Tennant Speed Scrub ES KIT 2701 User manual

KIT NO. 605555
2701/3301 Speed Scrub EStKIT
Page 1 of 4
Speed Scrub
605556 Rev. 00 (08–98) Tennant Company Printed in U.S.A
630136 Pump, 24V 1
630385 Fitting, Nipple 3/4” 1
630145 Timer, 24V 1
210044 Valve, Check 1
630419 Switch, Rocker 1
578720 Splashguard, Switch 1
130738 Light, Indicator 1
578008000 Screw, M5X.8x30 1
601490 Fitting, Bulkhead 1
140283 Nut, 10–24 Nylock 1
150415 Fitting, Elbow 1/4mX3/8H 1
25160 Tubing 5/8ODx3/8ID .5 ft
25160 Tubing 5/8ODx3/8ID 1.25 ft
140310 Clamp, Hose 4
630138 Filter, Screen 1
603166 Switch, Float 1
605551 Harness, ES Wire 1
604858 Asm., Wire #90 Red 1
604859 Asm., Wire #84, #86 PInk 1
605552 Asm., Wire #51, #53, #55 Black 1
130041 Wire Tie 4
630440 Decal, Filter Remove 1
INSTALLATION INSTRUCTIONS:
(Installation Time: 1 hour)
TOOLS REQUIRED: Standard & Philips Screwdriver,
Electric Drill w/ 1/8”, 1/4”, 7/16”, 1/2”, 11/16” & 1-3/8” Drill Bits
& 1/4” NPT Tap.
FOR SAFETY: Before installing kit, dis-
connect positive (+) battery cable from
batteries.
STEP 1: Drill holes as indicated.
KITS CONTENTS
Hole Sizes:
A= 1-3/8” hole
B= 11/16” hole
C= 7/16” hole
NOTE: After drilling
hole (C), thread hole
with a 1/4” NPT tap.
4.0”
A
Tank Lip
VACUUM
MOTOR
B
1.25”
4.75”
C
4.25”
9.25”
Drill Pilot Hole
Home

Page 2 of 4
KIT NO. 605555
ES KIT
605556 Rev. 00 (08–98) Tennant Company Printed in U.S.A
STEP 2: Install ES Components as Shown.
IMPORTANT:
Float switch must
be positioned as
shown when tank
is closed.
Float
Switch
Bulkhead
Clear
Washer
Bulkhead
Rubber
Seal
Bulkhead
Bulkhead
Nut
Hex Nipple
Screen
Filter
Float
Switch
Nut
ES Pump
Tubing .5 ft
Check Valve
Hose Clamp
Tubing 1.25 ft
Elbow
Fitting Hose
Clamp
NOTE: Point arrow on check
valve in the direction as shown.
NOTE: Use pipe sealing tape
for all threaded connections.
Place decal on clear
Recovery Tank Lid.
Home

Page 3 of 4
KIT NO. 605555
ES KIT
605556 Rev. 00 (08–98) Tennant Company Printed in U.S.A
STEP 3: Drill holes as indicated.
A= .125”hole
B= .5”hole
STEP 4: Install ES components as shown.
NOTE: If your rear cover
panel does not have
knock outs for the ES
components, you must
order ES rear panel cover
#606276.
ES Switch ES Switch
Splashguard
ES Light
Timer
Screw
Nut
NOTE: Posi-
tion ES Switch
with the brass
terminal up.
A
B
2.5”
7.0”
Existing Main
Wire Harness
Hole
5.0”
Rear Cover
Panel
Home

Page 4 of 4
KIT NO. 605555
ES KIT
605556 Rev. 00 (08–98) Tennant Company Printed in U.S.A
STEP 5: Connect ES Wiring as Shown.
BACKSIDE VIEW OF
REAR PANEL COVER
ES PUMP
FLOAT SWITCH
TIMER
ES SWITCH
ES LIGHT
ES WIRE HARNESS NOTE: Route ES wire harness up to
control console. Follow along ma-
chine’s main wire harness. Secure ES
wire harness with wire ties provided.
NOTE: Route
ES wire harness
up through
drilled hole in
control console.
RED
GREEN
BLK
BLK
WHITE
BLACK
NOTE: Secure ES wire harness
to ES pump with wire tie.
CONTROL CONSOLE
T6
T3
T1
GRN
51 BLK
90 RED
GRN
Brass Terminal
Copper Terminals
NOTE: Secure white wire
to ES pump with wire tie.
MAIN POWER SWITCH
53 BLK
55 BLK 90 RED
RED
BLACK
55 BLK
86 PINK
84 PINK
GREEN
WHITE
BLKRED
RED
Main Wire
Harness hole
in control
housing
WHITE
Home