Teletek electronics ECLIPSE 8 Mounting instructions

USER
OPERATION
MANUAL
ECLIPSE 8
ECLIPSE 16
ECLIPSE 32
ECLIPSE 99
(S.W. 3.xx)
ALARM CONTROL PANELS
Attention:
This manual contains information on limitations regarding product use and
function and information on the limitations as to liability of the manufacturer.
The entire manual should be carefully read.
The information in this manual is a subject to change without notice!

ECLIPSE 8/16/32/99 Series – User Operation Manual
2
Table of Contents:
1. GENERAL INFORMATION............................................................................................5
2. SUPPORTED KEYBOARDS .........................................................................................6
2.1 LED Keyboards........................................................................................................6
2.2 LCD Keyboards........................................................................................................6
2.3 Buttons Functionality................................................................................................7
2.4 Indication..................................................................................................................8
2.5 Sound Signalization.................................................................................................9
2.6 Directions for Operation with LED Keyboards..........................................................9
2.6.1 Special indication used in LED 8 and LED 16A keyboards...............................9
2.6.2 Special indication for reviewing of address number (LED 8 and LED 16A)....10
2.6.3 Programming by Manager..............................................................................10
2.6.4 Programming by User.....................................................................................10
2.7 Directions for Operation with LCD Keyboards........................................................11
2.8 Entering Text with LCD Keyboards........................................................................11
3. OPERATION INSTRUCTIONS ....................................................................................12
3.1 Arming with a Keyboard.........................................................................................12
3.1.1 Full Arming Mode............................................................................................12
3.1.2 Stay Arming Mode..........................................................................................12
3.1.3 Sleep Arming Mode........................................................................................12
3.1.4 Arming All Available Areas in the System.......................................................13
3.1.5 Viewing the Status of the Areas......................................................................13
3.1.6 Reviewing the Open Zones.............................................................................14
3.1.7 Changing the Arming Mode without Disarming...............................................15
3.2 Arming Via a Card Reader or BRAVO Remote Key Fob........................................15
3.2.1 Arming via Built-in Proxy Reader in Keyboard................................................15
3.2.2 Arming via Stand-alone Proxy Reader PR IT and Eclipse PR........................16
3.2.3 Arming via BRAVO RC Remote Key Fob.......................................................16
3.3 Disarming...............................................................................................................17
3.3.1 Disarming via keyboard..................................................................................17
3.3.2 Disarming via built-in card reader in a keyboard.............................................17
3.3.3 Disarming via stand-alone proxy reader.........................................................17
3.3.4 Disarming via BRAVO RC Key Fob................................................................17
3.4 Stopping the Sounders...........................................................................................18
3.5 Panic Buttons.........................................................................................................18
3.6 Ambush Code........................................................................................................18
3.7 Technical Troubles Review....................................................................................18
3.8 Checking the Bypassed Zones ..............................................................................20
4. USERS’ PROGRAMMING MENUS.............................................................................20
4.1 Changing own code...............................................................................................21
4.2 Memory LOG review by User.................................................................................21
4.3 Turning on the Chime signalization by User...........................................................22
4.4 Zone bypassing by User........................................................................................23
4.5 Adding Own Proxy Card.........................................................................................24
4.6 Deleting Own Proxy Card.......................................................................................25
5. MANAGERS’ PROGRAMMING MENUS.....................................................................25
5.1 Creating and Changing User codes.......................................................................27
5.2 Deleting User codes...............................................................................................27
5.3 Memory LOG review by Manager..........................................................................27

ECLIPSE 8/16/32/99 Series – User Operation Manual
3
5.4 Turning on the Chime signalization by Manager....................................................28
5.5 Zones bypassing by Manager................................................................................28
5.6 Engineer Access....................................................................................................28
5.7 Assigning User attributes.......................................................................................29
5.8 Associating Area numbers to User.........................................................................30
5.9 Entering of User names.........................................................................................31
5.10 Associating Timeslots to User..............................................................................32
5.11 Assigning Attributes for user proxy card...............................................................33
5.12 Registering a User card.......................................................................................34
5.13 Deleting a User card ............................................................................................34
5.14 Cloning Users ......................................................................................................34
5.15 Setting a function for “” or “A” button of BRAVO Key Fob.................................35
5.16 Setting a function for “B” button of BRAVO Key Fob............................................36
5.17 Setting the Time...................................................................................................36
5.18 Setting the Date...................................................................................................37
5.19 Blocking Remote Access via UDL........................................................................38
5.20 Assigning Rights for Remote Access...................................................................38
5.21 Sending a “Manual test” Message........................................................................39
5.22 Setting the Sound Level.......................................................................................40
5.23 Setting the intensity of illumination of the buttons................................................40
5.24 Scroll speed of messages in LCD keyboards.......................................................41
5.25 Entering Phone Numbers for the Eclipse VD Voice Dialler ..................................41
APPENDIX A - Table for Memory LOG Events.............................................................41
APPENDIX B – Special Symbols for Text Entering .....................................................44
APPENDIX C – VD/DTMF Operation Algorithm............................................................46
System Check List .........................................................................................................47
USER MAINTENANCE NOTES
To provide long-lasting and reliable work of your security system we recommend the
users to follow a few simple rules for maintenance:
1. Remove the protective transparent sticker from the LED or LCD display before starting
daily operations with the keyboard.
2. Always close the protective cover when the keyboard is not used. That will protect the
buttons from dust and dirt penetrating.
3. Weekly clean from dust the keyboards using a soft cloth. You can use also moist
cleaning cloths for plastic surfaces.
4. Do not use any abrasive detergents that can scratch the surface.
5. Do not sprinkle or pour water and other liquids on the keyboard.
6. Always use only alcohol-free cleaning detergents for cleaning the LCD display.
7. Before cleaning the LCD 32 Sensitive surface you can lock the sensitive buttons for 30
seconds with pressing at the same time the PRG button + right arrow button.

ECLIPSE 8/16/32/99 Series – User Operation Manual
4
GUARANTEE
The guarantee terms are determined by the serial number (barcode) of the electronic device!
During the guarantee period the manufacturer shall, at its sole discretion, replace or repair any defective product when it is
returned to the factory. All parts replaced and/or repaired shall be covered for the remainder of the original guarantee, or 6
months, whichever period is longer. The original purchaser shall immediately send manufacturer a written notice of the
defective parts or workmanship.
INTERNATIONAL GUARANTEE
Foreign customers shall possess the same guarantee rights as those any customer in Bulgaria, except that manufacturer
shall not be liable for any related customs duties, taxes or VAT, which may be payable.
GUARANTEE PROCEDURE
The guarantee will be granted when the appliance in question is returned. The guarantee period and the period for repair are
determined in advance. The manufacturer shall not accept any product, of which no prior notice has been received via the
RAN form at: https://teletek-electronics.com/en/ran-form.
The setup and programming included in the technical documentation shall not be regarded as defects. Teletek Electronics
bears no responsibility for the loss of programming information in the device being serviced.
CONDITIONS FOR WAIVING THE GUARANTEE
This guarantee shall apply to defects in products resulting only from improper materials or workmanship, related to its normal
use. It shall not cover:
- Devices with destroyed serial number (barcode);
- Damages resulting from improper transportation and handling;
- Damages caused by natural calamities, such as fire, floods, storms, earthquakes or lightning;
- Damages caused by incorrect voltage, accidental breakage or water; beyond the control of the manufacturer;
- Damages caused by unauthorized system incorporation, changes, modifications or surrounding objects;
- Damages caused by peripheral appliances unless such peripheral appliances have been supplied by the manufacturer;
- Defects caused by inappropriate surrounding of installed products;
- Damages caused by failure to use the product for its normal purpose;
- Damages caused by improper maintenance;
- Damages resulting from any other cause, bad maintenance or product misuse.
In the case of a reasonable number of unsuccessful attempts to repair the product, covered by this guarantee, the
manufacturer’s liability shall be limited to the replacement of the product as sole compensation for breach of the guarantee.
Under no circumstances shall the manufacturer be liable for any special, accidental or consequential damages, on the
grounds of breach of guarantee, breach of agreement, negligence, or any other legal notion.
WAIVER
This Guarantee shall contain the entire guarantee and shall be prevailing over any and all other guarantees, explicit or
implicit (including any implicit guarantees on behalf of the dealer, or adaptability to specific purposes), and over any other
responsibilities or liabilities on behalf of the manufacturer. The manufacturer does neither agree, nor empower, any person,
acting on his own behalf, to modify, service or alter this Guarantee, nor to replace it with another guarantee, or another
liability with regard to this product.
UNWARRANTED SERVICES
The manufacturer shall repair or replace unwarranted products, which have been returned to its factory, at its sole discretion
under the conditions below. The manufacturer shall accept no products for which no prior notice has been received via the
RAN form at: https://teletek-electronics.com/en/ran-form.
The products, which the manufacturer deems repairable, will be repaired and returned. The manufacturer has prepared a
price list and those products, which can be repaired, shall be paid for by the Customer. The devices with unwarranted
services carry 6 months guarantee for the replaced parts.
The closest equivalent product, available at the time, shall replace the products, the manufacturer deems un-repairable. The
current market price shall be charged for every replaced product.
STANDARDS AND CONFORMITY
The Eclipse Series control panels are designed according and with conformity to the European Union (EU) Low Voltage
Directive (LVD) 2006/95/EC and Electro-Magnetic Compatibility (EMC) Directive 2004/108/EC.
The CE mark is placed for indication that the Eclipse control panels comply with the requirement of EU for safety, health,
environmental and customer protection.
CERTIFICATIONS AND APPROVALS
Alarm Control Panel: Eclipse 8, Eclipse 16, Eclipse 32
EN50131-1:2006; EN50131-3:2009
EN50131-6:2017; EN50131-10:2015
EN50136-1:2012; EN50136-2:2013
Grade 2 Class I SP2
Alarm Control Panel: Eclipse 99
EN50131-1:2006; EN50131-6:2008
EN50131-3:2009; EN50136-1:2012
EN50136-2:2013; EN50131-10:2014
Grade 3 Class I SP2
Cert. No: TT-449/2019
Cert. No: TT-76/2018

ECLIPSE 8/16/32/99 Series – User Operation Manual
5
1. GENERAL INFORMATION
ECLIPSE Series are control panels providing security and management of small and
medium residential or office sites.
The ECLIPSE family includes:
ECLIPSE 8 for management of small sites up to 8 zones organized in 1 common
area and for up to 8 users.
ECLIPSE 16 for management of small to medium sites up to 16 zones organized in 3
independent areas and for up to 32 users.
ECLIPSE 32 for management of medium sites up to 32 zones and 8 independent
areas and for up to 64 users.
ECLIPSE 99 for management of large sites up to 99 zones and 16 independent
areas and for up to 99 users.
In ECLIPSE Series control panels are available two types of users: Managers and
Regular users of the system. The Managers have extended rights for programming of
special system menus and the regular users have limited rights for operation with the
system.
Manager of the system can be every user, who has been granted manager rights. User 1
is the Chief Manager and his/her rights cannot be changed. The users can be granted
manager rights by the Engineer of the system, as well as by another Manager of the
system with programming rights.
The Manager programming is structured as text menus or 2-digit addresses*.
The User programming is structured as text menus 1-digit address*.
*Note: The type of programming is set from the engineer on the site.
Entrance in the manager menu is possible even when the system is armed, but there are
certain limitations, for example zones cannot be bypassed in armed mode.
It is possible to enter in manager programming menus from several keyboards at a time
using the same manager access code.
The structure of Manager and User programming menus is as follow:
Note: The presented into this manual information is for User operation via LCD keyboard
and set text menus, or LED keyboard.
Before starting any programming or changing the system parameters,
you should read carefully the provided detailed information for each
menu and make sure that you understand the descriptions.
Keep this manual in safe place and refer to the instructions every time
you are about to program or change system parameters and settings.
Access
Code
Submenu/
Settings
Programming
menus
Select text menu or
enter an address
Confirm

ECLIPSE 8/16/32/99 Series – User Operation Manual
6
2. SUPPORTED KEYBOARDS
According your system configuration, you may use one of the following keyboard models:
Keyboard
Display
Areas
Zones
Card reader
LED 8
LED
1
8

LED 16A
LED
3
16

LED 32
LED
8
32
(option)
LCD 32
LCD
Up to 16
Up to 99
(option)
LCD 32S
LCD
Up to 16
Up to 99

2.1 LED Keyboards
LED 8
LED 16A
LED 32
Front view of ECLIPSE LED keyboards with open protective cover. The keyboards are
equipped with LED information display and rubber keypads for operation.
2.2 LCD Keyboards
LCD 32
LCD 32 S
Front view of ECLIPSE LCD keyboards, where LCD 32 is with open protective cover. The
keyboards are equipped with LCD text display. LCD 32S is with sensitive buttons and
built-in card reader.

ECLIPSE 8/16/32/99 Series – User Operation Manual
7
2.3 Buttons Functionality
Button
Function
Description
ENTER
Confirmation of the entered data. For LED 8 and LED 16A
keyboards: Use the button to review the memory log file, the
system troubles and the bypassed zones – the respective
system LED is blinking during the review.
CANCEL
Canceling the entered parameters; exit from a programming
mode.
FULL ARM Quick button for Full Arming Mode.
DISARM
Disarming the system. The button has a special function in
text entering mode – deletes the current symbol and moves
the cursor on one position to the left (like Backspace button on
a standard PC keyboard).
STAY ARM
Quick button for Stay Arming Mode. The button has a special
function in text entering mode – shifting between small and
capital letters.
SLEEP
ARM
Quick button for Sleep Arming Mode.
PRG Entry in Manager and User programming modes.
BYPASS*
Bypassing zones. The button lights on permanently if there
are bypassed zones in the system. The button is blinking
during the bypassed zones review.
TROUBLE*
Reviewing the system troubles. The button lights on
permanently if there are system problems. The button is
blinking during the system troubles review.
AREA А
LED 16A: The button performs arming/disarming of AREA А.
AREA В
LED 16A: The button performs arming/disarming of AREA В.
AREA С
LED 16A: The button performs arming/disarming of AREA С.
MEMORY*
Reviewing the memory events log file. The button lights on
permanently if there are memory events. The button is blinking
during the memory events review. The button has a special
function in text entering mode – entering of special symbols.
Scroll
arrows
Arrows for moving the cursor on the left and on the right in
programming mode.
0 - 9
Digit
Buttons
Digital buttons for entering parameters, codes, etc.
* Note:The functionality of BYPASS, TROUBLE and MEMORY buttons for LED8 and
LED16A keyboards is accessible through the manager and user menus only with the
same LED indication on the display.

ECLIPSE 8/16/32/99 Series – User Operation Manual
8
2.4 Indication
Button/LED
Color
Description
Red The area is in FULL ARM mode.
Red The area is in STAY ARM mode.
Red The area is in SLEEP ARM mode.
Red
Permanently lit - there are bypassed zones in the system.
Blinking - review of the bypassed zones in the system.
Red
Permanently lit - there are system troubles.
Blinking - review of the system troubles.
Red
Permanently lit - there are recorded memory log events.
Blinking - review of the memory log events.
Red
Indication for bypassed zones in keyboards LED8 and LED 16A.
Permanently lit - there are bypassed zones in the system.
Blinking - review of the bypassed zones in the system.
Red
Indication for system faults in keyboards LED8 and LED 16A.
Permanently lit - there are system troubles.
Blinking - review of the system troubles.
Red
Indication for memory events in keyboards LED8 and LED 16A.
Permanently lit - there are recorded memory log events.
Blinking - review of the memory log events.
Green
The system is disarmed or only certain areas in the system are
armed.
Red
All used areas in the system are armed.
Blinking in programming mode.
White Permanently lit - power supply from the panel; lit off - no power
supply from the panel. Blinking in programming mode.
Areas:*
А, Вand C
A1 – A8
Off
The area is not used.
Green
Permanently lit - the area is disarmed.
Blinking - the area is ready to be armed after user code is
entered and selected arming type.
Red
Permanently lit - the area is armed.
Blinking - entry/exit time is running; showing the available areas
to disarm after a user code has been entered.
Zone
numbers* Red
Permanently lit - indication for trouble or when the bypassed
zones, system troubles or events are being viewed.
Blinking - indication for an open zone when the system is
disarmed.
*The indication applies only to LED keyboards

ECLIPSE 8/16/32/99 Series – User Operation Manual
9
2.5 Sound Signalization
All ECLIPSE Series Keyboards have sound signalization for occurring of different system
events. The sound signalization has 4 volume levels adjustable in menu
“5. KBD SETTINGS - 1. BUSSER LEVEL” (Address 90) from the Manager programming
menus.
Sound Signal
Description
Button
Single short beep indicating the pressing of a key.
Confirmation
Two long sound signals, indicating the system confirmation to
executed operation.
Cancel operation
A single long beep, indicating system incorrectly executed operation.
Entry time
Continuous beep, indicating intrusion into an entrance zone.
Exit time
Short beeps, indicating the system is armed and the user is required
to leave the entrance zone. Ten seconds before the exit time is over
beep frequency increases.
Technical
problem
Two short beeps at every 20 sec, indicating a technical trouble.
To stop the signalization, enter a valid used code and press in
sequence buttons ENTER and TRBL (in operation with keyboards
LVD32, LCD32S and LED32); or double press button ENTER (in
operation with keyboards LED8 and LED16A).
See also item 3.7. Technical troubles review.
Chime
Short beeps with subsequently increasing period, indicating intrusion
into a zone with an activated chime option.
Fire alarm
Three sound signals in sequence repeated every 5 seconds. That
kind of signalization shows activated fire detector in the premises.
2.6 Directions for Operation with LED Keyboards
LED 8, LED 16A and LED 32 are keyboards for management and programming with LED
displays. LED 8 shows information about 8 zones and manages 1 area. The display of
LED16A shows information about the first 16 zones and 3 areas of the systems, while the
display of LED 32 shows information about all 32 zones and 8 areas of the system.
The entrance of codes, addresses, and data is done via the digit buttons. For the different
arming modes fast buttons with the respective symbol are used.
2.6.1 Special indication used in LED 8 and LED 16A keyboards
LED
Indication
Description
Red The system is in manager or user programming mode.
Red
[O] is short from OPERATION – in programming mode.
Red
[V] is short from VALUE – in programming mode.
Green
The system is disarmed; normal operation mode.
Off
The system is armed or the system is not ready to be armed.
Not used in manager and user programming menus.

ECLIPSE 8/16/32/99 Series – User Operation Manual
10
2.6.2 Special indication for reviewing of address number (LED 8 and LED 16A)
With DISARM button the user can check the number of the current address during
manager or user programming.
You can use the button in the following way:
1. The symbols and are lighting on permanently together with a number of zone(s),
according the type of the programmed parameter. A blinking digit shows that parameter
which is in setting mode, and lighting on digit button shows the current set value for this
parameter.
2. To find out what is the number of the current ADDRESS, press the button. The
zone numbers 1 and 2 are lighting on, the zone 1 is blinking, and lighting on button shows
the first digit of the address number.
3. Press the right arrow button. The cursor will move one position on the right, zone 2
starts blinking and lighting on digit number shows the next number of the address.
4. Press the button again to step back in parameter setting mode.
Note: You can also leave the view mode and with single pressing the CANCEL button.
Recommendation:If you are not familiar in details with the programming menus write
down in sequence the digits (of lighting buttons) corresponding to the respective address
positions (zone numbers).
2.6.3 Programming by Manager
•LED 32:
After manager code is entered, a confirmation beep is heard from the keypad. Entrance in
programming mode by a manager is done by pushing the PRG ( ) button. Two digits are
lit on the keyboard display, while the “lightning” (white) and “padlock” (red) LEDs flash
only on the keyboard, which is being used for programming. The system expects entrance
of 2-digit code for programming by manager. When a digit button is pushed the
corresponding zone LED lights up. When the “0” button is pushed zone number 10 lights
up.
•LED 8 and LED16A:
After manager code is entered, a confirmation beep is heard from the keypad. Entrance in
programming mode by a manager is done by pushing the PRG ( ) button. Two digits
are lit on the keyboard display and the LEDs and are lighting on only at the
keyboard, which is being used for programming. The system expects entrance of 2-digit
code for programming by manager. The setting of parameters is with pressing the digit
buttons as the button corresponding to the set value is lighting on.
2.6.4 Programming by User
Users in the system do not possess manager rights. Every code with forbidden option 8
Manager (programmed by the manager of the system) is a user code.
•LED 32:
After user code is entered a confirmation beep is heard from the keyboard. Entrance in
programming mode by a user is done by pushing the PRG ( ) button. One digit is lit on
the keyboard display, while the “lightning” (white) and “padlock” (red) LEDs flash only on
the keyboard, which is being used. The system expects entrance of 1-digit programming
address by a user.

ECLIPSE 8/16/32/99 Series – User Operation Manual
11
•LED 8 and LED16A:
After user code is entered a confirmation beep is heard from the keyboard. Entrance in
programming mode by a user is done by pushing the PRG ( ) button. One digit is lit on
the keyboard display and the symbols and are lighting on only at the keyboard,
which is being used for programming. The system expects entrance of 1-digit
programming address by a user.
2.7 Directions for Operation with LCD Keyboards
The LCD 32 and LCD 32 Sensitive are keyboards for management and control with text
LCD displays.
To enter codes, addresses and parameters use the digit buttons. For arming the system
can be used neither the quick buttons with the respective pictograms, or to choose the
arming type from the screen scrolling with the arrows and confirmation with ENTER
button. Use the provided further on detailed descriptions of the all addresses in the
system. To exit the manager or user programming menu press CANCEL button several
times until return to main screen in normal operation mode.
Attention: If no action (pushing a button) is performed for 30 sec. after entering the
manager or user programming menu, the system automatically returns to the main screen
and is again in normal operation mode. Entrance in programming mode by a manager or
user is possible via more than one keyboard at the time even with the same code.
2.8 Entering Text with LCD Keyboards
The keyboard models LCD32 and LCD32 Sensitive support text entering including small
and capital letters, digits, punctuation marks and other specific symbols.
The regular letters and digits can be entered directly by the buttons. It is possible to enter
text up to 16 symbols including space. Use the STAY ARM button to enter capital letters
and button DISARM to delete a symbol. MEM button provides entering of special
symbols.
Tables for correspondence of the buttons:
Button
Letters, digits
Button
Letters, digits
0
_
0
5
j
k
l
5
1
1
6
m
n
o
6
2
a
b
c
2
7
p
q
r
s
7
3
d
e
f
3
8
t
u
v
8
4
g
h
i
4
9
w
x
y
z
9
Three versions of the keyboard display are available according the supported language:
Cyrillic, Greek and EU version. Note: The type of the display is placed on the sticker on
the back of the keyboard: CYR (supports Cyrillic, English, Turkish fonts), GR (supports
English and Greek fonts) or EU (supports English, Hungarian, Italian and Portuguese
fonts) – see Appendix B.

ECLIPSE 8/16/32/99 Series – User Operation Manual
12
3. OPERATION INSTRUCTIONS
3.1 Arming with a Keyboard
3.1.1 Full Arming Mode
Full Arm mode means that all zones in the armed areas are being protected. Full Arm can
be initialized after entering a valid user code or with quick access without code, when this
option is allowed in the menus for engineer programming.
Sequence of buttons for activation of “FULL ARM” mode:
With code
Quick arming
3.1.2 Stay Arming Mode
Stay Arm mode means that the user can remain in certain, already bypasses zones of the
protected areas. Stay Arm mode can be initialized after entering a valid user code or with
fast access without code, when this option is allowed in the menus for engineer
programming.
Note: Certain users may not be permitted to ARM the system in “Stay ARM” Mode.
Sequence of buttons for activation of “STAY ARM” mode:
With code
Quick arming
3.1.3 Sleep Arming Mode
Sleep Arm mode means that the user can remain in certain, already bypasses zones of
the protected areas. Sleep Arm mode differs from Stay Arm mode in that for some of the
areas it is initialized without exit time. In that case, the arming of the system is instant. Ask
your installer for more details about you own system.
Note: Certain users may not be permitted to ARM the system in “Sleep ARM” Mode.
Sequence of buttons for activation of “SLEEP ARM” mode:
With code
Quick arming
Area
Numbers
Exit
Time
Code
Exit
Time
Push for 2-3
seconds
Code
Area
Numbers
2 signals or
Exit Time
Push for 2-3
seconds
Area
Numbers
2 signals or
Exit Time
Area
Numbers
Area
Numbers
Exit
Time
Code
Push for 2-3
seconds
Area
Numbers
Exit
Time

ECLIPSE 8/16/32/99 Series – User Operation Manual
13
3.1.4 Arming All Available Areas in the System
The user can perform arming of all available for operation areas in system. According the
way of arming – with or without entering a user code – the number of the armed areas can
be different.
Attention: If your system operates under the requirements of EN50131 Grade2/3, you will be unable
to arm it in case of active troubles: Tamper, SysBus Error, Siren Fault, CommTRBL or memory event
for area. If you have troubles to arm the system and there is indication for a fault ask your local
distributer or installer for technical support.
With a user code
When using a code for arming, the user can arm at the same time only all associated to
its own code areas. The user can be allowed to operate with one, several or all areas in
the system – that depends on the programmed for the code in manager’s menu
“1. USERS - xx. USER - 03. AREAS” (Address 07).
Quick Arming (Without a user code)
When performing quick arming, without entering code, the user can arm at the same time
all available for operation areas in the system.
Sequence of buttons for activation of all areas in the system:
With code
Quick arming
Attention: To arm all areas, enter “0” for Eclipse 16/32 or “00” for Eclipse 99.
3.1.5 Viewing the Status of the Areas
The user can check-up what the arming status of every one available area is in the
system. The check-up is different and depends on the used control keyboard.
•LED Keyboards
When the system is armed the numbers of the armed areas are lit in red.
At LED 8 keyboard, the DISARM button is off, and the quick button of the used arming
mode lights on in red.
At LED 16A and LED 32 keyboards, the used arming mode is checked after entering a
valid code and area number.
Sequence of buttons for checking-up the area status:
Note for LED 16A Keyboard: The three area numbers are named A, B and C. The user
can check the area arming mode pressing the buttons with the respective area letter.
Arming
type
Code
Exit
Time
Push for 2-3
seconds
Exit
Time
Code
Area
Number
The quick button of the used
Arming type is on in red
Exit
Full
Stay
Sleep
Eclipse 99
Eclipse 99

ECLIPSE 8/16/32/99 Series – User Operation Manual
14
•LCD Keyboards
The status of the used areas is viewed with pressing of ENTER button. Note that the
“padlock” LED lights up in red only when all the used areas are armed. The “padlock” LED
lights up in green if at least one of the used areas is disarmed.
To check-up the areas status simple press the ENTER button (Eclipse 32 in the example):
The screen displays the area numbers with the current status for every one of them.
The description of the area status is as follows:
Status
Description
-
The area is disarmed and ready to be armed.
n
The area is disarmed and not ready to be armed.
f
The area is armed in FULL Arming Mode.
s
The area is armed in STAY Arming Mode.
S
The area is armed in SLEEP Arming Mode.
*
Entry/Exit time is running for the area.
A
Alarm event in the area.
F
Fire alarm in the area.
M
Memory event in still armed area.
m
Memory event in disarmed area.
Empty
The area is not used in the system.
3.1.6 Reviewing the Open Zones
In normal operation mode the numbers of all open zones in the system are displayed one-
by-one on the LCD screen or are blinking on the LED display.
Attention: Areas with currently open zones cannot be armed!
The User can filter the displayed information and to review only those zone numbers
which are associated to the area that has to be armed. The User can review only those
areas for which he has assigned rights to operate!
•LED Keyboards
The numbers of all open zones in the system are blinking. To review (filter) the zone
numbers associated to an area the User has to enter a valid code and area number. Only
the open zones for that area will proceed to blink and the area number is lighting on.
•LCD Keyboards
The numbers of all open zones in the system are displayed one-by-one on the LCD
screen. To review (filter) the zone numbers associated to an area the User has to enter a
valid code and area number. Only the open zones for that area will proceed to be
displayed as text messages.
The exit from the open zones review mode is with pressing CANCEL button or
automatically after 30 sec.
Exit
The status is viewed
under the area number

ECLIPSE 8/16/32/99 Series – User Operation Manual
15
3.1.7 Changing the Arming Mode without Disarming
This is an extra functionality for changing the current arming mode with other without
disarming before that. To use this feature, keep in mind that the following priority between
arming modes is adopted:
Priority
Arming
Description
1
Full
The Full arming mode cannot be changed with other arming.
2
Stay
The Stay arming mode can be changed to Full arming.
3
Sleep
The Sleep arming mode can be changed to Full or Stay arming.
Example: Areas 1-4 are in Full ARM mode, and 5-8 are in Sleep ARM mode. To change
the arming mode of AREA 5, do in sequence (Eclipse 32 in the example):
Note: Use the button “0” (Eclipse 16/32) or “00” (Eclipse 99) to change all areas from one
arming mode to another.
3.2 Arming Via a Card Reader or BRAVO Remote Key Fob
Arming with proximity card is possible when there is a stand-alone proxy reader or a
keyboard with built-in reader connected to the system. To arm the system, the user needs
to put the card over the reader but not further than 1 cm.
3.2.1 Arming via Built-in Proxy Reader in Keyboard
Depending on the arming options set in manager’s menu “1. USERS - xx. USER –
06. PROXY OPTIONS” (Address 10), only one mode of arming can be activated with a
proxy card. When the proxy reader is built-in in the keyboard it is located in the middle
between the MEMORY, TROUBLE, ENTER and “9” buttons.
When using LCD keyboard, after the proxy card is recognized, the numbers of the areas
and their current status are shown on the display.
When using LED keyboard, after the proxy card is recognized the numbers of the areas
that are ready to be armed are blinking in green.
The system will wait for the number of areas to be entered.
Sequence for arming with a built-in in keyboard proximity card reader:
Notes:
Use the button “0” (“00” for Eclipse 99) to arm all associated to the user code areas.
The built-in card reader in LCD 32 Sensitive keyboard is situated in the right bottom
corner on the front panel and it is marked with a “key” pictogram.
Code
Area 5
2 signals
Area
Numbers
2 signals
or Exit Time

ECLIPSE 8/16/32/99 Series – User Operation Manual
16
3.2.2 Arming via Stand-alone Proxy Reader PR IT and Eclipse PR
The User can arm the system via stand-alone proxy reader in one of the following arming
modes, which are programmed in advance from the system engineer:
- “Full ARM” – of all available areas in the system
- “MODE А” – a specific combination of arming modes for the used areas
- “MODE В” – a specific combination of arming modes for the used areas
• PR IT: To arm the system in one of the listed above arming modes, the User
has to place and hold the proxy card (or tag) in front of the stand-alone reader
(RF) and to follow the sound and LED indication. When the system is disarmed
the green LED is lighting on permanently.
- To arm the system in “Full ARM” mode, place the proxy card in front the
reader and wait for one sound signal and then remove the card. The RED LED
is lighting on - the system is in “Full ARM” mode.
- To arm the system in “MODE А”, place the card in front of the reader and wait for one
confirmation signal. Hold the card for 2 more seconds until a second sound signal is heard
and remove it. Wait the YELLOW LED to light on and place the card in front of the reader
again. After a confirmation sound signal remove the card. The YELLOW LED is lighting on
- the system is armed in “MODE A”.
- To arm the system in “MODE B”, follow the same steps described above. Wait the
BLUE LED to light on and place the card in front of the reader. After a confirmation signal
remove the card. The BLUE LED is lighting on - the system is armed in “MODE B”.
• Eclipse PR: To arm the system in one of the listed above arming
modes, the User has to place the card in the area and wait until a
confirmation signal is heard. Remove the card and in a 5 seconds
interval press a button for arming:
Button
ARMING
“Full Arming” – Lights on into red.
“Arming MODE А” – Lights on into yellow.
“Arming MODE B” – Lights on into yellow.
After the exit time is over the LED of the used arming mode is lighting on.
3.2.3 Arming via BRAVO RC Remote Key Fob
Attention: The Arming with BRAVO RC is available when an Eclipse WL wireless
expander is added to the system configuration.
Button
ARMING
Hold the button for 2-3 seconds to activate “Full Arming” for all areas.
According the programmed in manager’s menu
“1. USERS - xx. USER - 09. RC(A)Func.” (Address 21).
Note: Ask you installer for details about the arming modes set for your system.
Area for
placing the
proxy card

ECLIPSE 8/16/32/99 Series – User Operation Manual
17
3.3 Disarming
Every user can disarm only those areas associated for operation to its personal code.
Note: Certain users may not be permitted to disarm the system.
3.3.1 Disarming via keyboard
The user can disarm one, several or all areas at the same time.
Sequence for disarming via keyboard:
Notes: Use the button “0” for Eclipse 16/32 or “00” for Eclipse 99 to disarm all associated
to the user code areas.
3.3.2 Disarming via built-in card reader in a keyboard
Disarming with proximity card is possible and when there is a proxy reader built-in in a
keyboard. To disarm the system, the user needs to put the card in front of the reader but
not further than 1 cm.
When using LCD keyboard, after the proxy card is recognized, the numbers of the areas
and their current status is shown on the display.
When using LED keyboard, after the proxy card is recognized the numbers of the armed
areas blink in red.
The system will wait for the number of the areas to be entered.
Sequence for disarming via card reader:
Note: Use the button “0” for Eclipse 16/32 or “00” for Eclipse 99 to disarm all associated
to the user code areas.
3.3.3 Disarming via stand-alone proxy reader
• PR IT: Place and hold the card in front of the reader until a confirmation sound signal is
heard. Remove the card – the GREEN LED lights on – the system is disarmed.
• Eclipse PR: Place the card in front of the reader and wait for confirmation signal.
Remove the card and in a 5 seconds interval press a button for disarming.
3.3.4 Disarming via BRAVO RC Key Fob
Press and hold the button for 2-3 seconds to disarm the system.
2 signals
Area
Numbers
Code
Entry
time
Entry
time
2 signals
Area
Numbers

ECLIPSE 8/16/32/99 Series – User Operation Manual
18
3.4 Stopping the Sounders
A triggered alarm can be stopped by entering a valid user code or a valid user card placed
in front of the proxy reader.
Note: The user code must have assigned rights to operate with area where the alarm
event is triggered off the sirens.
3.5 Panic Buttons
By using a combination of buttons, the user can send an alarm signal without triggering
the siren off. To send an alarm signal:
• For “FIRE ALARM” signal, press and hold the 7+9 buttons for 2 seconds.
• For “MEDICAL ALARM” signal, press and hold the 4+6 buttons for 2 seconds.
• For “PANIC ALARM” signal, press and hold the 1+3 buttons for 2 seconds.
3.6 Ambush Code
Ambush code is a system code which is used to disarm the system, but it also sends an
“alert” signal to the monitoring station. It is used when the user is forced to disarm the
system.
The Ambush code is formed by increasing the last digit of the user’s personal code by 1.
If the last digit is 9, it is replaced by 0.
For example: Personal code: 4615 → Ambush code: 4616
Personal code: 4619 → Ambush code: 4610
3.7 Technical Troubles Review
In case of system fault the “TROUBLE” button lights on permanently. On the LCD
keyboards text message “Trouble [TRBL]” is displayed.
To review the system faults, press the “TROUBLE” button. In TROUBLE MODE viewing
the “TROUBLE” button starts blinking. To exit TROUBLE MODE, press “CANCEL” button
or wait 30 seconds for the system to leave this mode automatically.
For LED 8 and LED 16A keyboards the system faults are indicated with permanently lit
TROUBLE LED. To review the system faults, single press the “ENTER” button.
The indication for system fault will stop automatically after the fault is restored.
The system faults are displayed with permanently lit on number on the LED display and
with a text message on LCD displays. The text messages are displayed one by one or
can be scrolled manually with the arrows.
To stop the sound signalization for system fault, enter in sequence:
For LED 32/LCD 32/LCD 32S
For LED 8/LED 16А
User
Code
User
Code

ECLIPSE 8/16/32/99 Series – User Operation Manual
19
The indication for the technical troubles according the used keyboard is as follows:
LED 8
LED 32/
LED 16A
LCD 32/
LCD 32 S
Description
Control panel Eclipse
8
16
32
99
  1. AC Loss
The mains power supply is
lost.

 
2. Battery
Trouble
The accumulator battery is
discharged or missing.

 
3. Blown
fuse
Blown out fuse. 
  4. Comm.
TRBL
Telephone line (PSTN) or
digital communicator (GPRS)
is lost. Communication with
central Monitoring station
fails.
Sending of message
(PSTN/GPRS/LAN) is
impossible.



5. Tamper
Open tamper in system.
   
  6. Sysbus
err
System bus error. It could be
short circuit in the line or lost
device.

 
7. Fire line
Error
Fire Detector Loss or the fire
line is broken.

 
8. Siren
Fault*
Problem with connected siren;
no siren connected to PGM5.

Button
“1”

9. Invalid
clock**
The internal clock has to be
set to an actual time and date.

Button
“2”  10. WL
device
trouble.
Possible problems:
- Low battery charge of
wireless device;
- Wireless device lost;
- Dirty chamber of a wireless
fire detector.

Button
“3”
11. WL RF
jamming.
Radio signal jamming. 
Button
“4”
12. AUX
PSU
trouble.
Possible problems with power
supply of expander modules:
- The mains power supply is
lost;
- Problem with the backup
battery;
- Blown out fuse.


ECLIPSE 8/16/32/99 Series – User Operation Manual
20
3.8 Checking the Bypassed Zones
According the used keyboard, the indication for bypassed zones differs.
Keyboard
Indication and checking the bypassed zone
LED 8/
LED 16A
The BYPASS LED is lit. In order to check the bypassed zones, you need to
press the ENTER button once. The numbers of the bypassed zones are lit,
while the BYPASS LED blinks.
Note:The LED 8 keyboard has indication for bypassing 01 to 08, and LED
16A – for 01 to 16 zones. If there are bypassed zones out of their range
(Eclipse 32/99), they are not shown on the screen.
LED 32
The BYPASS button is lit. In order to check the bypassed zones, you need
to press the BYPASS button once. The numbers of the bypassed zones
are lit, while the BYPASS button blinks.
Note:The LED 32 keyboard has indication for bypassing 01 to 32 zones. If
there are bypassed zones out of its range (Eclipse 99), they are not shown
on the screen.
LCD 32/
LCD 32
Sensitive
The BYPASS button is lit. In order to check the bypassed zones, you need
to press the BYPASS button once. Information about the first bypassed
zone is shown on the display, while the other zones can be checked with
the arrow buttons, the BYPASS button blinks.
4. USERS’ PROGRAMMING MENUS
There are no default codes for ordinary users in the system. The Manager in the system
can set new codes and allow certain users to have manager rights (for ECLIPSE 32/99).
To enter user programming mode, enter in consecutive order:
* Code without manager rights.
Quick table for Users’ Programming Menu
Text Menus
Address
Number
Programming
parameter
ECLIPSE Control Panel
8
16
32
99
1. User Code Change
1
Changing own code




2. View Log
2
Memory LOG view




3. Chime
3
Chime Enable/Disable




4. Zone Bypass
4
Zone bypassing




5. User Card
5
Add/Delete own proxy card




Code*
Select a programming menu/
address number