61 keyboard for CA60Plus control panel......................................................35
Supplement B Default programming table..................................................................................36
Supplement C Additional information.........................................................................................39
Supplement D General connection scheme.........................................................................................42
Supplement E Example voice messages...................................................................................43

CA60Plus control panel Installation manual 3
PART I. Installation of the CA60Plus alarm control panel
The CA60Plus Alarm control panel was designed and tested in compliance with electromagnetic
compatibility standards.
The following recommendations need to be observed for the proper performance of the alarm station:
1. Ensure the alarm system is properly earthed (grounded)
2. Insulate the high and low voltage cables and use different input openings on the box.
3. Avoid any loops of connecting wires within the very box and in their passage over or under the
printed-circuit boarding.
4. Additional relays must not be placed in the CA60Plus Alarm control panel box as these may
generate electromagnetic interference when switched.
4.1. Use only relays with good insulation between contacts and the winding.
4.2. Relays, connected to outputs with an open commutator, must be designed to accom-
modate a 12 V DC driving voltage and an impedance at the winding greater than
400Ω.
5. The cable connecting the control panel and the keyboard is quadruple. It is strongly recom-
mended not to:
5.1. use this cable to make other connections – connect to a telephone line, Flash-lamps
control signals, sirens or relays.
6. Avoid channels or cable forms that contain high voltage cables when placing the connecting
cables. This is very important in cases where such cables are being used to power electric
motors, fluorescent lamps or triple-phase voltage. Where the above is not possible, use only
shielded cables, where the shield is grounded only in the alarm system box.

4 CA60Plus control panel Installation manual
CA60Plus alarm control panel metal box
1. CA60Plus alarm control panel
2
1
11
Unscrew (1)
Remove cover (2)
Fig.1a CA60Plus control panel plastic box
1
6
3
5
1
4
Battery
12V / 7 Ah
F - 0,63 A
Transformer
230 Vac 50 / 60 Hz
sec.: 17 V / 24 VA
1
Radio transmitter
2
RESET
F1 BATT
F3 AUX
F2 PGM
PROG
Communicator
LED
2A
1A
1A
1 - Mounting openings
2 - CA60Plus control panel
3 - Mains supply terminal and fuse
holder
4 - Signal cables openings
5 - Mains supply cable hole
6 - Self-security TAMPER button
Fig.1 CA60Plus control panel
EXPAND

CA60Plus control panel Installation manual 5
2. LED60 and LED61 keyboards
Fig.2 CA60Plus LED keyboard
a) Cover
123
456
789
0
ON PROG CLEAR ENTER
ARM
MEM
CLR ENT
0
12 3
45 6
78 9
PROG
DISARM
б) Bottom
1
1
1
2
1 - Mounting holes
2 - Cables hole
1
1
11
1
2
2
CA60Plus alarm control panel plastic box
Fig.1b CA60Plus control panel plastic box
7
8
6
6
6
6
6
6
5
4
3
2
2
2
2
Accumulator cable
1 - Center support
opening (behind PCB)
2 - S
3 - CA 864 control panel
4 - Mains power supply
terminal
5 - Main cable opening
7 -
8 - Tamper button for box
self-protection
upport opening
6 - Add. cable openings
Mains power supply
opening
Mains
transformer
50 / 60 Hz
15-25 V / 50VA
12V / 7 Ah
battery
Room for additional modules
Room for add. Modules
Use to fix
main power supply cable
F - 0,63 A
BATT
RESET
F1 BATT
F3 AUX
F2 PGM
PROG
Communicator
LED
2A
1A
1A
1
EXPAND

6 CA60Plus control panel Installation manual
3. CA60Plus control panel inputs and outputs
•AC - power supply from 17 V/24 V A mains transformer
•Earth – conductor to “EARTH”
•+AUX and -AUX - 13 V DC power supply to sensors consuming up to 1 А
•+PGM - 13 V DC power supply to additional devices consuming up to 1 А
•PGM1, PGM2 and PGM3 – programmable outputs
•SIREN – siren programmable outputs
•Z2, Z3, Z4, Z5 and Z6 – zone inputs; ( Z1 zone is at the keyboard)
•COM – total mass of the zones
•Аand В– connects the telephone line
•А1 and В1– connects the telephone device
•RED and BLACK – keyboard power supply
•GREEN and YELLOW – interface between the panel and the keyboard
•F1 - 2 Аbattery fuse
•F2 - 1 Аfuse for powering sensors, programmable outputs and keyboards
•F3 - additional device 1 Аmains fuse
•12 V, 7 Ah battery cables
•RESET – jumper for hardware RESET and default parameter recovery
•Communicator LED – LED for status indication of built-in digital communicator
•PROG – terminal for programming by the manufacturer
•EXPAND – terminal for expander modules (Voice dialer)
Fig. 3 nputs and outputsCA60Plus control panel i
BATTERY
12 V / 7 Ah
BATT
B1
A1
B
A
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
Z3
Z4
COM
Z5
Z6
COM
RED
GREEN
YELLOW
BLACK
RESET
F1 BATT
F3 AUX
F2 PGM
PROG
Communicator
LED
2A
1A
1A
EXPAND

CA60Plus control panel Installation manual 7
4. Connecting LED60 and LED61 keyboards
The producer has been equipped the LED60 Keyboard with a bundle of wires 20-cm long.
The producer has been equipped the LED61 Keyboard with two wires 10-cm long for zone connec-
tion and terminals for the bus connection. These terminals are marked with the respective colors.
The colors must be observed (see Fig. 4) when connecting the keyboards to the СА60Plus Control
Panel.
The LED60 and LED61 Keyboards zone cables are white and black in color. The zone in the key-
boards does not have to be balanced. Where more than one keyboards are connected, the zone in each
one shall be monitored individually. Nevertheless, activating any keyboard zone shall be regard as an
activation of zone 1.
No more than eight keyboards (irrespective of their type) can be connected to one control panel. Each
keyboard must be assigned an individual address, by placing the jumper on the keyboard at its respective
place (see Fig. 5). The individual address ensures TAMPER event identification, whenever the keyswitch
of the respective keyboard is turned on.
LED60 and LED61 Keyboards addresses are assigned with the help of a jumpers. Following the table
(see Fig. 5) the respective address could be programmed. The JT jumper is shortened by default.
The JT jumper must be placed where only one keyboard has been connected. Where more than one
keyboards are connected, the JT jumper should be placed on the most distant one.
The cable connecting the LED60 and the LED61 Keyboards to the CA60Plus Control Panel must
be no longer than 250 m and have a cross-section of no less than 0.25 mm.
Fig. 4 Connecting LED keyboard to CA60Plus control panel
123
456
789
0
ON PROG CLEAR ENTER
YELLOW
WHITE
GREEN
RED
BLACK
BLACK
RED
GREEN
YELLOW
BLACK
CA60Plus control panel
terminals
ZONE 1
DETECTORS WIRES
ARM
MEM
CLR E NT 0
12 3
45 6
78 9
PROG
DISARM
Fig. 5 LED60 and LED61 keyboard jumpers
Addresses *
* The JT jumper must
be set in the most
far unit in the bus.
J0
1
0
0
0
0
1
1
1
J1
0
0
1
1
0
0
1
1
JT*
0
0
0
0
1
0
0
0
J2
0
1
0
1
0
1
0
1
0 = jumper is removed
1 = jumper is set
Rev1.3
JT
J0
J1
J2
TAMPER
CA60Plus
keyboard
Rev. 2.3
GREEN
YELLOW
RED
BLACK
BLACK
WHITE

8 CA60Plus control panel Installation manual
5. Using the PGM1, PGM2 and PGM3 programmable outputs
The СА60Plus Alarm Station PGM1, PGM2 and PGM3 outputs have a programmable active level.
This allows them to be used to transmit control signals towards external devices (e.g. a block siren input)
or to directly control low-powered external devices (e.g. relays, LED, etc.). The internal structure of all
PGMs is the same and is shown in Figure 6 a).
Figure 6 b) shows the connection of the relay and a light-emitting diode to the PGM. The active level
of this connection is low.
Fig. 6 b) Controlling light-emitting diode
relay using PGM1 and PGM2 outputs
and
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
CA60Plus
1k
RELAY
LED
Fig. 6 a) Internal structure of programmable
PGMx output
+12 VDC
1 kΩ
PGMx terminal
Permissible current:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
For SIREN output the
current supplied to GND
is up to 1 A.
6. Using SIREN programmable output
The СА60Plus Alarm Station SIREN output is designed to control a siren. The potential of the active
level of the SIREN output is not being controlled. In inactive state the output will have a potential of +12 VDC,
and in active state – GND. The internal structure is identical to the one shown in Figure 6 a). It should be
pointed out that the transmitter can pass through to GND electricity of up to 1 A.
Fig. 7 shows how to connect SR110E and SR120 sirens using the SIREN output.
Fig. 7 Controlling sirens using SIREN output
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
+12 V
-12 V
CA60Plus
SR110E
a) Connecting SR110E using
a double-wire
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
+12 V
GND
CA60Plus
SR120
BLK
The BLOCK jumper
in
.
SR120 must be
switched on
b) Connecting SR120 using
a double-wire
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
+12 V
GND
CA60Plus
SR120
BLK
The BLOCK jumper
in
.
SR120 must be
removed
c) Connecting SR120 using a triple-wire

CA60Plus control panel Installation manual 9
7. Connecting sensors to CA60Plus control panel
The security system is mounted with sensors with relay contacts. Fire alarm sensors supplied with
relay outputs can also be used.
Use the supplied 1 kΩresistors to balance the zones.The balancing resistors are installed on the last
sensor of the chain. The zones, which shall not be used, are terminated by way of the 1 kΩresistor at the
terminals of the CA60Plus Control Panel, irrespective of the chosen type of zone balancing.
After the initial power up of the station, the zone balance type has to be programmed. By default only
1 balancing resistor is used.
Figure 8 shows the possible options for connecting the sensors and for balancing the zones.
Figure 9 shows the connection between a keyswitch and a fire detector with a relay at the base.
The hardware implementation of zone 4 of the panel permits performance in pulse count mode. This
mode counts short pulses – 2 to 4 ms for a period of 20 seconds. The first pulse starts a 20-second
countdown during which pulses are expected to be received. Their number is assigned at Address 28 of
the engineer program. An alarm signal is emitted when this number is reached within the time of 20
seconds. Otherwise the pulse counter will be zeroed after the time of 20 seconds expires.
Activating the pulse count mode will automatically start when a number other than 0 is keyed in at
Address 28 of the engineer program.
b) Connecting Detectors with Two Balancing Resistors
1k
NC
RELAY 1
NC
RELAY 2
NC
RELAY n
NC
TAMPER 1
NC
TAMPER 2
NC
TAMPER n
1k
ZONE x
COM
Fig. 8 Options for connecting detectors to the CA60Plus control panel
а) Connecting Detectors with One Balancing Resistor
NC
RELAY 1
NC
RELAY 2
NC
RELAY n
NC
TAMPER 1
NC
TAMPER 2
NC
TAMPER n
1k
1k
ZONE x
TAMPER
ZONE
COM
COM
C) Connecting up to Four Detectors with Two Balancing Resistors
1k
NC
RELAY 1
NC
RELAY 2
NC
RELAY n
NC
TAMPER 1
NC
TAMPER 2
NC
TAMPER n
1k
ZONE x
COM
1k 1k

10 CA60Plus control panel Installation manual
Fig. 9 Connecting a key-switch and a fire detector with relay in the base
to a CA60Plus control panel
Connecting keyswitch with two balancing resistors
1k
NC
NC
1k
ZONE x
COM
Key-switch
Must be normally closed.
Tamper switch of the key-switch.
NC
Key-switch
Must be normally closed.
NC
Tamper switch of the key-switch.
1k
1k
ZONE x
TAMPER
ZONE
COM
COM
Connecting key-switch with one balancing resistor
Connecting a fire detector with a relay in the base
in scheme with two balancing resistors
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
+12 V
GND
NO
CA60Plus
Fire
detector
base
NC
COM
1k
1k
The programmable output
must be programmed
as Fire Reset and the active
status must be +12 VDC.
Connecting a fire detector with a relay in the base
in scheme with one balancing resistor
F2
B
AC
+AUX
-AUX
+PGM
PGM1
PGM2
PGM3
SIREN
Z2
COM
+12 V
GND
NO
CA60Plus
Fire
detector
base
NC
COM
1k
The programmable output
must be programmed
as Fire Reset and the active
status must be +12 VDC.

CA60Plus control panel Installation manual 11
9. Powering the CA60Plus control panel
The system should be powered-up only after it is installed and all necessary devices have been con-
nected – control panel, keyboard, sensors, etc.
In order to set the station to the producer’s default parameters place the Reset jumper on the CA60Plus
Control Panel.
Supply 220 V mains power. The keyboard emits a short sound signal and the light-emitting diodes on
the display blink.
Remove the Reset jumper.
Use the red (+) and black (-) cables to connect the battery to the station.
The normal status of the station (all sensors in the security system are inactive and there are no
violated anti-TAMPER chains) is indicated on the keypad by a continuously lit green READY light-
emitting diode. The station has now been programmed the producer default parameters.
All light-emitting diodes will blink and a sound signal will be heard where the keyboard is open or
incorrectly connected.
Where there is an open zone or an open TAMPER for any zone, the light-emitting diode for the
respective zone together with the MEMORY or TAMPER light-emitting diodes on the display will light
up.
NB! An open anti-sabotage chain (TAMPER) in the security system will sound the siren. To
stop the siren key in code 0000. The respective zone light-emitting diode remains perma-
nently lit whereas the TAMPER light-emitting diode will blink. Remove the failure – the
TAMPER light-emitting diode remains permanently lit. Key in code 0000 again to clear the
alarm event from the memory.
Any technical trouble in the panel will light up the Trouble indicator. To view these problems introduce
the 0000 manager code and single-press ENTER. The display will indicate a list of current problems. The
indications and their meaning are shown in Figure 11.
Fig. 11 TROUBLE mode indication
LED Technical trouble
1 No 220 Vpower supply
2 Battery low
3 Fuse burned
4 No telephone line
5 No communication available
6 Active TAMPER within the system
8. Connecting the CA60Plus built-in digital communicator
The telephone line is connected to A and B
terminals on the CA60Plus Control Panel with
no requirements to observe polarity (Fig. 10).
The telephone device is connected to A1 and
B1 terminals on the CA60Plus Control Panel
with no requirements to observe polarity (Fig.
10).
The parameters of the digital communica-
tor are engineer programmed.
It is not necessary to install additional com-
ponents if the built-in communicator is not to be
used.
B1
A1
B
A
}
Telephone line
Telephone device
}
Fig.10 Connecting the CA60Plus
built-in communicator

12 CA60Plus control panel Installation manual
RESET
PROG
EXPAND
SP MIC
REC
MSG
PLAY
MSG №
VD60
CA60Plus
BUSY
1
2 2
B1
A1
B
A
10. Installing the VD60 Voice Telephone Dialer into the СА60Plus
Fig. 12 Installing the VD60 Voice Telephone Dialer
The “VD60” Voice Telephone Dialer module supplements the СА60Plus Alarm Control Panel,
which serves to transmit alarm event messages to the user, under the form of eight pre-recorded voice
messages, of up to 5 sec. each. Two message types are supported – by zone or by event (see Supple-
ment E – Table with Sample Voice Messages).
Turn off the power supply in order to connect the PCB of the voice telephone dialer to the EX-
PAND socket of the CA60Plus Control Panel (1). Fix the PCB onto the pre-mounted plastic spacers
(2). The telephone line should be connected to terminals A and B of the СА60Plus Control Panel.
Polarity need not be observed.
The telephone device can be connected to terminals A1 and B1 of the СА60Plus Control Panel
with no need of observing polarity.
The voice dialer can simultaneously operate with the built-in digital communicator.
The dialer has one LED status indicator – PLAY/RECORD and BUSY, and one single digit LED
display indicating the number of the current message. Use the MSG key to switch-over between
messages. Use the PLAY key to reproduce messages when the REC jumper is turned off, or to
record when it is turned on. A speaker (8-16 ohms) for listening to recorded messages can be con-
nected to the SP socket.
The voice dialer parameters can be engineer programmable.

CA60Plus control panel Installation manual 13
11. PR62 proximity cards reader - PR62 - connection
The PR62 proximity card reader was designed to control security in the systems integrated within the
CA60Plus Control Panel. The excellent card reading distance, the triple color indications, supplemented by
the sound indicator, the integrated output, as well as the fine design, all make the PR62 any attractive supple-
ment to the security system.
The PR62 can be connected to the system bus of the CA60Plus together with the mounted keyboards.
Up to four proximity readers can be included within one security system. Programming the various addresses
onto the readers will provide identification by the TAMPER of each of these. The Table for Address Pro-
gramming is provided in Fig. 13.
The proximity-card enables to arm and disarm the system, as well as to control the electric lock via
integrated output. The internal structure, and the permissible output currents, are provided in Fig. 13.
It is possible that only proximity-card readers be included in a system without having an installed key-
board. In such systems this would hinder current programming of parameters and cards, as well as Log
Review and Technical Trouble indications. Portable LED60, LED61 or LCD62 type keypads can be used to
accomplish such tasks.
Up to 17 cards can be assigned to one security system – one card for each of the 16 users and one card
for the main user.
The main system user programmes the performance of the cards. Arming and/or disarming rights must
be assigned for the respective user code.
The user may not be designated a code combination. In such case the only means to control the
security system would be the proximity-card.
Фиг. 13 PR62 proximity cards reader connection scheme
Proxi CA62
TAMPER
LED
YELLOW
BLACK
GREEN
RED
PGM
J1
J2
JT*PR62 addresses*
JT* J1 J2
100
010
010
11
0
* The JTjumper must be set in
the most far unit on the bus.
Internal structure of built-in PGM
+12 VDC
1 kΩ
PGMx terminal
Permissable currents:
- from +12 V - up to 10 mA
- towards GND - up to 100 mA
The output activates for 2
seconds after the recognised
card is drown back.
Two color LED indicator
Signal cables
openings
Mounting openings
Lock
LED indication:
- green - the card is recogni-
sed or required action is done,
- red - the card is not recog-
nised or required action is
rejected,
- yellow (LED blinks) - ready.

14 CA60Plus control panel Installation manual
PART II. Programming the parameters for CA60Plus alarm
control panel
Carefully study this installation manual before programming the alarm station.
The respective parameters can be configured from a keyboard or remote control connected to the
system – a personal computer via a telephone using the UDLManager program.
Keyboard programming:
The CA60Plus Alarm System engineer parameters programming mode can be only begin when the
system is in disarmed mode.
Keying in the system engineer code will initiate the CA60Plus Alarm System programming mode for
the engineer parameters. After restoring the default parameters (RESET) the engineer code will remain
7777.
The respective Alarm System parameters can be programmed after a double-digit address is intro-
duced. Use the table with addresses in Supplement A and the detailed instructions about the addresses in
the remaining part of the manual.
The table with addresses provides the system RESET configuration.
A detailed description of the possible parameters, the keypad display indicators and the necessary
programming functions has been provided for each address.
Each address has been provided default configurations after a software or hardware RESET has been
carried out.
The information entered for each address can be confirmed by pressing the ENTER button.
When reviewing the programmed parameters it is recommended to exit any given address by single
pressing the CLEAR button. This function will leave the introduced parameters unchanged.
In case the programmer is disoriented in the engineer menu, it is recommended to exit the menu by
double clicking the CLEAR button and to begin programming the station parameters from the start.
Remote programming using the UDLManager program
To access a UDLManager program system requires a system password and a station program pass-
word. After restoring the default parameters these passwords will be the same and are 1234. In order to
provide access to the system from the central station enter the correct password of the central station at
Address 71.
A 24-hour period automatically begins after default parameters are restored during which the system
is in remote programming standby mode. Following this period, the “ring number” parameter is zeroed,
whereby the system will be locked for remote programming. This 24-hour period can be canceled by
introducing a telephone number for connecting to the central station at Address 70.
Detailed working instructions for the UDLManager program are provided in the built-in Help files.
The details listed in this manual apply to all parameters for remote system programming.

CA60Plus control panel Installation manual 15
ADDRESSES 02..16 USER CODE 2..16 ATTRIBUTES
The programming is the same as for Address 01.
DEFAULT: codes 02 to 16 have been assigned the attributes Disarm, Full ARM, Stay ARM, Force ARM,
LOG, BYPASS. However, no code combination has been introduced
0. User codes in the CA60Plus control panel
ADDRESS 00 MANAGER ACCESS TO USER CODE ATTRIBUTES
NO Manager access to user code authority is denied.
Light-emitting diodes 1 to 6 do not light up.
YES Manager access to user code authority is granted.
Light-emitting diodes 1 to 6 light up.
DEFAULT: YES
ADDRESS 01 USER CODE 1 ATTRIBUTES
USER CODE 1 attributes are assigned at this address. The user code can have
more than one attribute. Pressing a digital button with the respective number
activates the given attribute. The light-emitting diode with the number of the
pressed digit will light up to indicate the selection. Pressing the same digit again
will inactivate it and the light-emitting diode with the number of the pressed digit
will go out.
Only those light-emitting diodes, which correspond to the assigned attributes, will
remain lit at the end of the procedure. Pressing the ENTER button confirms the pro-
grammed attributes.
1 Disarm Authorizes this user code to Disarm the site.
2 Full ARM Authorizes this user code to Full ARM the site.
3 Stay ARM Authorizes this user code to arm those zones that have not been assigned a
STAY attribute.
4 Force ARM Authorizes this user code to arm with open zones for which a FORCE attribute
has been assigned.
5 Log Authorizes this user code to access log events.
6 Bypass Authorizes this user code to bypass zones in armed site.
DEFAULT:Disarm, Full ARM, Stay ARM, Force ARM, LOG, BYPASS

16 CA60Plus control panel Installation manual
2. Zone programming
ADDRESS 21 ZONE 1 TYPE AND ATTRIBUTES
This address includes two submenus. The zone type is set in the first one and the zone
attributes are set in the second one. Switching over from one submenu to the other is
done with the help of the arrows.
ZONE 1 TYPE SUBMENU
Only one type can be selected for a given zone. Press the digital button, which corre-
sponds to the number of the desired type. The indication is hexadecimal and is shown
in the table.
0 UNUSED The zone is not being used No light-emitting diodes light up
1 Entry/Exit Entry/exit zone Light-emitting diode 6lights up
2 FOLLOW Follow zone Light-emitting diode 5lights up
3 INSTANT Instant alarm zone Light-emitting diodes 5and 6light up
4 24h Burglar 24-hour instant alarm zone Light-emitting diode 4light up
5 FIRE 24-hour fire zone Light-emitting diodes 4and 6light up
6 PANIC 24-hour panic zone Light-emitting diodes 4and 5light up
7 TAMPER 24-hour tamper zone Light-emitting diodes 4, 5 and 6 lights up
8 MEDICAL 24-hour medical zone Light-emitting diode 3light up
9 SWITCH 24-hour zone switch type Light-emitting diodes 3 and 6 lights up
ZONE 1 ATTRIBUTE SUBMENU
Any one zone can be assigned more than one attribute. Pressing a digital button with
the respective number will activate a given attribute. The light-emitting diode with the
number of the pressed digit will light up to indicate the selection. Pressing the same digit
again will inactivate it and the light-emitting diode with the number of the pressed digit
will go out. At the end of this procedure, the light-emitting diodes, which correspond to
the assigned attributes only, will remain lit.
1 AUTOBYPASS Authorization for automatic Bypassing the zone after reaching the number of
activations per armed mode as set in address 27.
2 BYPASS Authorization to Bypass a zone.
3STAY The zone is not going to be armed in the STAY mode.
4 FORCE The zone will be bypassed if active when a Force type arm command is set.
5 DOUBLE DOUBLE KNOCK type zone
6 CHIME CHIME mode
DEFAULT: Entry/Exit type with BYPASS and CHIME attributes
Table 1 shows the types of zones and their attributes.
ADDRESS 20 TYPE OF ZONE BALANCING
The type of zone balancing is selected at this address. Every consecutive pressing of a
digital button alternatively changes the type of balancing. Display indications are given
in the table.
ALARM One balancing resistor. Light-emitting diodes 1 to 6 light up.
DUAL Two balancing resistors. Light-emitting diodes 1 to 6 do not light up.
DEFAULT:ALARM

CA60Plus control panel Installation manual 17
ADDRESS 22 ZONE 2 TYPE AND ATTRIBUTES
The programming is the same as for Address 21
DEFAULT: FOLLOW type with BYPASS and STAY attributes
ADDRESS 23 ZONE 3 TYPE AND ATTRIBUTES
The programming is the same as for Address 21
DEFAULT:INSTANT type with BYPASS and STAY attributes
ADDRESS 24 ZONE 4 TYPE AND ATTRIBUTES
The programming is the same as for Address 21
DEFAULT: INSTANT type with BYPASS and STAY attributes
ADDRESS 25 ZONE 5 TYPE AND ATTRIBUTES
The programming is the same as for Address 21
DEFAULT:PANIC type
ADDRESS 26 ZONE 6 TYPE AND ATTRIBUTES
The programming is the same as for Address 21.
DEFAULT: TAMPER type
ADDRESS 29 ENABLING AND DISABLING FOR INSTANT TYPE ZONES
Intrusion in any Instant type zone during exit time is allowed or disallowed at
this address. Enabling this working mode would reduce the probability for a
false alarm signal to be triggered off by mistake on behalf of the user.
INSTANT ENABLE NO Disallows intrusion in INSTANT type zones during exit type.
Light-emitting diodes 1 to 6 do not light up.
YES Allows intrusion in INSTANT type zones during exit type. Light-emitting
diodes 1 to 6 light up.
DEFAULT: NO
ADDRESS 27 NUMBER OF ACTIVATIONS PER ZONE FOR AUTO BYPASS
MODE
The number of activations in one arm mode, which have to be accomplished for
a zone with an assigned AUTO/BPS parameter, are entered at this address.
After reaching the indicated number of activations, the respective zone will be
automatically bypassed.
When disarmed and then again armed the respective zone will remain armed.
DEFAULT:6
ADDRESS 28 NUMBER OF ACTIVATIONS IN ZONE 4 IN PULSE COUNT
MODE
The number of pulses for zone 4 in Pulse Count mode are entered at this address.
Values of between 0 and 9 pulses can be entered here. The 0 value blocks the
Pulse Count mode and the zone can then function with the regular time for
detecting activation.
The working algorithm for zone 4 in Pulse Count mode has been clarified in
Item 7 on page 8.
DEFAULT:0

18 CA60Plus control panel Installation manual
INSTANT type An alarm zone which is active only when the site is armed. The zone operates
instantaneously and activates the programmable ALARM type outputs, the
SIREN output and the communicator.
The MEMORY light-emitting diode and the light-emitting diode for the respective
zone will light up when activated in armed mode. After disarming, these light-emitting
diodes will continue to be lit until the user code is entered or until the next arming.
Where the system is unarmed, the activation of the zone is indicated by the
blinking of the respective light-emitting diode for the zone for the time that the
zone remains open.
Violation of INSTANT type zones during Exit Time can be authorized at Address 29.
FIRE type Allows connecting 12 V fire alert sensors to the system. These should avail of
a normally closed relay output in inactive status.
Any activation of the zone will trigger off the SIREN output, the programmable
FIRE type outputs and the station communicator.
Activating this zone will cause the MEMORY light-emitting diode to blink and
the activated zone light-emitting diode to light up continuously, irrespective of
the working mode of the station.
The indication of the memory can be deleted by entering a legal user code,
manager code or during the next arming.
PANIC type Silent Panic – only the programmable PANIC type outputs and the station
communicator can be activated. The respective light-emitting diode blinks while
the zone is active. There is no memory indication. After a legal user code is
entered, the MEMORY light-emitting diode and the activated zone light-emitting
diode both light up continuously.
Sound Panic – the SIREN output, the programmable PANIC type outputs and
the station communicator are activated. The sirens are instantaneously activated
irrespective of the programmed time delay. Activating the zone will cause the
MEMORY light-emitting diode and the activated zone light-emitting diode to
light up continuously.
The indication of the memory can be deleted by entering a legal user code, a
manager code or during the next arming.
24h Burglar type An alarm zone, which is active, irrespective of the arm mode. The zone operates
instantaneously and activates the programmable ALARM type output, the SIREN
output and the communicator.
The MEMORY light-emitting diode and the light-emitting diode for the respec-
tive zone will light up when activated. After entering a legal code these light-
emitting diodes continue to be lit until the user code is entered a second time or
until the next arming.
Table 1. Types of zones and their attributes
Entry/Exit type Provides time to arm and disarm the site. After arming, the sensor, which was
triggered off in this zone, will not sound an alarm until the programmed EXIT
TIME expires.
No violation of the zone when in armed mode will sound an alarm before the
programmed ENTRY TIME expires.
A sound signal is activated from the keyboard buzzer during entry and exit time.
FOLLOW type An alarm zone which is active only when the site is armed. The zone operates
instantaneously and activates the programmable ALARM type outputs, the
SIREN output and the communicator.
Activating the zone during entry or exit time does not cause an alarm event.
The MEMORY light-emitting diode and the light-emitting diode for the respective
zone will light up when activated in armed mode. After disarming, these light-emitting
diodes will continue to be lit until the user code is entered or until the next arming.
Where the system is unarmed, the activation of the zone is indicated by the
blinking of the respective light-emitting diode for the zone for the time that the
zone remains open.

CA60Plus control panel Installation manual 19
SWITCH type Where this zone type is assigned, the respective panel input is used to transmit
the arming and disarming signal with the help of a keyswitch.
Each pulse at the input changes the system arm mode alternatively.
Arming is only possible in Full Arm mode. Arming will be anticipated only
when the system is ready – all zones are inactive.
AUTOBYPASS attribute Assigning this attribute to the respective zone enables automatic bypass in Armed
mode.
The zone will be automatically bypassed following the number of activations
indicated at Address 27 during one single arming.
Any arming will nullify the assigned number of activations of the previous arming.
This attribute is valid for the following zone types: Entry/Exit, Follow,
Instant, 24h Burglar
BYPASS attribute Assigning this attribute to the respective zone will authorize bypass of the zone
on behalf of the system user or manager.
This attribute is valid for the following zone types: Entry/Exit, Follow,
Instant, 24h Burglar, Fire, Panic, Tamper, Medical, Keyswitch
STAY attribute Assigning this attribute to the respective zone will authorize the respective Stay
mode zone arming.
This attribute is valid for the following zone types: Entry/Exit, Follow,
Instant, 24h Burglar
FORCE attribute Assigning this attribute to the respective zone authorizes automatic bypass of
the zone when in Force arm mode.
This attribute is valid for the following zone types: Entry/Exit, Follow,
Instant, 24h Burglar, Fire, Panic, Tamper, Medical
DOUBLE attribute Assigning this attribute to the respective zone authorizes DoubleKnock mode
performance in the zone.
A 3-min. time interval starts when the sensor in the zone is activated for the first
time in armed mode. An alarm event is registered should a second sensor
activation be recorded within this interval in the same or another zone.
An alarm event will also be registered if no zone is restored within 15 seconds
of the first activation of the zone sensor.
This attribute is valid for the following zone types: Entry/Exit, Follow, In-
stant, 24h Burglar
CHIME attribute Activating a disarmed zone for which this attribute has been assigned will sound
a specific signal from the keyboards.
This attribute is valid for the following zone types: Entry/Exit, Follow, In-
stant, 24h Burglar, Fire, Panic, Tamper, Medical, Keyswitch
Table 1. Types of zones and their attributes
MEDICAL type Assigning this zone type will set the programmable MEDICAL type outputs
active and will start the communicator. The activated zone light-emitting diode
will light up irrespective of the system status. The indication of the memory can
be deleted by entering a legal user code, manager code or during the next arming.
TAMPER type Activating this zone type triggers off the SIREN output, the programmable
TAMPER type outputs and the station communicator. Any activation of the
zone would trigger off a sound signal from the keyboard buzzer where the site
has been disarmed and the TAMPER siren output has been programmed as
SILENT.
The TAMPER light-emitting diode and the light-emitting diode for the respec-
tive activated zone will permanently light up continuously when the zone is
activated. The indication of the memory can be deleted by entering a legal
user code or manager code. A continuously open TAMPER is indicated by a
blinking TAMPER light-emitting diode.

20 CA60Plus control panel Installation manual
3. Programming the PGM and SIREN programmable outputs
ADDRESS 31 PGM1 PROGRAMMABLE OUTPUT
The events, which activate the programmable output, are programmed at this
address.
An arbitrary combination of events, which activate the programmable output, is
allowed. The output is activated upon the occurrence of any of the programmed
events and is restored when all programmed events are discarded.
Press a digital button, which corresponds, to a given parameter. The parameter
will have been selected when the light-emitting diode on the display with the
respective number lights up.
To switch from one parameter group over to another use the arrows.
FIRST GROUP PGM1 PARAMETERS
1 ALARM It is activated when Entry\Exit, Follow and Instant type zones are violated while
the system is in armed mode, or when the 24h Burglar type zone, irrespective of
the arm mode, is violated. Output is restored after a legal user code is entered
or following an interval of 1 min.
2 PANIC It is activated when the PANIC type zone is triggered or when PANIC is triggered
from the keyboard. Output is restored after a legal code is entered.
3 TAMPER It is activated when TAMPER is triggered off in any zone, when a TAMPER
type zone is triggered off or when TAMPER is triggered from the keyboard,
irrespective of the arm mode. It is restored after activation is discarded.
4 FIRE It is activated when a FIRE type zone is triggered. It is restored after a legal
code is entered.
5 FIRE RST It is activated for 4 sec. after a legal code is entered.
6ОN/OFF It is activated by a command to arm. Output is restored after disarming.
SECOND GROUP PGM1 PARAMETERS
1 MEDICAL It is activated when a MEDICAL type zone is triggered. Output is restored
after all MEDICAL type zones are restored.
2 PS/Bypass It is activated right after a zone has been designated to be bypassed or when the
zone has been assigned a Stay and Instant type arming. Output is restored after
disarming.
3 AC LOSS It is activated when there is a loss of the 220 V mains supply. ! If a delay for
the indication of the mains supply loss has been set (at Address 47), the
output shall be activated 30 minutes after supply loss! Output is restored
after the mains supply is restored.
4 BAT LOW It is activated when the battery voltage falls below 11 V, in case of damage to
the battery (BATT) fuse or if the battery is missing. It is restored after the level
of battery charge reaches a value greater than 12.5 V.
5 FUSE/NO TEL It is activated when a fault occurs in any of the AUX or PGM fuses, and/or
when a fault occurs in telephone line. It passes into inactive state when the fuse
and telephone line is restored.
6 POL +/- This attribute helps select the active level of the output. When “-“ is set (the
light-emitting diode is not lit) the active level is 0 V. At “+” the active level at the
output is 12 V.
DEFAULT:ON/OFF, POL “+”