Ruijie RG-AP720-I User manual

RG-AP720-I Access Point
Quick Installation Guide

Copyright Statement
Ruijie Networks©2017
Ruijie Networks reserves all copyrights of this document. Any reproduction, excerption, backup, modification,
transmission, translation or commercial use of this document or any portion of this document, in any form or by any means,
without the prior written consent of Ruijie Networks is prohibited.
Exemption Statement
This document is provided “as is”. The contents of this document are subject to change without any notice. Please obtain
the latest information through the Ruijie Networks website. Ruijie Networks endeavors to ensure content accuracy and will
not shoulder any responsibility for losses and damages caused due to content omissions, inaccuracies or errors.

Preface
Thank you for using our products. This manual will guide you through the installation of the device.
This manual describes the functional and physical features and provides the device installation steps, hardware
troubleshooting, module technical specifications, and specifications and usage guidelines for cables and connectors.
Audience
It is intended for the users who have some experience in installing and maintaining network hardware. At the same time, it
is assumed that the users are already familiar with the related terms and concepts.
Obtaining Technical Assistance
Ruijie Networks Website: http://www.ruijienetworks.com/
Service Email: [email protected]
Technical Support: http://www.ruijienetworks.com/service.aspx
Technical Support Hotline: [phone]
Related Documents
Documents
Description
Configuration Guide
Describes network protocols and related mechanisms that supported by the
product, with configuration examples.
Command Reference
Describes the related configuration commands, including command modes,
parameter descriptions, usage guides, and related examples.
Symbol Conventions
Means reader take note. Notes contain helpful suggestions or references.
Means reader be careful. In this situation, you might do something that could result in equipment damage or loss of
data.

1 Packing List
Table 1-1 Packing List
Item
Name
Quantity
Unit
1
RG-AP720-I Host
1
Set
2
RG-AP720-I Plate Cover (White)
1
Piece
3
RG-AP720-I Access Point Quick Installation Guide
1
Copy
4
Product Warranty
1
Copy
5
Cross Recessed Pan Head Tapping Screw and Washer
Assemblies
4
Piece
6
Anchors
4
Piece

2 Product Image
Figure 2-1 Product Image of RG-AP720-I
Figure 2-2 Top View of RG-AP720-I
Figure 2-3 Bottom View of RG-AP720-I

Note:
①Built-in indicator
②Reset hole
③USB port
④Console port
⑤LAN2 port
⑥LAN1/PoE port
⑦48VDC power input

3 Button and LED Indicators
The LED indicator is on the top plate, and works after you power on the device.
You can also configure the Silent time on the AC/AP.
Table 3-1 Button and LED Indicators on RG-AP720-I in the Fit mode
Table 3-2 Button and LED Indicators on RG-AP720-I in the Fat mode
State
Frequency
Meaning
Off
N/A
The AP is powered off. Or the AP is in Silent mode (it can be
switched via software).
Fast blinking
green
3Hz
Initialization in progress.
Fast blinking
red
3Hz
Initialization is complete. The Ethernet link is down.
Fast blinking
blue
3Hz
Initialization is complete. The CAPWAP connection is being
established.
Solid blue
N/A
AP is operational. The CAPWAP connection is established. No
clients are associated.
Blinking blue
One flash every 3 seconds
AP is operational. The CAPWAP connection is established.At
least one client is associated.
Solid red
N/A
MCU is being upgraded.
Blinking red
Two flashes every 3 seconds
AP is being located.
State
Frequency
Meaning
Off
N/A
The AP is powered off. Or the AP is in Silent mode (it can be
switched via software).
Fast blinking
green
3Hz
Initialization in progress.
Fast blinking
red
3Hz
Initialization is complete. The Ethernet link is down.
Fast blinking
blue
3Hz
Initialization is complete. The Ethernet link is up.
Solid blue
N/A
AP is operational. No clients are associated.
Blinking blue
One flash every 3 seconds
AP is operational. At least one client is associated.
Solid red
N/A
MCU is being upgraded.
Blinking red
Two flashes every 3 seconds
AP is being located.

4 Installing RG-AP720-I
Ceiling Mount
1. Drill four 6 mm diameter holes (53 mm apart) on the ceiling. Tap wall anchors into the holes, and drive screws
through the mounting bracket into the anchors to fix the bracket.
Figure 4-1 Attaching the Mounting Bracket on the Ceiling
2. Align the square feet on the bottom of the AP with the mounting holes on the bracket.
Figure 4-2 Aligning the Square Feet with the Mounting Holes
Before mounting the AP on the bracket, you must first connect the Ethernet cables.
3. Slide the AP onto the bracket in the direction against the arrow on the mounting bracket until it clicks into place.
Figure 4-3 Mounting the AP on the Bracket

The AP can be installed in any of four directions on the mounting bracket depending on how you route your Ethernet
cables.
The square feet should fit easily into the mounting slots. Do not forcibly push the AP into place.
After installation, verify that the AP is securely fastened.
Wall Mount
4. Drill four 6 mm diameter holes (53 mm apart) on the wall with the arrow on the mounting bracket facing up. Tap wall
anchors into the holes, and drive screws through the mounting bracket into the anchors to fix the bracket.
Figure 4-4 Attaching the Mounting Bracket on the Wall
5. Align the square feet on the bottom of the AP with the mounting holes on the bracket.
Figure 4-5 Aligning the Square Feet with the Mounting Holes

Before mounting the AP on the bracket, you must first connect the Ethernet cables.
6. Slide the AP into the holes in the direction against the arrow on the mounting bracket until it clicks into place.
Note that “Ruijie”logo is on the upside.
Figure 4-6 Mounting the AP on the Bracket
Locking the Access Point
1) Loosen the screw on the mounting bracket to lock the AP to the bracket.
Figure 4-7 Loosening the screw

2) Align the square feet on the rear of the AP with the mounting holes on the bracket, slide the AP in the direction
against the arrow on the mounting bracket until it clicks into place.
Figure 4-8 Mounting the AP on the Bracket
Removing the Access Point
1) If the AP is locked, insert the key to the bottom of a lock slot, and drive the AP in the corresponding direction as
shown in Figure 4-9. If the AP clicks into place and the key cannot be pulled out, it indicates that the AP is unlocked.
If not, keep trying on another lock slot until you succeed.
Figure 4-9 Inserting the Key for Unlocking
2) If the AP is installed on the wall, hold the AP with both of your hands and push it upward to separate it from the
bracket.
Figure 4-10 Removing the Wall-Mount AP

3) If the AP is installed on the ceiling, hold the AP with both of your hands and push it in different directions as shown in
figure 4-11 until the AP is separated from the bracket (the AP can be removed only in one direction).
Figure 4-11 Removing the Ceiling-Mount AP

5 Quick Configuration
Step 1: Navigate to the Web login page.
In the Fit mode, the IP address of the LAN1 port and the LAN2 port are 192.168.110.1/24.
In the Fat mode, the IP address of the LAN1 port is 192.168.110.1/24, and the IP address of the LAN2 port is
192.168.111.1/24.
Step 2: Log into the AP device.
Enter the username and password, click Login.
The default username is admin, and the default password is admin.
Step 3: Perform quick configuration.
By default, the AP works in the Fit mode.
The Dashboard displays the current mode and allows you to switch the mode.

Click FAT AP Mode on the right panel to switch the AP over to the FAT mode.
Click the button to perform quick configuration.
The AP can work in AP access mode or wireless routing mode.
1 ) Select AP Access Mode.
Configure the VLAN and IP address, and click Next.

Enter the SSID and WiFi password, and click Finish to finish the configuration.

2 ) Select Wireless Routing Mode.
Select an Internet connection type, enter related parameters, and click Next.

Enter the SSID and WiFi password, and click Finish to finish the configuration.