Televes TOX Series User manual

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP
EN
Ref. 563805
QUICK INSTALLATION GUIDE
www.televes.com

Safety instructions
Caution Statements
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with a dry cloth.
7. Do not block any ventilation openings. Install in accordance
with the manufacturer’s instructions.
8. Do not install near any heat sources such as radiators, heat
registers, stoves, or other apparatus (including ampliers)
that produce heat.
9. Only use attachments/accessories specied by the
manufacturer.
10. Use only with the cart, stand, tripod, bracket, or table
specied by the manufacturer, or sold with the apparatus.
When a cart is used, use caution when moving the cart/
apparatus combination to avoid injury from tip-over.
11. Refer all servicing to qualied service personnel. Servicing
is required when the apparatus has been damaged in any
way, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or
moisture, does not operate normally, or has been dropped.
Warning
Apparatus shall not be exposed to dripping or splashing and
no objects lled with liquids, such as vases, shall be placed
on the apparatus.
Safe operation
Should any liquid or object fall into the equipment, please
refer to qualied personnel for service.
Safe installation
Ambient temperature should not be higher than 95°F.
Do not place the equipment near heat sources or in a highly
humid environment.
Do not place the equipment in a place where it can suer
vibrations or shocks.
Please allow air circulation around the equipment.
Do not place naked ames, such as lighted candles on or
near the product.
Simbology
Equipment designed for indoor use.
The equipment complies with the CE mark
requirements.
This symbol indicate the maximum and minimum
temperature limits at which the equipment shall be
used.
DECLARACIÓN DE CONFORMIDAD DECLARATION OF CONFORMITY DECLARAÇÃO DE CONFORMIDADE DECLARATION DE
CONFORMITE DICHIARAZIONE DI CONFORMITÀ DEKLARACJA ZGODNOŚCI KONFORMITÄTSERKLÄRUNG ΠΙΣΤΟΠΟΙΗΤΙΚΟ
ΣΥΜΜΟΡΦΩΣΗΣ FÖRSÄKRAN OM ÖVERENSSTÄMMELSE ДЕКЛАРАЦИЯ СООТВЕТСТВИЯ بيان المطابقة https://doc.televes.com

HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP
4
5
6
9
11
Description of connectors
Front view
LED indicators
Rear view
1.- ASI input
2.- ASI output
3.- Power connectors
4.- Ethernet connector
5.- Ethernet connector
6.- Programmer connector
7.- RF loop through input
8.- RF output
1.- YPbPr component input. Channel 1
2.- Closed Caption (CC) input. Channel 1
3.- Analog (L/R) audio input. Channel 1
4.- HDMI input. Channel 1
5.- SPDIF digital optical audio input. Channel 1
6.- SPDIF digital coaxial audio input. Channel 1
7.- SPDIF digital coaxial audio input. Channel 2
8.- SPDIF digital optical audio input. Channel 2
9.- HDMI input. Channel 2
10.- YPbPr component input. Channel 2
11.- Closed Caption (CC) input. Channel 2
12.- Analog (L/R) audio input. Channel 2
Front LED alarms
TEMP
Color Internal temp Comment
Solid green Normal Safe
Slow blink orange High Warning
Fast blink red Very High Danger
CH1 – CH2
Color Channel status Comment
O Disabled Channel disabled
Solid green Lock Input locked and unit encoding audio/video.
Solid red Unlock Input unlocked and unit not encoding audio/video.
Blinking red Boot Unit starting up.
OUTPUT
Color Output mode Comment
Solid green Normal Output RF channel is ON, broadcasting audio/video (normal mode).
Slow blinking green Carrier wave, null, or muted Output RF channel is OFF or in an alternate signal mode.
Solid orange/red Normal Cong bitrate doesn’t t in output
LOOP
Color Output loop status Comment
Solid green ON Output loop-through enabled. Units may be daisy-chained using the internal combiner.
O OFF Output loop-through disabled. Units must be combined using an external combiner.
Back LED indicators A/V inputs Indicate the currently selected audio and video inputs and where the input signals should be connected.

Installation
1. Install all units in the rack and connect them as shown. Each P.S.U.
can power a maximum of 6 units, except in the case of using video
resolutions of 1080p, in which only 5 units can be powered.
HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP
Fig. 1
2. Connect the audio and video input signals to the back of the modules.
Fig. 2
3. If a network that provides IP addresses through DHCP is available,
connect the encoders to the network as shown in g. 3. If such a
network is not available, then a computer will need to be connected
as shown in g. 4.
HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP
Fig. 3
4. Power on the units.
HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR - Dual HDMI Component/IP to QAM/IP
DIRECT NETWORK
CONNECTION
IP value = 172.20.0.2
netmask = 255.0.0.0
gateway = 172.20.0.3
Fig. 4
5. Connect the programmer to each unit and set a unique number in
the “# ID” eld according to the order of installation of the units in
the rack.
HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP
DIRECT NETWORK
CONNECTION
IP value = 172.20.0.2
netmask = 255.0.0.0
gateway = 172.20.0.3
Fig. 5
6. Connect the programmer to a unit, usually the rst one, and read
the IP address.
Each unit can work as a master controller for the other units. All units
can be congured by connecting to only one.
HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP HDMI ENCODER/MODULATOR -Dual HDMI Component/IP to QAM/IP
Fig. 6
7. If a network was connected in Step 3 then proceed to step 8. If not,
set the address of you computer as follows:
IP value = 172.20.0.2
netmask = 255.0.0.0
gateway = 172.20.0.3
NOTE: The default factory conguration of the units has an IP address in
this range (it should be dierent for each unit). If a unit was ever
provided an address before, manually or through DHCP, this unique
address may no longer exist. Resetting to IP factory defaults, will
return the original unique private address though.
8. In your web browser, enter the IP address from Step 6 as the URL.
A login prompt will appear. By default the parameters are:
Login: encoder
Password: encoder

The Status > Summary page ( g. 7) should appear as the rst page.
This provides a summary of all the units installed in the network and the
units will be sorted by the number entered in Step 5.
Fig. 8 shows an example of a detailed status page.
9. Congure all units:
Select “CONFIGURATION”. This page has 5 options, INPUT, TRANSPORT,
OUTPUT, IP and NETWORK, shown in gures 9 to 14.
The last column of each conguration page is“Select”. Any changes made
will be saved only in the units with the “Select” option checked when
you click “Apply Selected” is applied to the ve tabs that exist under the
“Conguration” menu.
Some items have a choice of automatic conguration. For example, the
Network Conguration page allows you to change the number assigned
in step 5 of the installation process.
The “Auto” option will request conrmation if the parameters of all units
set in step 5 have been changed. The order will probably not correspond
with the position of the units in the rack.
9.1 INPUT
Conguration of the physical audio and video inputs. It
is possible to downscale the input resolution, modify the
video codec (MPEG-2 or H.264) or choose between frame
or eld encoding. If the input resolution is 1080p60/50 and
the video is being encoded in MPEG-2 it is necessary to set
the “Max Output Resolution” to 1080pHR. and frame/eld
encoding to “frame”. In this setup the output resolution will
be 1080P30/25.
Fig. 7 - Status > Summary
Fig. 8 - Status > Detailed
Fig. 9 - Input
Note: Resolution/Framerate will indicate the output video resolution only if it is dierent form the input one.

9.3 OUTPUT
Setting the RF output channel. The unit will restart if you switch
between QAM A and QAM B.
Fig. 11 - Output
9.4 IP
The unit can work in 3 dierent IP modes: Input, Output and
Disabled.
Input: The unit needs to be set in Input mode and have the IP
addresses, ports and standard (DVB or ATSC) congured.
Multicast and Unicast IP addresses are allowed.
These parameters can be modied on the IP tab (g. 12) and then
click “ Apply Selected”
Fig. 12 - IP
Fig. 13 - IP (2)
9.2 TRANSPORT
Changing the parameters of the output Transport Stream. The
TS ID, SID and VCNs of each service shall not overlap with those
of another service the same unit.
Fig. 10 - Transport

It is not possible to congure two equal IP adresses and ports,
the Web will warn you that it is not a valid conguration and will
not let you apply settings.
Pressing the “Select” button associated to each IP address, a
window with the available services will appear.
If no services are shown wait until the end of the scan.
Select the services to transmit through RF paying attention to the
free output bitrate and click on“Store Changes”.
Finally, to apply the conguration, click “Apply Selected”. The
selected services will appear in the “Transport” tab next to the
services of the physical inputs.
Output: To stream the services of the physical inputs via IP,
the unit must be set in Output mode and have the IP addresses,
ports, IP output type (SPTS or MPTS) and standard (DVB or ATSC)
congured. Multicast and Unicast IP addresses are allowed.
In SPTS mode, the physical input 1 will be streamed through the
IP1 and physical input 2 through the IP2.
In MPTS mode, the two physical inputs will be streamed through
a single IP.
If any of the physical inputs are disabled, the corresponding IP
service will not have transport.
9.5 NETWORK
Conguring network options. Both the IP address and the
networkmask may only be changed if DHCP mode is disabled
(g. 14).
10. Complete conguration window:
To change any encoder value from a single window, select
“CONFIGURATION”. Click on the name of the unit and the page shown
in gure 15 is displayed. From this page, you can modify any parameter
settings for the selected unit.
Fig. 14 - Network
Fig. 15 - Advanced conguration

- OUTPUT -
SELECT OUT
LEVEL
99
- OUTPUT -
SELECT OUT
LOOP MODE
LOOP
- UNIT -
IP
MODE
DHCP ON
- # ID -
0001
- TEMP -
NOW: 46 F
MAX: 86 C
- OUTPUT -
SELECT OUT
FREQ/CHAN
CATV CHANNEL
- OUTPUT -
SELECT OUT
CHANNEL
2 = 57MHz
QAM A QAM B
563805
- OUTPUT -
SELECT OUT
INTERLEAVING
<128.1>
* Next page
IP1 SERV
1/2
IPServ1
ON
ORIG. NAME
1/1 IP1
IPServ1
SID 1/1
IP1 IPServ1
00001 00003
INPUT 1/2
Selected
INPUT IP
Selected
(RX Mode Only)
IP MENU*
REMAP NAME
1/1 IP1
IPServ1
VCN 1/1
IPServ1
CVCT2
VCN 1/1
IPServ1
Major: 2
Minor: 3
- INPUT 1 -
VIDEO CONF>>
OUT: H.264
12.00 Mbps
- INPUT 1 -
MAX RESOLUT.
OUTPUT
AUTO
- INPUT 1 -
FIELD ENCOD.
OUTPUT
FIELD
- INPUT 1 -
- CC -
ON
-CHANNEL NUM-
MODE: CUCT 2
- INPUT 1 -
CUCT 2
MAJOR -> 2
MINOR -> 2
- INPUT 1 -
VIDEO CONF>>
PROF. LEVEL
AUTO(4.0)
- INPUT 1 -
CC: OFF
- QAM MODE -
QAM B
- OUTPUT -
SELECT OUT
MODULATION
256 QAM
- OUTPUT -
SELECT QAM
BAUD RATE
5.360 Kbaud
- OUTPUT -
SELECT OUT
MODE
NORMAL
- OUTPUT -
TS ID
0x0001
H.264 enconding only
QAM B only
QAM B 1.01.04
SW 1.04.0269
Menu ow chart
For programming Unit operation
Enable edit mode /
Position cursor
(in edit mode) /
Disable edit mode.
Change section /
Save parameters
(press and hold
for 3 sec.)
Change menu /
Modify value
(in edit mode)

PORT NUMBER
OUTPUT 1
01100
PORT NUMBER
OUTPUT MUX
01100
- OUTPUT IP -
OUTPUT 1
ENABLE
- STANDARD -
OUTPUT 1
ATSC
- STANDARD -
OUTPUT 1
ATSC
- STANDARD -
OUTPUT 2
ATSC
- INPUT IP -
INPUT 1
ENABLE
- STANDARD -
INPUT 1
ATSC
- OUTPUT IP -
OUTPUT MUX
ENABLE
- OUTPUT -
IP FORMAT
SPTS
- IP MODE -
RX MODE
- # ID -
0001
- N PACKETS -
OUTPUT 1
7
- N PACKETS -
OUTPUT MUX
7
-IP ADRESS -
OUTPUT 1
225.000.
001.001
-IP ADRESS -
INPUT 1
225.000.
001.004
-IP ADRESS -
OUTPUT MUX
225.000.
001.001
- RTP -
OUTPUT 1
ENABLE
- RTP -
OUTPUT MUX
ENABLE
- RTP -
OUTPUT 2
ENABLE
- OUTPUT IP -
OUTPUT 2
ENABLE
- N PACKETS -
OUTPUT 2
7
-IP ADRESS -
OUTPUT 2
225.000.
001.002
PORT NUMBER
OUTPUT 2
01200
SELECT
DEFAULT
SETTINGS
Hold key
PORT NUMBER
INPUT 1
1300
PORT NUMBER
INPUT 2
1400
- RTP -
INPUT 1
ENABLE
- RTP -
INPUT 2
ENABLE
- INPUT IP -
INPUT 2
ENABLE
-IP ADRESS -
INPUT 2
225.000.
001.005
RX MODE DISABLED
TX MODE
SPTS MPTS
- STANDARD -
INPUT 2
ATSC
IP menu
For programming Unit operation

Technical specications
Reference 563805
INPUTS
VIDEO Connectors 2 sets - 3x RCA for Video (Y, Pb, Pr)
AUDIO Connectors
2 sets - 2x RCA for Analog Audio (L, R)
2 sets - 1x RCA for Digital Audio
2 sets - 1x Toslink for Digital Audio (Optical)
VIDEO + AUDIO Connectors 2 sets - 1xHDMI
CLOSED CAPTIONING Connectors 2 sets - 1x RCA (CC in)
ASI
Connectors 1x BNC
Format DVB-ASI
Standard ETSI EN 50083-9
IP Connectors 2x RJ45 (Switch Gigabit)
Formats SPTS or MPTS (UDP/RTP)
ENCODING
PROFILE
VIDEO
Output Format MPEG-2 / H.264(4.0, 4.1, 4.2, 5.1, 5.2)
Input Resolution 480i, 480p, 576i, 576p, 720p, 1080i &1080p (1)
Supports auto-scan for input resolution
Input Framerate 50Hz, 60Hz (all input Resolutions), 24Hz (only 1080p Input Resolution)
Output Resolution Same as input (Auto) or maximum selected output resolution
Output Aspect Ratio 4:3, 16:9, and pass through
Output GOP 10, 12, 15, 16, 18, 20, 24 or 30
Output Transport rate Variable
Output Video bit rate Variable
AUDIO
Output format Dolby® Digital AC-3 or MPEG1 Layer 2
Output Sampling rate kHz 48, 44.1
Output bitrate Variable
CLOSED CAPTIONING Format EIA-608, EIA-708 (2)
OUTPUT
QAM
Connectors 1x “F” Female
Modulation standards ITU-A: 16, 32, 64, 128, 256, 512, 1024 QAM
ITU-B: 64, 256 QAM
Frecuency Range MHz 5 - 1002 (supports return path applications)
Channel plans CATV STD, T_CHANNELS, Broadcast, Frequency
Max output level dBmV +55 (+43 with loop-through)
MER dB >40 (typ)
Spurious dBc -60
Impedance Ω 75
I/Q Phase Error º <1
I/Q Amplitude Imbalance % <1
ASI Connectors 1x BNC
Format DVB-ASI
IP Connectors 2x RJ45 (Switch Gigabit)
Format SPTS or MPTS (UDP/RTP)
PSI PARAMETERS
Transport Stream ID Editable
Original Network ID Editable
Network ID Editable
Virtual Channel Number Editable
NIT Version Manual / Automatic
SDT Version Manual / Automatic
Network Name Editable
Service PID Editable
Service Name Editable
Service ID Editable
MONITORING / CONTROL
Local control Full conguration with LCD handheld programmer
Local monitoring
LOOP status LED
QAM status LED
TEMP status LED
CH1/CH2 status LEDs
Ethernet status LEDs
Remote monitoring Centralized web based remote control, management, alarms, and software upgrades
Control Daisy-chain integrated ethernet switch
GENERAL
Power supply V 24
Power disipation W <22.8
Operating Temperature ºF / ºC 32 to 95 / 0 to 35
The technical specications are dened for an ambient temperature of 35 ºC (95 ºF). It shall always be installed with forced ventilation.
(1) 1080p resolution is only supported with MPEG-4 video codec.
(2) For correct CC operation at the output, the maximum output resolution is set to “Auto”or the input and output resolution are both“i”or both“p”at the same framerate.

televes.com