Tyco Illustra Pro User manual

1
Tilt Mount Quick Start Guide
Illustra Pro 12MP Fisheye Camera
Illustra Pro 5MP Fisheye Camera
Illustra Pro Gen 2 12MP Fisheye Camera
8200-1306-02 C0

2
Notice
Please read this manual thoroughly and save it for future use before attempting to
connect or operate this unit.
The information in this manual was current when published. The manufacturer
reserves the right to revise and improve its products. All specifications are
therefore subject to change without notice.
Copyright
Under copyright laws, the contents of this manual may not be copied,
photocopied, reproduced, translated or reduced to any electronic medium or
machine-readable form, in whole or in part, without prior written consent of Tyco
Security Products. © 2020 Tyco Security Products. All rights reserved.
Customer Service
Thank you for using Tyco Security Products. We support our products through an
extensive worldwide network of dealers. The dealer through whom you originally
purchased this product is your point of contact if you need service or support.
Our dealers are empowered to provide the very best in customer service and
support. Dealers should contact Tyco Security Products at [phone] or
[phone] or at www.illustracameras.com.
Trademarks
The trademarks, logos, and service marks displayed on this document are
registered in the United States [or other countries]. Any misuse of the trademarks
is strictly prohibited and Tyco Security Products will aggressively enforce its
intellectual property rights to the fullest extent of the law, including pursuit of
criminal prosecution wherever necessary. All trademarks not owned by Tyco
Security Products are the property of their respective owners, and are used with
permission or allowed under applicable laws.
Product offerings and specifications are subject to change without notice. Actual
products may vary from photos. Not all products include all features. Availability
varies by region; contact your sales representative.
Manufacture
Tyco Security Products
6600 Congress Avenue
Boca Raton, FL 33487 U.S.A.

3
Table of Contents
What is in the Box....................................................................................................................................................4
Overview..................................................................................................................................................................4
Mounting the 12MP Pro Fisheye Camera.......................................................................................................5
Mounting the 5MP Pro Fisheye Camera.........................................................................................................6
Wall Box information.......................................................................................................................................7
IPFETILTMOUNT Illustra Pro Fisheye Tilt Mount Template...................................................................................9

4
What is in the Box
The box contains the following items:
1. Tilt Mount IPFETILT MOUNT
2. Quick Start Guide 8200-1306-02 and Tilt Mount Mounting Template 3610-0619-01
3. Installation kit which contains the following items:
Part Number
Description
Qty
5810-4091-120
stap,4.2X32,PHP,S304,P,7981C
4
2880-0073-01
ANCH,TGL,NYLON,#8-#10SCR
4
2880-0050
ANCH,PL,W/O SCR1''L,#10-12
4
5801-1081-120
M3x16mm PHP screws
2
Overview
The tilt mount is compatible with both 12MP Pro Fisheye indoor and outdoor cameras and Pro 5MP
Fisheye indoor cameras.
The tilt mount has a tilt of between 5 and 20 degrees. You can be use it with the following range of wall boxes:
•US Single Gang
•US Double Gang
•US Double Gang Wall Box
•US Octo Box
•Euro Box
•UK Single Gang Box
The tilt mount comes assembled with additional fixing screws and plastic wall plugs supplied. Tilt
angles of 5, 10, 15 and 20 degrees are demarcated on the slot on the tilt base for ease of
adjustment. You can perform assembly steps at the front of the camera so that disassembly of the
mount is not required. The tilt mount is intended for both indoor and outdoor installation.
Note: The housing on the Pro 5MP camera is not waterproof. The Pro 5MP camera is intended for
indoor use only.
Figure 1. Front view of mounted Fisheye camera Figure 2. Internal view of tilt mount

5
Mounting the 12MP Pro Fisheye Camera
To tilt mount the Illustra 12MP Pro Fisheye camera, complete the following steps:
1. To remove the front cover of the camera, use a Torx wrench to unscrew the two screws.
Figure 3. Site of screws on camera front cover.
2. Attach the camera base assembly to the tilt plate using the supplied screws.
Figure 4. Camera base assembly with tilt plate attached
3. Remove the plastic film from the lens.
4. Secure the camera base to the M3 threaded inserts that are fitted in the tilt plate, using the M3 fasteners
supplied in the installation kit. Ensure that the camera is rotated to a horizontal plane and that it is centered
on the tilt plate. Refer to Table 1 for information on securing the tilt plate to the wall box.
Figure 5. Screw sites on camera body
5. Thread the camera network cable into the opening on the back plate and align the top side of the camera
with the top of the back plate. For the Pro 12MP Fisheye Outdoor camera, Illustra recommends sealing the
cables as described in the Illustra Pro 12MP Fisheye Quick Start Guide.
6. To adjust the angle of the tilt on the tilt mount, loosen the locking screw at the bottom of the mount and
slide the lock to the desired point on the slot. Tighten the locking screw when the tilt mount is at desired
angle.
7. Replace the camera cover on the camera and secure it by tightening the two screws using the Torx wrench.

6
Mounting the 5MP Pro Fisheye Camera
To tilt mount the Illustra 5MP Fisheye camera, complete the following steps:
1. Unscrew the two M3 x 10 hex standoff screws on the tilt plate, using a Torx wrench.
2. Unscrew the three screws on the camera front cover using a Torx wrench, and remove the
camera front cover.
Figure 6. Site of screws on camera front cover
3. Thread the camera network cable into an opening on the back plate and align the top side of the
camera with the top of the back plate.
4. Secure the camera base to the M4 threaded inserts that are fitted in the tilt plate, using the M4
fasteners supplied in the installation kit. Ensure the camera is rotated to a horizontal plane and
that it is centered on the tilt plane. Refer to Table 1. Wall Box Information for information on
securing the tilt plate to the wall box.
Figure 7. Camera base assembly with tilt mount attached
Note: Remove the two M3 Hex Standoffs, circled in red, before fitting the camera.
5. To adjust the angle of the tilt on the tilt mount, loosen the locking screw at the bottom of the mount
and slide the lock to the desired point on the slot. Tighten the locking screw when the tilt mount is
at desired angle.
6. Replace the camera cover on the camera and secure it by tightening the two screws using the
Torx wrench.

7
Wall Box information
Table 1. Wall Box Information describes how to attach the tilt plate to different wall box options. Figure 8
displays the location of the hole patterns.
Figure 8. Tilt Mount with hole patterns

8
Box Type
Description
Sample Image
US Single Gang Box
Remove the tilt plate for fitting. Use two screws
to secure the tilt plate to the box.
Use hole pattern A.
US Double Gang Box
You do not need to remove the tilt plate. Use
two screws from the four screws provided to
secure the tilt plate to the box.
Use hole pattern B.
USA Double Gang
Wall Box
You do not need to remove the tilt plate. Use
two screws from the four screws provided to
secure the tilt plate to the box.
Use hole pattern F.
Euro Gang Box
Remove the tilt plate for fitting. Use four of the
screws provided to secure the tilt plate to the
box.
Use hole pattern C.
US Octo Box
Remove the tilt plate for fitting. Use the two
screws provided to secure the tilt plate to the
box.
Use hole pattern D.
UK Single Gang Box
Remove the tilt plate for fitting. Use two of the
screws provided to secure the tilt plate to the
box.
Use hole pattern E.
Table 1. Wall Box Information

9
IPFETILTMOUNT Illustra Pro Fisheye Tilt Mount Template
The tilt mount template below has been reduced 50%. The full size template document 3610-0619-
01Illustra-FE-Tilt-Mount_Template is included in the box and is available online.
Figure 9 Tilt Mount Template