TESmart HSW1601A10 User manual

www.tesmart.com
1
16x1 HDMI Switch
# HSW1601A10
The 16 ports HDMI switch HSW1601A10, allows up to 16 Ultra HD sources to be routed to
one Ultra HD display. Support resolutions up to 4K (3840 x 2160 @ 30Hz). Deep Color,
3DTV pass-through, and lossless audio formats such as LPCM 7.1, Dolby TrueHD, and
DTS-HD Master Audio are also supported. Support automatic input source detection, when
attach new input device to the switch, the switch will switch to last plugged in source
automatically.
With EDID emulators in each input port, keep PCs always having correct display information,
prevent display settings from changing while switching input ports.
Features
With EDID emulators in each input port, keep PCs always having correct display
information
Support hot plug, connect or disconnect devices to the HDMI switch in any time and
without turn off devices
Support auto switching to monitor computers in a specified time interval
Support front panel buttons, IR signals, RS232 serial commands or IP commands to
control HDMI switch
Support resolution up to 3840*2160@30Hz
Auto input detect and switch
Support DVI-D single link sources and displays with the use of HDMI-to-DVI adapters
Packing list
1 * 16x1 HDMI Switch
1 * DC 12V 2A Power Adapter
1 * IR Remote Control
1 * IR Receiver Cable
1 * 3 Pins Connector (For RS232)
2 * Rack-ears
1 * Quick-Start Guide

www.tesmart.com
2
Panel descriptions
1. IR receiver extension cable input
2. DC 12V Power Adapter
3. 3 Pins jack for RS232 console
4. HDMI output port
5. HDMI input ports
6. Auto scan time interval settings
[MIN]: Press button [MIN] to loop between 0~59 minutes.
[SEC]: Press button [SEC] to loop between 0~59 seconds.
[Set]: After setting minutes and seconds by buttons [MIN] and [SEC], press button [Set] to enter final
scan time interval setting.
7. Status indicator:
Green LED: Auto scanning mode
Red LED: Normal status
8. IR receiver
9. LED display: display current selected input source
10. Keypad:
[1~9]: Press these buttons to directly select input 1~9 sources.
[0/Close]: Press this button directly will turn on or turn off the display out; Press [1+] then [0/Close] to
select input 10
[Scan]: Press this button to start or stop automatically scan between input 1 to input. The interval time
can be set by buttons [Set], [MIN], [SEC] as described above.
11. LAN: TCP/IP console interface
12. Power switch: Turn on or off the power.

www.tesmart.com
3
Connection diagram

www.tesmart.com
4
Specification
HSW1601A10
16x1 HDMI Switch
Functionality:
Auto Scan
Yes
Port selection
Front panel buttons
Yes
Keyboard hotkeys
No
IR remote control
Yes
Console commands
RS232 / IP
Technical:
Max. Resolution
3840x2160@30Hz
Auto to get EDID
Yes
Data rate
10.2 Gbps
Auto scan interval
5~3600 Seconds
Beep Sound
On/Off
OSD
No
Console ports
RS232
1 * 3 Pins jack
LAN (TCP/IP)
1 * RJ45
IR extension input
1 * AUX
Input
16 * HDMI Type A
Output
1 * HDMI Type A
ESD protection
Human body model - ±8kV (Air-gap discharge)
Mechanical:
Chasing material
Metal
Product
Dimension
440 (L) x 150 (W) x 44.5 (H) mm
Weight
1700g
Item
Dimension
488 (L) x 123 (W) x 186 (H) mm
Weight
2287g
Carton
Dimension
505 (L) x 280 (W) x 395 (H) mm
Quantity
4pcs
Total Weight
9.898kg