TensCare mamatens my time User manual

TensCare Ltd, 9 Blenheim Road,
Longmead Business Park,
Epsom, Surrey KT19 9BE, UK
Tel [phone]
Email: [email protected]
www.mama-tens.info
EC Declaration of Conformity
TensCare Ltd hereby declare that an examination of the production quality
assurance system has been carried out following the requirements of the
UK national legislation according to Annex V of the Directive 93/42/EEC on
medical devices. We certify that the production quality system conforms
with the relevant provisions of the aforementioned legislation, and the result
entitles the organisation to use the CE 0473 marking on this product.
Instructions for Use
PLEASE READ THIS BEFORE YOU GO INTO LABOUR
“TIMED, CONTROLLED
PURE POWERFUL
PAIN RELIEF”
Distributed by:
0473
Pub Ref: I –MT-UK Rev2 6/14
0473

Section Page
1 Introduction and Features 1
2 How “TENS” works 4
3 The Programmes 6
4 Contraindications 8
5 Cautions and Warnings 9
6 Controls 11
7 Screen Display 15
8 Contents 17
9 Installation of Batteries 18
10 Connecting Mono Leadwire 19
11 Positioning of Pads 19
12 When your labour starts 21
13 Extra pain relief 23
14 General Information 24
15 Guarantee 29
16 Troubleshooting 30
17 Consumables and servicing 31
18 WEEE 32
19 Technical Specifications 33
20 EMC Precautions 35
ContentsQuickstart Guide
Read instruction book carefully
Attach lead to the unit
Put everything back into the
box until labour begins
After the birth, dispose of
electrodes and leads
Check contents
Attach the electrodes to your
back and try out the unit to
see how it feels
As soon as labour begins, set
up, attach and use the unit as
per instructions
Place unit and neck cord back
into the box
PressON button to check that
the unit is working (LCD will
be activated) then switch OFF
Replace electrodes onto their
liners and seal them in the
re-sealable bag
Adjust strength using the
up and down buttons
MamaTENS Help LINE
Helpline
01372 723434
ON OFF
UP DOWN
1
4
7
10
2
5
8
11
3
6
9

2
1
1. INTRODUCTION
The MamaTENS “My Time” is a very
special maternity TENS as it not only offers
powerful controllable pain relief, but also
gives information about contraction times
and the length of your labour. (See Labour
Log). The MamaTENS “MyTime” was
developed as a result of twenty years of
manufacturing and with feedback from
tens of thousands of mothers who have
used TENS in labour. The aim was to
produce the ULTIMATE maternity TENS;
the MamaTENS “MyTime” is the result.
MamaTENS “My Time” Special features:
• MamaTENS “My Time” LABOUR LOG
Labour Log enables you to monitor the duration and frequency of your
contractions by measuring each one in seconds and showing the time
between them. Labour Log can show the total time since you started to
use your MamaTENS “MyTime”. Labour Log is unique to the MamaTENS
“My Time” and provides invaluable help to you and your midwife.
• MamaTENS “My Time” PAD ALARM
Perfect pad contact and condition is important to obtain maximum benefit
from any TENS unit. To ensure the best performance, the MamaTENS “My
Time” has been fitted with a “Pad Alarm” that shows you if the contact
of any of the four pads to your body is lost or below standard. You might
otherwise not be aware of the break in contact, which would interrupt
the benefit being obtained from the unit.
• MamaTENS “My Time” COMFORT STRENGTH CONTROL
Gives a gentle and reproducible stimulation. “CSC” monitors skin and
pad resistance and adjusts the output to maintain a constant feeling.
This gives you greater comfort and takes away the possibility of getting
an unpleasant spike in strength if a pad starts coming away from the
body. With “CSC” you can increase the strength on the MamaTENS
“My Time” in very small steps which is much more comfortable than
conventional TENS units.

4
3
MamaTENS “My Time” other features:
• Preset programmes and intelligent “Active Power” ramp
The MamaTENS “My Time” has 2 preset programmes. These programmes
have been clinically proven to give relief from labour pain. Both
programmes have a boost facility so that they can be used between
and during contractions. A power ramp facility, a variation of “intense
TENS”, has also been included to help counter extreme pain. In Active
Power ramp mode, as long as you keep your finger pressed, the strength
keeps increasing beyond normal settings to action the third pain relief
mechanism of TENS called “Brief Intense TENS”, to help counter extreme
pain. You can use the intelligent Active Power control to hold the
strength just below the highest you can stand.
• Easy Start - One Touch Memory
The MamaTENS “My Time” has intelligent memory that enables the unit
to remember the last programme and the strength setting used. The
strength level goes back to 75% of the last level used.
• 2-in-1 Lead Connection
Unique single plug connection for both channels which simplifies lead
connection and management during use.
• Backlit LCD screen
Makes the screen easy to read.
• Sculptured keypad
Makes it easy to select the right button.
2. HOW “TENS” WORKS
TENS stands for Transcutaneous Electrical Nerve Stimulation.
TENS stimulates your body’s own natural defences against pain.
TENS has been used by thousands of expectant mothers and is
commonly used as part of the birth plan.
You can use it from the start of the first contraction at home and
take it into hospital with you. Some women find that TENS is the
only pain relief they need during their labour.
THE ADVANTAGES OF TENS
• Allows mother to control her pain relief
• Allows mother to be mobile during labour
• Can be used at home and taken into hospital

6
5
TENS sends a very small electric current through the skin
which works in THREE ways:
Pain Gate
Stimulating the sensory nerves, which carry touch and temperature signals.
These nerves go to the same connections in the spine as the nerves carrying
pain. A strong sensory signal will block the pain signal travelling up the spine to
the brain. This is known as the “Pain Gate”.
Endorphin Release
At low frequency settings, and slightly stronger output, TENS drives the motor
nerves to produce a small repetitive muscle contraction. This is seen by the
brain as exercise and this promotes release of Endorphins – your body’s own
natural pain killer. The relief builds up and normally takes about 40 minutes
to reach a maximum level which can last for hours.
Brief Intense
A very strong TENS signal produces an additional pain blocking effect for a
short period of time.
3. THE PROGRAMMES
The i-touch MamaTENS has 2 preset and a Power Ramp programme.
Each of the two preset programmes is in two forms
First preset programme is shown on the screen as “A Int” and “A Con”.
Second preset programme is shown on the screen as “B Int” and “B Con”.
Programme A is for early labour with mild contractions.
(This can last a long time)
A Int: This is the first programme to be used from the onset of labour. It is
for the period between contractions and is shown on the display as “Int” for
“interval”. It gives a pulsing sensation.
When a contraction starts press the BOOST button to change to A Con.
This is the programme to be used during contractions and gives a continuous
tingling feeling.
At the end of a contraction, press the BOOST button again to return to A Int.

8
7
Some mothers can go right through their whole labour using only the “A”
programmes. Other mothers will want to change to the “B” programmes as
the pain increases to moderate. Do this by pressing the “P” (Programme)
button once.
As before, B Int should be used in the interval between contractions.
Press the BOOST button to change to B Con when a contraction starts.
You may notice that the strength in the upper pads is slightly greater
than in the lower pads -this is intentional and part of the therapy.
If your labour pains become extremely severe or if you do not start using
the unit until late into your labour, thereby not allowing time for the
endorphin release to take effect, then use the “Power Ramp” programme.
Power Ramp: Shown on the screen as “C AP” (Active Power).
This programme allows you to ramp up the strength until it distracts you from
your labour pain. The strength is completely in your control (See page 3).
4. CONTRAINDICATIONS
Before using mamaTENS Mytime, please read the following
contraindications, cautions and warnings carefully.
Do not use TENS:
• If you have a heart pacemaker or have a heart rhythm problem.
TENS in the direct vicinity of a pacemaker may affect some models.
If TENS is applied on the front of the neck this can affect your heart rate.
Very strong TENS across the chest may cause an extra heartbeat.
• If you have epilepsy.
TENS may affect seizure threshold. You should consult your doctor prior to
using the mamaTENS unit.
• During the first three months of pregnancy.
It is not known whether TENS may affect foetal development
• On the abdomen in the later stages of pregnancy.
Stop use immediately if you experience unexpected contractions.
•
When driving, operating machinery, or similar actions needing fine control.
Loose pads, damaged leads, or sudden changes in contact may cause
brief involuntary muscle movements
• To mask or relieve undiagnosed pain.
TENS may delay diagnosis of progressive condition.

10
9
5. CAUTIONS & WARNINGS
Caution:
• Observe caution when using the mamaTENS at the same time as being
connected to monitoring equipment with body worn electrode pads; it
may interfere with the signals being monitored.
• Strong electromagnetic fields (electrosurgery/microwave cookers/mobile
phones) may affect the correct operation of this unit - See section 17. If it
appears to behave unusually, move it away from these devices.
• Use caution following recent surgical procedures.
Stimulation may disrupt the healing process.
Do not place electrode pads:
• On broken skin.
The pads could encourage infection.
• On skin which does not have normal sensation.
If the skin is numb, too great a strength may be used, which could result
in skin inflammation.
• On the front of the neck.
Could cause the airway to close, giving breathing problems. May cause
sudden drop in blood pressure (vasovagal response).
• Over the eyes.
May affect eyesight or cause headaches
• Across the front of the head.
Effect on patients who have had strokes or seizures is not known. May
affect sense of balance. The effects of stimulation of the brain are
unknown.
• Near malignant tumours.
In vitro experiments have shown that electricity can promote cell growth.
Do not:
• Ignore any allergic reaction to the electrode pads.
If a skin irritation develops stop using TENS and try a different type of
electrode. Alternative pads specially made for sensitive skin are available,
see section 16.
Also do not:
• Immerse your TENS unit in water or place it close to excessive heat.
It may cease to operate correctly.
• Attempt to open up the TENS unit.
This will invalidate the guarantee.
• Mix old, new or different types of batteries.
• Use this device with leads, electrodes, and accessories other than
those recommended by the manufacturer.
Performance may vary from specification.
IF IN DOUBT CONSULT YOUR MEDICAL PRACTITIONER, MIDWIFE
OR OBSTETRIC PHYSIOTHERAPIST

12
11
6. MAMATENS My Time CONTROLS On Button
To switch unit on: Press and hold down for
3 seconds. When the unit is switched ON
an audible “Beep” will be heard.
One Touch Memory Start
When switched on the unit will automatically
start in the programme which was being
used when it was switched off. The strength
returns to around 75% of the level that was
being used when the unit was switched off.
This dramatically simplifies the start up. To
stop the increase in strength at any time
during start-up, press any key once.
OFF Button
To switch unit off: Press and hold down the
button for 3 seconds and the unit will switch
off. Alternatively, press and release the OFF
button until the LCD screen displays 0; if you
press again it will switch the unit off. When
the unit switches OFF an audible double
“Beep” will be heard. NOTE: Always check
unit is OFF before removing pads.
Programmes
ON
Time in Labour
OFF
Boost Button
Strength
UP
Strength
DOWN

14
13
Programme Button
The MamaTENS “My Time” has specially
selected programmes. When you FIRST switch
on the unit, it starts in programme A. Each
time the “P” button is pressed and released
the programme changes, with the LCD
display showing the programme selected.
If you switch the unit back on within 2 hours
it will default to the programme last used.
If not it will return to programme A.
Strength UP Button
To increase strength: Press and hold down
until required strength is achieved. No
sensation will be felt through the pads until
the strength reaches at least the 2.5mA level.
Press and release to increase in 0.5mA steps
Strength DOWN Button
To decrease strength: Hold down button and
strength will decrease in 0.5mA steps.
BOOST Button
Press the Boost button when your contraction
begins, to change the mode from Int to Con.
Press again when you want to return to Con.
Time in Labour Button
Press this button to see how long you have
been using your MamaTENS “MyTime”, in
hours and minutes.
After 3 seconds, the display reverts to normal.
To reset the time to zero, hold down the key
for 5 seconds. The time automatically resets
when the MamaTENS “My Time” has been
turned off for more than 2 hours.
The time in hours and minutes

16
15
7. SCREEN DISPLAY Duration
Shows the length in seconds of your last contraction. The counter
starts when you press the Boost button to start “Con” mode to the
time you press it again to return to “Int” mode. It continues to show
the time until the start of your next contraction.
Interval
Shows the length of time in minutes and seconds between the start
of your last two contractions.
When Contractions are less than 5 minutes apart and they
last longer than 30 seconds, the display will pulse.
After 30 minutes, this pulsing will stop.
If you prefer not to see these time displays, you can turn them off:
Hold down Time in Labour and Strength Down buttons together for 3
seconds to turn off clock display.
Hold down Time in Labour and Strength Up buttons together for 3
seconds to turn on clock display.
Programme
Mode
Duration
seconds
Interval
minutes:
seconds
Strength

18
17
8. CONTENTS
• MamaTENS “My Time” maternity unit.
• Pack of maternity pads with integral mono leadwire
(item code E-CM50100IT-NEW).
• 2 x Batteries AA 1.5v (Type LR6).
• Instruction Manual.
• Neck Cord with quick release.
• Transit Pouch.
With RENTAL UNITS
Display box and Transit Pouch are replaced with a clear plastic rental
box
The unit comes with a pair of batteries already inserted
A Reply Paid Envelope for return of your rental unit
Before using your mamaTENS Mytime, please read this manual
thoroughly, especially the safety notes and precautions.
9. INSTALLATION OF BATTERIES
Remove Battery Cover
Press down in centre of battery cover and
slide backwards in direction of raised arrows.
Insert batteries
Ensure that the ribbon goes behind the
batteries to aid removal.
Ensure that the batteries are inserted the
right way as shown in battery compartment.
When the batteries are running low a low
battery indicator will show on the screen
(battery symbol).
The strength of the batteries will affect the
performance of the MamaTENS “My Time”
and the sensations will seem faint even on
the higher strength settings.
Disposal of batteries: Always dispose of
batteries safely. Do not throw onto a fire.
!

20
19
10. CONNECTING MONO LEADWIRE
Insert the Mono leadwire plug into the base
of the unit. Please note that it has been
designed to only insert one way.
11. POSITIONING THE PADS
Electrode pads must always be used in pairs,
so that the signal can flow in a circuit.
Correct positioning of the pads will give
maximum pain relief, so please study the
photo and then follow these instructions:
1. Make sure the unit is switched off before
applying the pads.
2. Make sure your skin is clean and dry
before applying the pads.
3. Carefully peel the pads off their plastic
liners. Do not pull on the leadwire.
Keep the liners in case the pads are to
be used again.
11. POSITIONING THE PADS (continued)
4. Place the top pair of pads (with white leads) either side of the
spine about 4 inches (100mm) apart from each other just below
your bra line.
5. Place the lower pair of pads (with black leads) either side of the
spine about 4 inches (100mm) apart and about 1 inch (25mm)
above the dimples at the base of the spine, just above
the buttocks.
NB: It is important to make sure that the pads are fitted correctly,
white being the top pair and black the bottom pair.

22
21
12. WHEN YOUR LABOUR STARTS
To get the best results from your MamaTENS “My Time” start using
it as soon as your labour starts.
1. Press and hold the ON Button until the screen lights up.
2. Check that the programme is “A int”.
3. Press and hold the Strength UP Button until you feel the
stimulation through the pads and the feeling is comfortable
then release.
4. The feeling through the pads will appear to lessen as your body
gets used to the stimulation. Press the Strength UP Button again until
you feel the stimulation at a comfortable level.
5. As you feel your contraction begin, press the Boost Button and
release. The programme will change to “A con” at the same level
of strength.
6. At the end of your contraction, press the Boost Button again
and the programme will change to “A int”, again at the same
strength level.
7. Remain in programme “A” for as long as possible, switching
between “A int” and “A con” as necessary and simply increasing
the strength as your body accomodates.
8. If the pain goes deep, normally when you are in the later stages
of labour, then in between contractions press the Programme button
and the unit will go to “B int” at zero strength. The strength will
then gradually increase to about 75% of your previous setting. Press
and hold Strength UP Button until you feel the stimulation through
the pads and the feeling is comfortable then release. Increasing the
strength as your body becomes used to the stimulation.
9. As you feel your contraction begin press the Boost Button and
release. The programme will change to “B con” at the same level
of strength.
10. At the end of your contraction press the Boost Button again and
the programme will change to “B int”, again at the same strength.
11. Continue to go from “B int” to “B con” either until the end of
your labour or just before the end of your labour, go back to
programme “A”. To return to programme “A” press the Programme
Button twice more.
N.B. You will possibly be aware that the stimulation is slightly
greater from the higher pair of pads (Ch1) is greater than the
lower pair set of pads (Ch2). This is intentional and part of the
therapy.

24
23
13. EXTRA PAIN RELIEF
If the level of pain becomes extreme or if you did not start using the
unit sooner enough to allow for the full endorphin release then it is
suggested that you go to programme “C AP”.
ACTIVE POWER
In this programme the strength “Power Ramps” up and which brings
into play “Brief Intense” pain relief. It also acts as a distraction.
In between contractions press the programme button until the screen
displays “C” in the top left-hand corner. The strength will be at zero.
Press the Strength UP button until the stimulation is comfortable. As
the contraction begins press and hold down the Boost button so that
“AP” is displayed on the screen. This will ramp up the strength. Hold
down the button until the stimulation is as strong as you can bear. At
that moment release the button and the strength will immediately
start to fall. If you press and hold the button now, it will sustain the
strength at this level as long as you want. When you release the
button, strength will return to the level it was before you first pressed
the Boost button.
14. GENERAL INFORMATION
TRIAL RUN
It is recommended that you have a trial run with your MamaTENS
“My Time” before your labour starts so that you know how it works,
where to put the pads and what the stimulation in the programmes
feels like. After your trial run, return the pads to the clear plastic film
and store in the re-sealable bag. Make sure that the MamaTENS “My
Time” is switched off before removing the pads.
QUICK RELEASE NECK CORD
Your MamaTENS “My Time” is supplied with a quick release neck
cord. The neck cord allows for the unit to be hung around your neck
if required. To fit the neck cord simply pass it through the loop at the
top of the unit.
CAUTION: Do not substitute string or a regular necklace as such
items may not open in the event of a snagging.
EASY START – ONE TOUCH MEMORY
The MamaTENS “My Time” has intelligent memory that enables the
unit to remember the last programme used, and reverts to it at the
touch of one button. At the same time, the strength gently ramps up
to around 75% of the level last used. This memory start will not occur
if the batteries have been replaced.

26
25
PAD ALARM
The MamaTENS “My Time” monitors the condition of the pads
during use and the quality of the connection to the body. If
either deteriorates to a point where the stimulation is affected
detrimentally, the word “PADS” will flash on the screen and an
audible beep will be heard. This will probably occur if one of the pads
has come away from your body. Check all four pads. If a pad does
partly or entirely come away from the body, the Comfort Strength
Control feature automatically lowers the stimulation proportionally to
reduce any discomfort you may feel. When the pads are put back, the
stimulation will automatically return to the original level.
The “PADS” alarm only works when the strength exceeds 5.0mA.
PADS
The pads supplied are MamaTENS 50x100mm superior multi use self
adhesive pads (item no: E-CM50100IT). The pads and mono leadwire
are moulded together to simplify use.
Please Note:
i) Do not immerse the pads in water as they are water-soluble.
ii) Even though the pads are hypo-allergenic, on rare occasions
skin irritation can occur. If this is significant, stop using the unit and
remove the pads. You can call our helpline for further advice.
iii) Do not apply pads to broken skin, or to skin which does not have
normal sensation.
POST NATAL USE
If you are in pain following the birth, you can obtain further releif
from the MamaTENS “My Time”. It is effectve for afterbirth pain,
episiotomy, tears and back pain.
USE DURING AND AFTER CAESAREAN
Even if you decide to have a caesarean you can still use the
MamaTENS “My Time”, during the early part of your labour, either at
home or at the hospital.
For pain relief following a caesarean, place the pads where you get
the best relief, avoiding the immediate area of the scar.

28
27
BATTERY REMOVAL AND REPLACEMENT
When the batteries need to be changed, the low battery sign,
“BATT”, will be displayed on the screen. To remove batteries, pull
gently on the ribbon that goes around the back of the batteries.
Battery type: ONLY use either 1.5 AA alkaline batteries or NiMH AA
rechargeable batteries.
NEVER attempt to recharge an alkaline battery - There is a risk
of explosion. DO NOT mix batteries of different types.
Disposal
Always dispose of batteries as per government guidelines
(see section 18). Never put batteries in a fire, nor try to disassemble
them. Do not attempt to revive alkaline batteries by heating, charging
or other means.
Warning
• Keep batteries out of the reach of small children.
• If battery leakage occurs and comes in to contact with the skin or
eyes, wash thoroughly with lots of water.
• Seek medical advice immediately if you believe a cell has
been swallowed.
HELPLINE
A helpline is available, Monday to Friday. Call: 01372 72 34 34
Or Email: [email protected]
!
RETURNING YOUR RENTAL UNIT
If you rented your mamaTENS MyTime your machine should have
been sent to you three weeks before your due date.
The rental period is for five weeks, but if you need more time just call
us before the end of the rental period and we’ll arrange an additional
two weeks absolutely free of charge.
Sending your maternity TENS machine back at the end of the rental
period is very easy.
•
You’ll have received a pre-paid envelope with your machine so
simply put the unit, neck cord, unused batteries and manual back
in the box - no need to include the lead wires and pads – pop the
box into the envelope and drop it in at the post office.
•
You’ll need to ask for a proof of posting certificate at the post
office but it’s all free of charge and very straightforward.
•
If you rented by purchasing a voucher or DVD, do NOT return the
unit to the shop where you made the purchase. It should only be
returned in the envelope provided.

30
29
15. GUARANTEE
(Refers only to MamaTENS “MY Time” units that have been
purchased).
Your unit is guaranteed for two years from the date of purchase.
If a fault develops, return the unit to MamaTENS at the address
on the back cover, together with a copy of your invoice and details
of the problem.
The guarantee does not cover the batteries, electrode pads or
mono leadwire.
Please note that the Guarantee is invalidated if
i) incorrect batteries have been fitted.
ii) the unit has been immersed in water, maltreated or
tampered with.
iii) the unit has not been used with genuine MamaTENS or
Tenscare electrode pads.
16. TROUBLESHOOTING
Problem Possible causes Solution
No display Flat batteries Replace batteries
Batteries inserted
incorrectly
Check
Damaged battery
contacts
Contact supplier
Low battery display Low batteries Replace batteries
No sensation Incorrect connection Have you applied both
electrode pads (per lead
wire) to ensure a complete
circuit?
Not strong enough Increase strength
Most users will feel
something at a setting
below 20
PAD alarm Incorrect connection Ensure machine is attached
to your body correctly
Lead faulty/damaged Purchase replacement if
necessary
If the above review has failed to resolve your problem, call TensCare
or your local dealer (address on back cover) for advice.
Or if you have any questions or need more information you can
contact TensCare at anytime via our website, www.tenscare.co.uk
or by phoning 01372 723 434.

32
31
17. CONSUMABLES AND SERVICING
(Refers only to MamaTENS “MY Time” that have been purchased)
To ensure reliability and hygiene, use only genuine rectangular electrodes
with integral leads:
For units after 5140001, we are using part number E-CM50100IT-NEW
For units before 5140001, we are using part number E-CM50100IT
Please note: these are the part numbers according to the TensCare website.
These are available from either your supplier or by ringing
01372 723434 or by going to www.tenscare.co.uk.
Please ensure that you order the correct pads.
Batteries can also be purchased in the same way or on the high street.
They are AA 1.5v alkaline batteries.
For servicing please return the unit to: TensCare Ltd, 9 Blenheim Road,
Longmead Business Park, Epsom, Surrey KT19 9BE. Please ensure that you
enclose your name, address and contact telephone number so that you can
be contacted and informed about any problem and any costs involved.
Expected Service Life
• The machine will often last for more than 5 years, but is guaranteed for
2 years.
Accessories (leads, pads, and batteries) are not covered by the guarantee.
• Lead life depends greatly on use. Always handle the leads with care.
• Pads should last 12-20 applications, depending on skin condition and
humidity.
• AA alkaline batteries should last about 48 hours continuous use.
18. DISPOSAL OF WASTE ELECTRICAL AND
ELECTRONIC PRODUCTS (WEEE)
(Refers only to MamaTENS “MY Time” that have been purchased)
One of the provisions of the European Directive 2002/96/CE is that
anything electrical or electronic should not be treated as domestic
waste and simply thrown away. To remind you of this Directive all
affected products are now being marked with a crossed-out wheelie
bin symbol, as depicted below.
To comply with the Directive you can return your old electro-therapy
unit to us for disposal. Simply print a postage-paid PACKETPOST
RETURNS label from our websites www.mama-tens.info or www.
tenscare.co.uk, attach this to an envelope or padded bag with the
unit enclosed, with your name and address and a note to say that
this machine is being returned for disposal, and post it back to us.
Upon receipt we will send your old device for components recovery
and recycling to help to conserve the world’s resources and minimise
any adverse effects on the environment.

34
33
19. TECHNICAL SPECIFICATION
Waveform Asymmetrical Bi-Phasic
Amplitude (over 500 ohm load) 70mA zero to peak +ve in
steps of 0.5mA
Constant current over 500-1500 Ohm
Constant voltage when
PADS signal shows.
Output plug Fully shielded: touch proof mini USB
Channels Dual Channel
Batteries 2 x AA Alkaline (Two AA batteries)
OR rechargeable NiMH
Weight 90 gms without batteries
Dimensions 110 x 53 x 30mm
Safety Classification Internal power source. Type BF
Designed for continuous use.
No special moisture protection.
Environmental Specifications:
Operating: Temperature range: 5 to 40C: 15 to
93% RH non-condensing
Storage: Temperature range: -25-+70C
RH 93% Humidity non condensing
Contact Duration: at least 10 minutes
Equipment providing a degree of
protection against electric shock,
with isolated applied part.
This symbol on the unit means
“Refer to Instruction Manual”
The unit is not water resistant, and
should be protected from liquids.
NB: The electrical specifications are nominal and subject to variation
from the listed values due to normal production tolerances.
Programme Settings
Display Mode Frequency/Pulse Width
A1 Burst 80Hz 150µs
A1 Boost Continuous 80Hz 150µs
B2 Burst 150Hz 150µs
B2 Boost Continuous 150Hz 150µs
C3 Ramp 80Hz 250µs

36
35
The mamaTENS is intended for use in the electromagnetic environment specified below. The customer
or the user of the mamaTENS should assure that it is used in such an environment.
Immunity test IEC 60601
test level
Compliance
level
Electromagnetic environment – guidance
Conducted RF
IEC 61000-4-6
3 Vrms
150 kHz to
80 MHz
3 Vrms
Portable and mobile RF communications equipment should be
used no closer to any part of the mamaTENS, including cables,
than the recommended separation distance calculated from
the equation applicable to the frequency of the transmitter
Recommended separation distance 3V
d = 1.2√ P 80M Hz to 800MHz
d = 2.3√ P 800MHz to 2.5GHz
where P is the maximum output power rating of the transmitter
in watts (W) according to the transmitter manufacturer and d is
the recommended separation distance in meters (m).
Field strengths from fixed RF transmitters, as determined
by an electromagnetic site survey, should be less than the
compliance level in each frequency range. Interference
may occur in the vicinity of equipment marked with
the symbol on the left of this box
Radiated RF
661000-4-3
3 V/m
80 MHz to
2,5 GHz
3 V/m
NOTE 1 At 80 MHz and 800 MHz, the higher frequency range applies. NOTE 2 These guidelines may not
apply in all situations. Electromagnetic propagation is affected by absorption and reflection from structures,
objects and people.
a. Field strengths from fixed transmitters, such as base stations for radio (cellular/cordless) telephones
and land mobile radios, amateur radio, AM and FM radio broadcast and TV broadcast cannot be predicted
theoretically with accuracy. To assess the electromagnetic environment due to fixed RF transmitters, an
electromagnetic site survey should be considered.
If the measured field strength in the location in which the mamaTENS is used exceeds the applicable RF compliance
level above, the mamaTENS should be observed to verify normal operation. If abnormal performance is observed,
additional measures may be necessary, such as re-orienting or relocating the mamaTENS.
b.Over the frequency range 150 kHz to 80 MHz, field strengths should be less than 3 V/m.
Recommended separation distances between portable and mobile RF communications equipment and
the mamaTENS.
The mamaTENS is intended for use in an electromagnetic environment in which radiated RF disturbances are
controlled. The customer or the user of the mamaTENS can help prevent electromagnetic interference by maintaining
a minimum distance between portable and mobile RF communications equipment (transmitters) and the mamaTENS
as recommended below, according to the maximum output power of the communications equipment.
20. EMC PRECAUTIONS
Use special precautions regarding EMC according to the information provided below. Other
portable and mobile RF communications equipment can affect performance. Do not use
when adjacent to or stacked with other electrical equipment. Use of leads or pads other
than those listed in section 18 may affect EMC performance.
Guidance and manufacturer’s declaration – electromagnetic emissions
The mamaTENS is intended for use in the electromagnetic environment specified below. The customer
or the user of the mamaTENS should assure that it is used in such an environment.
Emissions test Compliance Electromagnatic environment - guidance
RF emissions CISPR 11 Group 1 The mamaTENS uses RF energy only for its
internal function. Therefore, its RF emissions
are very low and are not likely to cause any
interference in nearby electronic equipment
RF emissions CISPR 11 Class B
The mamaTENS is suitable for use in domestic
establishment and in establishment directly
connected to a low voltage power supply
network which supplies buildings used for
domestic purposes.
Harmonic emissions IEC61000-3-2 Not applicable
Voltage fluctuations/flicker emissions
IEC 61000-3-3
Not applicable
The mamaTENS is intended for use in the electromagnetic environment specified below. The
customer or the user of the mamaTENS should assure that it is used in such an environment.
Immunity test IEC 60601 test level Compliance level Electromagnetic
environment guidance
Electrostatic discharge (ESD)
IEC 61000-4-2
±6 kV contact
±8 kV air
±6 kV contact
±8 kV air
Floors should be wood,
concrete or ceramic tile
If floors are covered with synthetic material, the relative humidity should be at least 30%.
Electrical fast transient /burst
IEC 61000-4-4
±2 kV for power supply lines
±1 kV for input/output lines
Not applicable Not applicable
Surge mode IEC 61000-4-5 ±1 kV differential
±2 kV common mode
Not applicable Not applicable
Voltage dips, short
interruptions and voltage
variations on power supply
input lines IEC 61000-4-11
<5 % UT (>95 % dip in UT) for 0,5 cycle
40 % UT (60 % dip in UT) for 5 cycles
70 % UT (30 % dip in UT) for 25 cycles
<5 % UT (>95 % dip in UT) For 5s
Not applicable Not applicable
Power frequency (50/60 Hz)
magnetic field. IEC 61000-4-8
3 A/m Not applicable Not applicable
NOTE UT is the a.c. mains voltage prior to application of the test level.
Rated maximum output power
of transmitter W
Separation distance according to frequency of transmitter M
150kHz to 80MHz
d=1.2√ P
80 MHz to 800 MHz
d=1.2√ P
800MHz to 2.5GHz
d=2.3√ P
0.01 0.12 0.12 0.23
0.1 0.38 0.38 0.73
1 1.2 1.2 2.3
10 3.8 3.8 7.3
100 12 12 23
For transmitters rated at a maximum output power not listed above, the recommended separation distance d≠ in meters
(m) can be estimated using the equation applicable to the frequency of the transmitter, where P is the maximum output
power rating of the transmitter in watts (W) according to the transmitter manufacturer. NOTE 1 At 80 MHz and 800 MHz,
the separation distance for the higher frequency range applies. NOTE 2 These guidelines may not apply in all situations.
Electromagnetic propagation is affected by absorption and reflection from structures, objects and people.