Tenda W301A User manual

Distribuidor https://www.01seguridad.com.ar
W301A
300Mbps Wireless Access Point
User Guide

Distribuidor https://www.01seguridad.com.ar
Copyright Statement
is the registered trademark of Shenzhen Tenda
Technology Co., Ltd. All the products and product names mentioned
herein are the trademarks or registered trademarks of their respective
holders. Copyright of the whole product as integration, including its
accessories and software, belongs to Shenzhen Tenda Technology Co.,
Ltd. Without the permission of Shenzhen Tenda Technology Co., Ltd,
any individual or party is not allowed to copy, plagiarize, imitate or
translate it into other languages.
All the photos and product specifications mentioned in this manual are
for references only. As the upgrade of software and hardware, there will
be changes. And if there are changes, Tenda is not responsible for
informing in advance. If you want to know more about our product
information, please visit our website at www.tenda.cn.

Distribuidor https://www.01seguridad.com.ar
Contents
Chapter 1 Product Overview...............................................................1
1.1 Product Features....................................................2
1.2 Package Contents..................................................2
Chapter 2 Product Installation............................................................4
Chapter 3 Configuration Guide...........................................................5
3.1 Web Login...............................................................5
3.2 Setup Wizard ..........................................................6
3.3 Wireless Access Point (AP) Mode........................7
3.4 Bridge (WDS) Mode...............................................8
3.5 Running Status..................................................... 11
3.6 LAN Settings ........................................................13
Chapter 4 Wireless Settings .............................................................14
4.1 Basic Settings ......................................................14
4.1.1 Access Point (AP) Mode.........................14
4.1.2 Bridge (WDS) Mode.................................18
4.2 Security Settings ....................................................24
4.2.1 AP Security Setting.................................24
4.2.2 WDS Security Setting .............................32
4.3 Advanced Settings .................................................35
4.4 Access Control .......................................................37
4.5 Connection Status..................................................38
Chapter 5 SNMP Setting....................................................................39
5.1 SNMP Introduction...............................................39
5.2 SNMP Setting........................................................39

Distribuidor https://www.01seguridad.com.ar
Chapter 6 System Tools ....................................................................41
6.1 Password Change................................................41
6.2 Restore to Factory ...............................................42
6.3 Backup/Restore....................................................43
6.4 Time Settings........................................................43
6.5 Reboot System.....................................................45
6.6 Firmware Upgrade................................................45
6.7 Syslog ...................................................................46
Appendix I: Glossary.........................................................................48
Appendix II: TCP/IP Address Setting ...............................................50
Appendix Ⅲ: WDS Application Instances.......................................53

Distribuidor https://www.01seguridad.com.ar
1
Chapter 1 Product Overview
W301A is a wireless Access Point based on the latest IEEE802.11n
standard while at the same time being backwards compatible with
IEEE802.11b/g devices. Adopting the advanced “Multiple in and Multiple
out” (MIMO) technology, it can provide a maximum of 300Mbps stable
transmitting rate for wireless users. With appropriate Power over
Ethernet (POE) support, you only need to run one cable to the AP to
deliver both data and power. Ceiling mounted design and POE
technology make it couldn't be easier for family, enterprise, and hotel
users to extend wireless networks indoors. Unique Watchdog
technology makes AP working more stably and wireless network running
normally for a long time.
Wireless AP and WDS working modes support wireless AP, wireless
Repeater, wireless Point-to-Point (P2P) Bridge, and wireless
Point-to-Multipoint (P2MP) Bridge functions. Firstly, it can be used as a
wireless Hot Spot to enable the accesses of wireless users when in AP
mode. Secondly, it can be used as a Bridge to connect two or more
wired networks when it is in P2P or P2MP mode. Thirdly, it can also be
used as a wireless Repeater to expand your wireless network coverage
area.
Furthermore, 64/128-bit Wired Equivalent Privacy (WEP), WPA-PSK,
WPA2-PSK, WPA&WPA2, 802.1X Authentication, and MAC Address
filter are all supported to protect your data and privacy. Gigabit LAN port
provides you higher LAN transmission rate. SNMP and Web-based
management interface make configuration easier than ever.

Distribuidor https://www.01seguridad.com.ar
2
1.1 Product Features
Complies with the latest 802.11n and 802.11b/g standards
Supports AP and WDS working modes
Provides 300Mbps receiving and transmitting rate
MIMO technology uses signal reflections to increase 8 times
transmission distance of 802.11g standard and efficiently reduce
“dead spots”
One Gigabit Auto-negotiation LAN port supported for LAN
connection
POE and external power supported
SNMP and Web-based management interface
64/128-bit WEP encryption
WPA-PSK, WPA2-PSK, WPA&WPA2 encryption methods
Auto MDI/ MDIX
Wireless VLAN divisible for managing clients conveniently
Client's access limited
Watchdog designed to make device run stably
Supports auto wireless channel selection
Software controls the wireless signal on/ off and remotely controls
the wireless coverage area.
1.2 Package Contents
Please unpack the package and find the following items:
One W301AWireless AP
One Power Adapter

Distribuidor https://www.01seguridad.com.ar
3
Eight Screws
One User Guide
One Network Cable
Four plastic covers
If any of listed items are missing or damaged, please contact the Tenda
reseller from whom you purchased for replacement immediately.

Distribuidor https://www.01seguridad.com.ar
4
Chapter 2 Product Installation
You are recommended to install the product after configuring the
settings of W301A according to the guide in chapter 3. The following
steps take AP mode for example.
1. Use the included power adapter to power on the AP. You can also
use POE power supply or POE switch to power on the AP.
2. Connect one end of the network cable to the LAN port of W301A,
and another end to your Ethernet broadband, switch or PC.
3. Connect wireless adapter to W301A.
Please refer to the topology below:

Distribuidor https://www.01seguridad.com.ar
5
Chapter 3 Configuration Guide
3.1 Web Login
Connect to W301A via wired cable and configure 192.168.0.x(x ranges
2-254) as your PC’s IP address, and 255.255.255.0 as subnet mask.
(Please refer to the Appendix II for details on TCP/IP setting)
Launch Internet Explorer. In the address bar, enter the AP’s default IP
address, 192.168.0.254. Press Enter key and the login screen will
appear. Enter admin both in the user name and password field.
Click OK to enter the welcome page of the device.

Distribuidor https://www.01seguridad.com.ar
6
You can select “Running Status”, ”LAN Settings”, “Wireless Settings”,
“SNMP Settings” and “System Tools” on the left menu. Click “Next” to
enter the wireless working mode setup page. W301A supports two
working modes: wireless AP (AP), Bridge (WDS). Select a working
mode to configure the settings. For more details please refer to the
following chapters.
3.2 Setup Wizard
Click “Next” in the first page and the next page appears.

Distribuidor https://www.01seguridad.com.ar
7
On this page, you can select wireless AP or Bridge to adapt different
wireless access environment.
3.3 Wireless Access Point (AP) Mode
Select “Wireless Access Point (AP)” and then click “Next” to enter the
basic settings.
Picture 4
Fill in the following items according to the reminder information.
1. SSID: Set the SSID name of the device.
2. Channel: Select the wireless communication channel. The default
is channel 6.
After you finish the settings, click “Next” to enter the “Security Settings”
page as the picture below:

Distribuidor https://www.01seguridad.com.ar
8
“Security Settings” is used to encrypt the settings for AP and authorize
the wireless client to access the AP for security in wireless network.
Please refer to chapter 4.1.1.2 for detailed security setting
specifications.
After finishing the settings, click “Next” to finish settings as the picture
below.
3.4 Bridge (WDS) Mode

Distribuidor https://www.01seguridad.com.ar
9
Select “Setup Wizard” on the left menu and the working mode selection
interface will appear as the picture below.
Select Bridge (WDS) and then click “Next”. You will enter the WDS setup
page as the picture below.
Bridge (WDS) working mode includes: Point to Point Bridge (WDS P2P),

Distribuidor https://www.01seguridad.com.ar
10
Point to Multipoint Bridge (WDS P2MP), Wireless Repeater (Repeater).
Users can select the mode according to need. Please refer to Chapter
4.1.2 for detailed introduction.
Click “Enable Scan”. AP will scan the available wireless device nearby
automatically and display them under the list (see the picture below).
Select the AP which you need to bridge and click “Next” to enter the
security setup interface. On the other hand, you can input the MAC
address of wireless device which you want to bridge manually and
select the corresponding channel.

Distribuidor https://www.01seguridad.com.ar
11
After finish the settings, click “Next” to enter the “Security Setting” option
as the picture below.
“WDS Security Setting” is used to encrypt the AP and authorize the
device to establish bridge. Only when the passwords of the devices in
bridge are consistent, the communication can get through normally.
After finishing the settings, click “Next” and “Save” to finish settings.
3.5 Running Status
This page shows the wireless AP’s current status, including wireless
status, LAN status and system information.

Distribuidor https://www.01seguridad.com.ar
12
Wireless Status
It shows the current working status, including working mode,
wireless network mode, SSID, Channel, Encryption mode, etc.
LAN Interface information
It shows LAN IP obtain way, MAC address, IP address, subnet
mask, etc.
System information
It shows the device’s current software version, hardware version,
etc.

Distribuidor https://www.01seguridad.com.ar
13
3.6 LAN Settings
This section mainly deals with LAN’s basic settings.
Static IP ： The default IP address is 192.168.0.254. If necessary,
you can configure a new IP address, subnet mask and gateway
manually for the device.
Dynamic IP ： Automatically obtain IP address, subnet mask and
gateway from DHCP server. (Unless you have got permission to
obtain this information from the uplink connected device, otherwise,
it is not recommended to select this way).
Note: If the LAN IP address is changed, you need use the new IP
address to login the wireless AP’s Web interface next time.

Distribuidor https://www.01seguridad.com.ar
14
Chapter 4 Wireless Settings
This chapter introduces you wireless settings in two working modes:
Access Point (AP) and Bridge (WDS), including basic settings, security
settings, advanced settings, access control, and connection status.
4.1 Basic Settings
This period introduces you the basic settings in AP mode and WDS
mode.
4.1.1 Access Point (AP) Mode
In this mode, the AP will act as a central hub for accesses from wireless
to wireless, wireless to wired, wireless to WAN. The most important is to
provide a wireless client access such as wireless network adapter
access.
4.1.1.1 Application and Topology Plan
The AP mode can convert the wired transmission into wireless signals. If
you have one wired cable connecting to Internet, and want to access the
Internet via wireless signals connecting to your notebook computer, this
mode fits perfectly.

Distribuidor https://www.01seguridad.com.ar
15
4.1.1.2 Function Explanation
The basic setup page in Access Point (AP) working mode is as follows:

Distribuidor https://www.01seguridad.com.ar
16
Wireless Signal: Click “Disable” to shut all the wireless feature of
this AP; click “Enable” to open the wireless feature.
Network Mode：Select one mode from the following. The default is
11b/g/n mode.
11b mode：Allow the wireless client to connect with the device in
11b mode at the maximum speed of 11Mbps.
11g mode：Allow the 11g/11n-compliant client device to connect
with the AP at the maximum speed of 54Mbps.
11b/g mode：Allow the 11b/g-compliant client device to connect
with the AP with auto-negotiation speed, and 11n wireless client to
connect the device with 11g speed.
11b/g/n mode：Allow 11b/g/n-compliant client device to connect
with the AP with auto- negotiation speed. The maximum speed is