Texecom Premier Elite AM 360DT User manual

Installation Manual
Premier Elite AM 360DT
INS622-2

INS622-2 2/13
Content
1.0 Instruction Manual 3 .................................................................................................................
2.0 EN: Installation Sheet 7 ............................................................................................................

INS622-2 3/13
1.0 Instruction Manual
1)________________________________________________________
2)________________________________________________________

INS622-2 4/13
3)________________________________________________________

INS622-2 5/13

INS622-2 6/13
4)________________________________________________________
5)________________________________________________________

INS622-2 7/13
6)________________________________________________________
2.0 EN: Installation Sheet
Description
The Premier Elite AM 360DT is a ceiling mount dual technology detector, which is
designed to detect a movement of an intruder, and to activate an alarm on a

INS622-2 8/13
control panel. The product must be connected to a listed burglar system
compatible control unit or power supply unit, which provides a supply voltage
between 9 and 15 VDC as well as a minimum 4 hours of standby power.
Installation guidelines
The technology used in these detectors resists false alarm hazards. However,
avoid potential causes of instability such as:
Avoid mounting the detector where objects may interfere with the anti-
masking function (<1m), above doors, near curtains etc.
The detector should not be mounted in direct sunlight.
Not suitable for outdoor use.
To install the detector:
1. Unwind the screw on the side of the detector until loose; the screw will be

INS622-2 9/13
retained in the product (see Figure 1, item 1).
2. Lift detector lid out from the base and off the lugs at the opposite end to the
screw (see Figure 1, item 2).
3. Fix the base to the ceiling between 2.4 m and 3.6 m (8 and 12 ft) from the floor.
For flat mounting use a minimum of 2 screws (DIN 7998) in any of the available
positions (see Figure 2). Rear tamper pull-out needs to be secured to the mounting
surface to meet Grade 3 requirements.
4. Wire the detector (see Figures 4 and 5).
5. Select the desired option settings (see Figure 6).
On power-up the detector will temporarily enter an auto-optimisation mode to
adapt to its environment. This will be shown by the LED’s flashing in
sequence. Allow 3 minutes for the optimisation to complete.
During optimisation ensure that there are no obstructions in close proximity
(<1m) to the detector that will not be present during normal operation, as
this could trigger a false masking signal.
Triple End-Of-Line (T-EOL) (see Fig. 4)
The detector is designed to be connected to a single zone on control panels which
feature Triple End-Of-Line compatibility. Alarm, Tamper, Fault and Masking are
signalled on one pair of wires. To aid installation the resistor values can be
selected via the jumpers. All the connections are normally closed. Masking is

INS622-2 10/13
signalled by the alarm and fault relays opening simultaneously, this can
be done by changing Option 3 jumper so only the fault relay is opened.
(see Fig.6)
Fault Monitoring - A fault will be indicated by one of the following:
Supply input voltage out of specification1.
PIR sensor malfunction / microwave malfunction2.
The fault will remain until the power is cycled off/on.
This detector is capable of performing a self-test. There are two types of self-test;
a local self-test and a remote self-test.
Self-Test
To meet the requirements of EN50131-2-4 this detector is capable of performing a
self-test. There are two types of self-test, a local self-test and a remote self-test.
Local Self-Test
Local self test is controlled by the detector and runs periodically to test the
functionality of the circuitry. Setting the Local Self Test Jumper to DISABLED will
disable this function. If the test is passed no indication is shown but if it fails then a
fault will be signalled to the panel and the LED lights orange (if enabled). The fault
will remain until the power is cycled off/on.
Remote Self-Test
This test is initiated at the control panel. If the test is passed the green LED pulses
twice in quick succession and alarm signalled but if it fails then a fault will be
signalled to the panel and the LED lights orange (if enabled). The fault will remain
until the power is cycled off/on. The panel is required to set the ‘TEST’ terminal low
(0V) for activation of Remote Self Test.
Walk Test
This test is initiated at the control panel. If this terminal (RLED) is set low by the
panel (0V) the unit will enter walk test mode (when LED indication J5 is disabled).

INS622-2 11/13
Wiring
For the ex-factory settings, see Figure 5 & 6. Walk test (RLED) voltage - Open
Collector, 0 V active. Remote Test - Open Collector, 0 V active.
LED Indication (see Fig. 9)
Please Note: the Alarm condition has precedence in the event of multiple
conditions being active.
Regulatory information
Supplier:Texecom Ltd, St. Crispin Way, Haslingden, Lancashire, BB4 4PW, UK.
Security grade: EN Grade 3
Environmental class: Class II
Standards: EN 50131-2-4
European Directives
2004/108/EC (CE directive): Hereby, Texecom declares that this device is in
compliance with the essential requirements and other relevant provisions of
Directive 2004/108/EC.
2011/65/EU (RoHS Directive): Hereby, Texecom declares that this device does
not contain lead, mercury, cadmium, hexavalent chromium, polybrominated
biphenyls (PBB) or polybrominated depheny ethers (PBDE) in more than the
percentage specified by EU directive 2011/65/EU, except exemptions stated in EU
directive 2011/65/EU annex.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.

INS622-2 12/13
Maintenance: To be tested yearly by the installer
Warranty: 2 year replacement warranty
The Premier Elite AM 360DT is not a complete alarm system, but only its part.
Therefore Texecom does not accept any responsibility or liability for any damage
that is claimed to be a result of an incorrect functioning of the Premier Elite AM
360DT detector. Texecom reserves the right to change the specification without a
prior notice.

INS622-2 13/13