Tennant T15 Operating and installation instructions

T15
*331555*
www.tennantco.com
331555
Rev. 00 (05-2007)
North America / International
The Safe Scrubbing AlternativeR
Service Information Manual

FOR REPLACEMENT PARTS
Identify machine model and serial number.
1. (A) Identify the machine model.
2. (B) Identify the machine serial number from the data plate.
Refer to the TENNANT Parts Manual.
NOTE: Only use TENNANT Company supplied or equivalent parts. Parts and supplies may be ordered
online, by phone, by fax or by mail.
Tennant Company
PO Box 1452
Minneapolis, MN 55440
Phone: [phone] or (763) 513--2850
www.tennantco.com
Specifications and parts are subject to change without notice.
Copyright E2007TENNANT Company, Printed in U.S.A.
AB
ii T15 331555 (05-2007)

T15 Service Information Manual
Table of Contents
(Page 1 of 3)
T15 331555 (05-2007) iii
page
SAFETY PRECAUTION
S
………………………………...………………………….………………………………
…
vi
GENERAL MACHINE INFORMATIO
N
Component Locator………………………………...………………………….……………………………
…
2 to 11
Touch Panel Detail………………………………...………………………….……………………
…
3
Switches & Circuit Breakers………………………………...………………………….…………
…
4
Specifications………………………………...………………………….…………………………………… 12 to 14
Dimensions & Capacities………………………………...………………………….……………… 12
Performance………………………………...………………………….……………………………
…
12
Power Type………………………………...………………………….……………………………
…
13
Tires………………………………..………………...………………………….……………………
…
13
FaST System………………………………...………………………….……………………………
…
13
Dimensional Drawings………………………………...………………………….…………………
…
14
Basic Troubleshooting………………………………...………………………….…………………………
…
15 to 16
MAINTENANCE & REPAI
R
Maintenance Checkpoints………………………………...………………………….……………………
…
18
Maintenance Chart………………………………...………………………….……………………………
…
19
Lubrication………………………………………………..…...………………………….…………………
…
20
Steering Caster Pivot Bearing………………………………...………………………….………… 20
Rear Squeegee Casters………………………………...………………………….………………
…
20
Steering Gear Chain………………………………...………………………….…………………… 20
Batteries………………………………...…………………...…………………….…………………………
…
21 to 26
Charging Batteries………………………………...………………………….……………………… 22
To Replace Batteries………………………………...………………………….…………………
…
25
Control Panel………………………………...………………………….…………………………………… 27 to 28
To Access Control Panel………………………………...………………………….………………
…
27
Instrument Panel………………………………...………………………….………………………………
…
29 to 36
To Replace Touch Panel………………………………...………………………….………………
…
29
To Replace Circuit Board………………………………...………………………….……………… 34
Circuit Breakers………………………………...………………………….………………………………… 37 to 42
Resetable Circuit Breakers………………………………...………………………….……………
…
37
To Replace Circuit Breaker………………………………...………………………….……………
…
38
Fuses………………………………...………………………….……………………………………. 41
To Replace Fuse………………………………...………………………….………………………
…
41
Directional Control Pedal………………………………...………………………….……………………… 43 to 46
To Replace Propel Motor Controller………………………………...………………………….…
…
44
To Replace Taillight Bulb………………………………...………………………….……………………… 46
Scrub Head………………………………………………...…...………………………….………………… 47 to 65
Scrub Head Links………………………………...………………………….………………………
…
47
To Replace Scrub Head Links………………………………...………………………….… 48
To Remove Disc Scrub Head………………………………...………………………….…………
…
49
To Install Disc Scrub Head………………………………...………………………….……………
…
51
To Replace Disc Scrub Head Brush Motor………………………………...……………………
…
53
To Remove Cylindrical Scrub Head………………………………...………………………….…
…
57
To Install Cylindrical Scrub Head………………………………...………………………….……
…
59
To Replace Cylindrical Scrub Head Brush Motor………………………………...………………
…
61
Cylindrical Brush Drive Belt………………………………...………………………….…………………… 66 to 69
To Replace Brush Drive Belt………………………………...………………………….…………
…
66
Disc Scrub Head Skirts………………………………...………………………….………………………
…
70 to 71
Scrub Head Floor Skirts………………………………...………………………….………………
…
70
To Adjust Disc Scrub Head Skirts………………………………...………………………
…
70
To Replace Disc Scrub Head Skirts………………………………...……………………
…
71
Cylindrical Brush Head Debris Tray………………………………...………………………….…………
…
72 to 75
To Remove Debris Tray………………………………...………………………….………………
…
72
To Install Debris Tray………………………………...………………………….…………………
…
74
To Replace Debris Tray Skirt………………………………...………………………….…………
…
75
Scrub Brushes………………………………...………………………….…………………………………
…
76 to 82
Disc Scrub Brushes………………………………...………………………….……………………
…
76
To Replace Disc Scrub Brushes………………………………...…………………………. 76
Cylindrical Scrub Brushes………………………………...………………………….……………
…
78
To Replace Cylindrical Scrub Brushes………………………………...…………………
…
78
To Check and Adjust Cylindrical Brush Pattern………………………………...………… 80
Scrub Head Lift Actuator………………………………...………………………….………………………
…
83 to 87
To Replace Scrub Head Lift Actuator………………………………...………………………….… 84

T15 Service Information Manual
Table of Contents
(Page 2 of 3)
iv T15 331555 (05-2007)
MAINTENANCE & REPAIR (continued) page
Solution System………………………………...………………………….………………………………
…
88 to 104
Recovery Tank………………………………...………………………….…………………………
…
88
To Remove Recovery Tank………………………………...………………………….…… 89
To Install Recovery Tank………………………………...………………………….………
…
93
Solution Tank………………………………...………………………….…………………………… 96
To Remove Solution Tank………………………………...………………………….……
…
97
To Install Solution Tank………………………………...………………………….………
…
101
Manual Solution Valve………………………………...………………………….…………………………
…
105 to 107
To Replace Solution Valve………………………………...………………………….……………
…
105
Solution Solenoid Valve………………………………...………………………….………………………
…
108 to 110
To Replace Solution Solenoid Valve………………………………...………………………….…
…
108
FaST System………………………………...………………………….…………………………………… 111
FaST Supply Hose Connector………………………………...………………………….………… 111
FaST Solution Filter Screen………………………………...………………………….…………… 111
ES Pump……………………………………………….……...………………………….…………………
…
112 to 114
To Replace ES Pump………………………………...………………………….…………………
…
112
Squeegees………………………………………………………..………………………….………………
…
115 to 122
To Remove Rear Squeegee Assembly………………………………...………………………….
…
115
To Install Rear Squeegee Assembly………………………………...………………………….…
…
117
To Level Rear Squeegee………………………………...………………………….……………… 118
To Adjust Rear Squeegee Blade Deflection………………………………...……………………
…
120
Rear Squeegee Casters………………………………...………………………….………………
…
122
To Adjust Rear Squeegee Guide Roller………………………………...…………………………
.
122
Rear Squeegee Blades………………………………...………………………….………………………
…
123 to 133
To Replace or Rotate Rear Squeegee (Rear) Blade………………………………...…………
…
123
To Replace or Rotate Rear Squeegee (Front) Blade………………………………...…………
…
125
Rear Squeegee Wheel Cams………………………………...………………………….…………
…
128
Rear Squeegee Leveling Knob………………………………...………………………….………
…
128
To Replace Rear Squeegee Lift Cable………………………………...………………………….
…
129
Side Squeegee Blades………………………………...………………………….………………… 132
To Replace Side Squeegee Blades………………………………...……………………… 133
Squeegee Lift Actuator………………………………...………………………….………………………… 134 to 137
To Replace Rear Squeegee Lift Actuator………………………………...………………………
…
135
Vacuum Fan………………………………...………………………….……………………………………. 138 to 143
To Remove Vacuum Fan Assembly………………………………...………………………….…
…
138
To Install Vacuum Fan Assembly………………………………...………………………….……
…
140
To Replace Vacuum Fan………………………………...………………………….………………
…
142
Pre-Sweep Brushes………………………………...………………………….……………………………
…
144 to 149
Pre-Sweep Disk Brushes………………………………...………………………….……………… 144
Replacing the Disk Brushes………………………………...………………………….…… 144
Pre-Sweep Cylindrical Brush………………………………...………………………….…………
…
146
Checking and Adjusting Cylindrical Brush Pattern………………………………...……
…
146
Replacing the Pre-Sweep Cylindrical Brush………………………………...……………
…
148
Pre-Sweep Skirts and Seals………………………………...………………………….…………………
…
150
Pre-Sweep Side Skirts………………………………...………………………….…………………
…
150
Pre-Sweep Recirculation Skirt………………………………...………………………….………… 150
Pre-Sweep Rear Skirt………………………………...………………………….…………………
…
150
Pre-Sweep Brush Drive Belt………………………………...………………………….…………………
…
151
Static Drag Strap………………………………...………………………….………………………………
…
152
Tires……………………………………..……………...………………………….…………………………
…
152 to 178
Rear Tires and Wheels………………………………...………………………….………………… 153
To Remove Rear Tire………………………………...………………………….…………
…
153
To Install Rear Tire………………………………...………………………….……………
…
154
To Replace Rear Wheel Bearings………………………………...………………………
…
155
Front Tire and Wheel………………………………...………………………….…………………
…
157
Front Wheel Support Caster Bearing Assembly………………………………...………
…
157
To Remove Front Drive Assembly………………………………...………………………
…
157
To Install Front Drive Assembly………………………………...………………………….
…
159
Propel Motor Service………………………………...………………………….…………… 160
General information………………………………...………………………….……
…
160
Terminal Connections………………………………...………………………….…
…
161
Electric Brake Disassembly………………………………...………………………
…
162
Brake Disk Replacement………………………………...………………………….
…
166
Tire Replacement………………………………...………………………….………
…
167
Commutator Brush Replacement………………………………...………………… 171
To Replace Drive Assembly Caster Bearing and Thrust Washers……………………
…
174
To Replace Drive Assembly Pivot Cone Bearing………………………………...………
…
177

T15 331555 (05-2007) v
T15 Service Information Manual
Table of Contents
(Page 3 of 3)
MAINTENANCE & REPAIR (continued) page
Steering……………………………………………………………….…...………………………….……… 179 to 189
To Adjust Steering Chain………………………………...………………………….……………… 179
To Replace Steering Chain………………………………...………………………….……………
…
180
To Replace Large Steering Sprocket………………………………...………………………….… 181
To Replace Small Steering Sprocket………………………………...………………………….… 182
To Replace Steering Housing Bearings………………………………...…………………………
.
184
To Replace Steering U-joint………………………………...………………………….…………… 188
Seat………………………………………………………...………………………….……………………… 190 to 193
Operator Seat………………………………...………………………….…………………………… 190
To Remove Seat Assembly………………………………...………………………….……
…
190
To Install Seat Assembly………………………………...………………………….………
…
192
To Adjust Seat Position………………………………...………………………….………
…
193
Pushing,Towing,and Transporting the Machine………………………………...………………………
…
194 to 196
Pushing or Towing the Machine………………………………...………………………….………
…
194
Transporting the Machine………………………………...………………………….……………
…
194
Machine Jacking………………………………...………………………….………………………………
…
196
Storage Information………………………………...………………………….……………………………
…
197
Freeze Protection………………………………...………………………….………………………
…
197
ELECTRICA
L
Electrical Schematics………………………………...………………………….…………………………
…
200 to 202
Harness Drawings………………………………...………………………….……………………………… 203 to 210
Electrical Symbols & Terms………………………………...………………………….…………………
…
211
Key Switch………………………………...………………………………………...……………….………
…
212
Key OFF Power Distribution………………………………...………………………….…………………
…
213
Key START Power Distribution………………………………...………………………….………………
…
214
Key ON Power Distribution………………………………...………………………….……………………
…
215
Power Up Troubleshooting………………………………...………………………….……………………
…
216
Touch Panel Wiring………………………………...………………………….……………………………
…
217
Touch Panel Troubleshooting………………………………...………………………….………………… 218
Scrub Brushes ON………………………………...………………………….……………………………
…
219
Vacuum Fan(s) ON & Squeegee DOWN………………………………...………………………….……
…
220
Vacuum Fan(s) OFF & Squeegee UP………………………………...………………………….………
…
221
Vacuum Fan Troubleshooting………………………………...………………………….………………… 222
Squeegee Troubleshooting………………………………...………………………….…………………… 224
Scrub Head DOWN & Conventional Solution Valve ON………………………………...………………
…
226
Scrub Head UP………………………………...………………………….…………………………………
…
227
Forward Propel………………………………...………………………….…………………………………
…
228
Reverse Propel………………………………...………………………….…………………………………
…
229
Neutral (No Propel) with Brake Pedal Depressed………………………………...……………………
…
230
Propel Controller………………………………...………………………….………………………………
…
231 to 233
Diagnostics and Troubleshooting………………………………...………………………….……
…
231
Operating Lights………………………………...………………………….………………………………
…
234
Horn ON……………………………………………………...……...………………………….……………
…
234
Extended Scrub (ES) System ON………………………………...………………………….……………
…
235
Power Wand ON………………………………...………………………….………………………………
…
235
ES System Troubleshooting………………………………...………………………….…………………
…
236 to 237
ES Filter Flush Troubleshooting………………………………...………………………….……………… 238
Pre-Sweep System ON………………………………...………………………….………………………
…
239
Pre-Sweep Dust Control ON………………………………...………………………….…………………
…
240
FaST System ON………………………………...………………………….………………………………
…
241
Battery Charger Troubleshooting………………………………...………………………….……………
…
242 to 246
Machine Control Board Connectors………………………………...………………………….…………
…
247
Propel Controller Connectors………………………………...………………………….…………………
…
248
Operating & Configuration Modes………………………………...………………………….……………
…
249 to 260
Normal Mode………………………………...………………………….……………………………
…
250
Self-Test Mode………………………………...………………………….…………………………
…
252
Error Codes………………………………...………………………….……………………
…
253
Troubleshooting………………………………...………………………….………………… 254
Manual Mode………………………………...………………………….……………………………
…
256
Enable/Disable Chart………………………………...………………………….…………
…
257
Input Display Mode………………………………...………………………….……………………
…
258
Restricted Down Pressure Mode………………………………...………………………….……
…
259
Software Revision Date Display Mode………………………………...………………………….
…
260

vi T15 331555 (05-2007)
SAFETY PRECAUTIONS
The following symbols are used throughout this
manual as indicated in their description:
WARNING: To warn of hazards or
unsafe practices that could result in
severe personal injury or death.
FOR SAFETY: To identify actions that
must be followed for safe operation of
equipment.
This machine is designed solely for scrubbing dirt
and dust in an indoor environment. Tennant does
not recommend using this machine in any other
environment.
The following information signals potentially
dangerous conditions to the operator or
equipment. Read this manual carefully. Know
when these conditions can exist. Locate all safety
devices on the machine. Then, take necessary
steps to train machine operating personnel.
Report machine damage or faulty operation
immediately. Do not use the machine if it is not in
proper operating condition.
WARNING: Batteries emit hydrogen gas.
Explosion or fire can result. Keep
sparks and open flame away. Keep
covers open when charging.
WARNING: Flammable materials can
cause an explosion or fire. Do not use
flammable materials in tank(s).
WARNING: Flammable materials or
reactive metals can cause an explosion
or fire. Do not pickup.
FOR SAFETY:
1. Do not operate machine:
-- Unless trained and authorized.
-- Unless operation manual is read and
understood.
-- With brake disabled.
-- In flammable or explosive areas unless
designed for use in those areas.
2. Before starting machine:
-- Make sure all safety devices are in
place and operate properly.
-- Check brakes and steering for proper
operation (if so equipped).
3. When using machine:
-- Go slow on inclines and slippery
surfaces.
-- Use care when backing machine.
-- Follow mixing and handling
instructions on chemical containers.
4. Before leaving or servicing machine:
-- Stop on level surface.
-- Turn off machine and remove key.
5. When servicing machine:
-- Avoid moving parts. Do not wear loose
jackets, shirts, or sleeves when
working on machine.
-- Block machine tires before jacking
machine up.
-- Jack machine up at designated
locations only. Block machine up with
jack stands.
-- Use hoist or jack that will support the
weight of the machine.
-- Wear eye and ear protection when
using pressurized air or water.
-- Disconnect battery connections before
working on machine.
-- Avoid contact with battery acid.
-- Use Tennant supplied or equivalent
replacement parts.
6. When loading/unloading machine
onto/off truck or trailer.
-- Turn off machine.
-- Use truck or trailer that will support
the weight of the machine.
-- Use winch. Do not push the machine
onto/off the truck or trailer unless the
load height is 380 mm (15 in) or less
from the ground.
-- Block machine tires.
-- Tie machine down to truck or trailer.
T15 Safety Precautions

T15
GENERAL
MACHINE
INFORMATION
1
G
T15 331555 (05-2007)

T15 Component Locator
(page 1 of 10)
F
R
O
N
T
FRONT
IGNITION SWITCH S1
EMERGENCY
STOP SWITCH S2
HOUR METER
TOUCH PANEL
BRAKE PEDAL &
BRAKE SWITCH SW2 THROTTLE PEDAL &
THROTTLE SENSOR
SWITCH & CIRCUIT
BREAKER PANEL
PRE-SWEEP
SWITCHES S10 & S11
F
R
ON
T
G
2 T15 331555 (05-2007)

Touch Panel Detail
A. Battery discharge indicator
B. Recovery tank full indicator
C. FaST/ES enabled indicator
D. FaST/ES ON/OFF button
E. Squeegee/Vacuum Fan indicator
F. Squeegee/Vacuum Fan ON/OFF button
G. Scrub Head Pressure indicator
H. Scrub System ON/OFF button
AB
C
D
E
F
G
H
T15 Component Locator
(page 2 of 10)
G
T15 331555 (05-2007) 3

Switches & Circuit Breakers
A D
BCF
L K JGHI
M N
A. CB7 – 20 Amp Circuit Breaker – Single Vacuum Fan (or)
40 Amp Circuit Breaker – Dual Vacuum Fans (option)
B. S7 – Horn Button
C. S8 – Operating Lights Switch
D. S6 – Power Wand Switch (option)
E. CB1 – 10 Amp Circuit Breaker – Machine Power
F. CB2 – 10 Amp Circuit Breaker – Battery Discharge Indicator
G. CB6 – 15 Amp Circuit Breaker – Machine Control Board & Touch Panel
H. CB5 – 10 Amp Circuit Breaker – Horn
I. CB4 – 10 Amp Circuit Breaker – Scrub Head Actuator, Back Up
Alarm (option) and Power Wand (option)
J. CB3 – 15 Amp Circuit Breaker – Operating Lights
K. CB9 – 30 Amp Circuit Breaker – Left Disk Scrub Brush Motor (or)
Rear Cylindrical Scrub Brush Motor
L. CB8 – 30 Amp Circuit Breaker – Right Disk Scrub Brush Motor (or)
Front Cylindrical Scrub Brush Motor
M. S11 – Pre-Sweep Dust Control Switch (option)
N. S10 – Pre-Sweep System ON/OFF Switch (option)
E
T15 Component Locator
(page 3 of 10)
G
4 T15 331555 (05-2007)

P
O
Q
Switches & Circuit Breakers
T15 Component Locator
(page 4 of 10)
O. CB11 – 10 Amp Circuit Breaker – FaST System
P. CB10 – 25 Amp Circuit Breaker – Pre-Sweep System (option)
Q. CB12 – 10 Amp Circuit Breaker – Pre-Sweep Side Brush(es) (option)
G
T15 331555 (05-2007) 5

FRONT
T15 Component Locator
(page 5 of 10)
F
R
O
NT
MACHINE
CONTROL BOARD
FRONT CHANNEL
(INSIDE VIEW)
ELECTRICAL PANEL
(INSIDE VIEW)
PROPEL
CONTROLLER
HORN SWITCH S7
PROPEL
CONTROLLER
OPERATING LIGHTS
SWITCH S8
POWER WAND
SWITCH S6
CIRCUIT
BREAKERS
CB1, CB2,
CB3, CB4,
CB5, CB6,
CIRCUIT
BREAKERS
CB7, CB8,
CB9
MAIN CONTACTOR M1
CIRCUIT
BREAKER CB10
FUSE FU1
VACUUM FAN
CONTACTOR M2
BRUSH
CONTACTOR M3
CIRCUIT
BREAKER CB11
G
6 T15 331555 (05-2007)

T15 Component Locator
(page 6 of 10)
BATTERIES
SEAT SWITCH S3
SCRUB HEAD
ACTUATOR
FaST WATER
PUMP
FaST WATER
PRESSURE SWITCH
FaST SOLENOID
VALVE
FaST DETERGENT
PUMP
FaST AIR PUMP
PROPEL MOTOR
ELECTRIC BRAKE
SOLENOID
FRONT
F
R
O
N
T
VIEWED UNDER MACHINE
(BEHIND SCRUB HEAD)
F
R
O
N
T
G
T15 331555 (05-2007) 7

RIGHT SCRUB
BRUSH MOTOR
FR
O
N
T
BRUSH MOTORS
SHUNT (MIDDLE REAR
OF SCRUB HEAD)
T15 Component Locator
(page 7 of 10)
CYLINDRICAL
SCRUB HEAD
DISK SCRUB
HEAD
FRONT SCRUB
BRUSH MOTOR
REAR SCRUB
BRUSH MOTOR
BRUSH MOTORS
SHUNT
LEFT SCRUB
BRUSH MOTOR
FRON
T
F
RO
NT
VACUUM FAN
MOTOR(S)
G
8 T15 331555 (05-2007)

RECOVERY TANK FULL
FLOAT SWITCH S4
FR
ONT
RECOVERY TANK HALF
FULL FLOAT SWITCH S5
SOLUTION TANK FULL
FLOAT SWITCH S9
T15 Component Locator
(page 8 of 10)
ES PUMP
FR
O
N
T
F
R
O
N
T
G
T15 331555 (05-2007) 9

CONVENTIONAL
SOLUTION VALVE
T15 Component Locator
(page 9 of 10)
SQUEEGEE
ACTUATOR
POWER
WAND PUMP
FRONT
F
R
O
NT
F
R
O
N
T
G
10 T15 331555 (05-2007)

T15 Component Locator
(page 10 of 10)
PRE-SWEEP
COMPONENTS
HORN (BEHIND
HEADLIGHT)
F
R
O
N
T
F
R
O
N
T
FLASHING
LIGHT
BACK-UP ALARM
FR
O
N
T
G
T15 331555 (05-2007) 11

GENERAL MACHINE DIMENSIONS/CAPACITIES
Item Dimension/capacity
Length 1830 mm (72 in)
Length (with Pre--Sweep) 2465 mm (97 in)
Width (less squeegee) 1025 mm (40.25 in)
Width (with squeegee) 1155 mm (45.5 in)
Height 1360 mm (53.5 in)
Height with overhead guard 2030 mm (80 in)
Disk brush diameter for side brush (option) 460 mm (18 in)
Disk brush diameter for Pre--Sweep (option) 380 mm (15 in)
Disk brush diameter for 700 mm (28 in) scrub head 355 mm (14 in)
Disk brush diameter for 900 mm (36 in) scrub head 460 mm (18 in)
Cylindrical sweep brush diameter for Pre--Sweep (option) 155 mm (6 in)
Cylindrical sweep brush length for Pre--Sweep (option) 810 mm (32 in)
Cylindrical scrub brush diameter 155 mm (6 in)
Cylindrical brush length for 700 mm (28 in) scrub head 700 mm (28 in)
Cylindrical brush length for 900 mm (36 in) scrub head 900 mm (36 in)
Squeegee width for 700 mm (28 in) scrub head 950 mm (37.5 in)
Squeegee width for 900 mm (36 in) scrub head 1155 mm (45.5 in)
Scrubbing path width for 700 mm (28 in) scrub head 710 mm (28 in)
Scrubbing path width for 900 mm (36 in) scrub head 915 mm (36 in)
Solution tank capacity 170 L (45 gallons)
Recovery tank capacity 210 L (55 gallons)
GVWR 1134 Kg (2500 lbs)
GENERAL MACHINE PERFORMANCE
Item Measure
Aisle turnaround width 2080 mm (82 in)
Aisle turnaround width (with Pre--Sweep) 2770 mm (109 in)
Travel Speed 9.6 Km (6 mph)
Maximum rated climb and descent angle for transport 8_@ gross weight
Maximum rated climb and descent angle for scrubbing 4_
Maximum rated climb and descent angle for trailering 11_
T15 Specifications
(page 1 of 3)
G
12 T15 331555 (05-2007)

POWER TYPE
Type Quantity Volts Ah Rating Weight
Batteries 6 6 235 @ 20 hr rate 30 kg (67 lb)
6 6 335 @ 20 hr rate 47 kg (104 lb)
Type Use VDC kW (hp)
Electric Motors Pre--Sweep brush (disk) 36 0.20 (0.25)
Pre--Sweep brush (cyl) 36 0.45 (0.60)
Scrub brush (disk) 36 055 (075)Scrub brush (disk) 36 0.55 (0.75)
Scrub brush (cylindrical) 36 0.55 (0.75)
Vacuum fan 36 06(08)Vacuum fan 36 0.6 (0.8)
Propelling 36 11(15)Propelling 36 1.1 (1.5)
Type VDC amp Hz Phase VAC
Chargers (Smart) 36 21 45--65 185--265
TIRES
Location Type Size
Front (1) Solid 100 mm wide x 305 mm OD (4 in wide x 12 in OD)
Rear (2) Solid 90 mm wide x 305 mm OD (3.5 in wide x 12 in OD)
FaST SYSTEM
Item Measure
Solution pump 36 Volt DC, 5A, 5.7 LPM (1.5 GPM) open flow,
45 psi bypass setting
Solution flow rate 1.1LPM(0.30GPM)
Detergent to water dilution ratio 1:1000
Detergent flow rate 1.14 CC/Minute (0.038 Ounces/Minute)
T15 Specifications
(page 2 of 3)
G
T15 331555 (05-2007) 13

TOP VIEW
SIDE VIEW
2030 mm
(80.0 in)
1360 mm
(53.5 in)
+
--
921 mm
(36.25 in)
1155 mm
(45.5 in)
1092 mm
(43.0 in)
1830 mm
(72.0 in)
1025 mm
(40.25 in)
1025 mm
(40.35 in)
405 mm
(16.0 in)
810 mm
(32.0 in)
FRONT VIEW
915 mm
(36.0 in)
350790
MACHINE DIMENSIONS
T15 Specifications
(page 3 of 3)
G
14 T15 331555 (05-2007)