Terex SmartPTO User manual

TEREX UTILITIES TECHNICAL SUPPORT TEAM
PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]
MODEL(S): TOOLS NEEDED:SERVICE CALL:
NO.
EV SMARTPTO QUICKSTART
GUIDE
INTERNATIONAL EV CHASSIS NONE
EV SMARTPTO QUICKSTART GUIDE
192

DANGER
Failure to obey the instructions and safety
rules in the appropriate Operator’s Manual and
Service Manual for your machine will result in
death or serious injury.
Many of the hazards identied in the
Operator’s Manual are also safety hazards
when maintenance and repair procedures are
performed.
DO NOT PERFORM
MAINTENANCE UNLESS:
√You are trained and qualied to perform
maintenance on this machine.
√You read, understand and obey:
•manufacturer’s instructions and safety rules
•employer’s safety rules and worksite
regulations
•applicable governmental regulations
.
√You have the appropriate tools, lifting
equipment and a suitable workshop.
The information contained in this Tech Tip is a
supplement to the Service Manual. Consult the
appropriate Service Manual of your machine for
safety rules and hazards.
PAGE 2 OF 7
TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0
TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0
©TEREX UTILITIES. ALL RIGHTS RESERVED

PAGE 3 OF 7
CONTENTS
TECH TIP#192
TOC
4| Verify high voltage switches
| Turn the ignition key ON
STEP 1 - STEP 2
5| Parking brake
| E-stop
STEP 3 - STEP 4
6| Viatec system
STEP 5 - STEP 6
TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0
STEP 2
Turn the ignition key to the ON position. The truck cannot be in the drive mode.
The cluster screen should not have a drive symbol on it. If the drive symbol is visible, cycle the
ignition to the ON position to get the chassis out of drive mode. Figure 3 shows the screen in drive
mode and Figure 4 shows the screen not in drive mode.
FIGURE 1
STEP 1
Verify that both high voltage shutoff switches are in the ON position. One is located in the cab, the
other is on the backside of the battery box. If both switches are off, turn on the cab switch rst.
FIGURE 2
FIGURE 3
PAGE 4 OF 7

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0
STEP 3
Verify that the parking brake is engaged (pulled
out), and the truck is in neutral.
FIGURE 4
STEP 4
Verify that the e-stop is pulled out on the
Viatec system. The e-stop Is located on a
square weldment behind the last curbside
compartment.
PAGE 5 OF 7

TECH TIP 192 | RELEASED 11.17.2022 | VERSION 1.0
STEP 5
Verify that the Viatec symbol on the bottom left
of the screen displays detected. If the system
is detected, press the PTO button.
FIGURE 8 FIGURE 9
FIGURE 7
STEP 6
Verify that under the viatec symbol the wording
changed from Detected to Allowed. This lets the
operator know that all the interlocks have been
met to allow the system to run. Figure 8
Then press the E-PTO buttom. It will turn
yellow during start-up and then will turn green.
Once the motor can be heard turning, the smart
PTO system is ready to use.
Figure 9
If any faults are detected, consult the
manufacturer’s manual for troubleshooting. If
you have any questions call 1-844-TEREX4U
(1-844-837-3948) or email utilities.service@
terex.com
PAGE 6 OF 7

FOR FURTHER ASSISTANCE,
CONTACT THE TEREX UTILITIES TECHNICAL SUPPORT TEAM
PHONE: 1-844-TEREX4U (1-844-837-3948) | EMAIL: [email protected]