Texecom Impaq SC-W User manual

Installation Manual
Impaq SC-W
INS876-1

INS876-1 2/15
Content
1.0 Introduction 3 ............................................................................................................................
2.0 Initial configuration & learning on 5 ......................................................................................
2.1 DIP switch configuration 5 ......................................................................................................
2.2 Additional inputs 1&2 6 ..........................................................................................................
2.3 Learning the device to the system 6 ......................................................................................
2.4 Using the device with a roller shutter contact 7 .....................................................................
3.0 Wireless range test 8 ................................................................................................................
4.0 Mounting 8 ..................................................................................................................................
4.1 Device mounting 8 .................................................................................................................
4.2 Magnet positioning 9 ..............................................................................................................
5.0 Setting the shock sensitivity 12 ..............................................................................................
6.0 Specifications 14 ........................................................................................................................
7.0 Legal Information 14 .................................................................................................................

INS876-1 3/15
1.0 Introduction
The Impaq SC-W is a wireless shock sensor with an on board magnetic contact. The
product can also be used with an externally wired magnetic contact and has an
additional facility for use with window shutter movement detectors.
When using Premier Elite Firmware Version 2.10 and above the dedicated
Ricochet learn menu can be accessed via the omit key when in the Engineers
menu. For all other firmware versions please refer to the Premier Elite 8XP-
W/32XP-W Installation Manual.
See the Premier Elite 8XP-W/32XP-W Installation Manual for details of how to
change the device attributes and learning.
Figure 1 shows the key parts of the device that are used for configuration.
Figure 1

INS876-1 4/15

INS876-1 5/15
Icon Item
A Function select DIP switch
B Battery
C Magnet sensor
D Sensitivity selection button
E External input terminal block
2.0 Initial configuration & learning on
2.1 DIP switch configuration
Each switch controls one sensor (shown below). The DIP switches should be
changed after the device is learnt to the system (unless you are only using the
device as a Ricochet wireless repeater).
DIP Switch Controls
M Magnetic contact sensor
S Shock sensor
T1 Terminal 1
T2 Terminal 2
Note 1: Terminal 2 functions as a tamper input. To enable this, configure the DIP
switch labelled T2 to the ON position.
Note 2: To comply with EN50131-2-8, move ONLY DIP switch "S" to the ON
position. To comply with EN50131-2-6, move ONLY DIP switch "M" to the ON
position.

INS876-1 6/15
2.2 Additional inputs 1&2
The Impaq SC-W has 2 additional inputs. These may be used for any normally
closed output device and utilise wireless transmission to the receiver. Typical
examples for use are:
Any locally powered device with a normally closed output e.g. Smoke
detectors, Glass Break detectors, Movement Sensors, Flood detectors etc.
Any non-powered normally closed output device, e.g. Specialist magnetic
contacts, fixed PA buttons etc.
2.3 Learning the device to the system
To learn the device to the system:
Select an empty zone slot for the device and put the system into learn mode.
To power up press and hold the sensitivity button for 3 seconds.
The LED will flash pink while it communicates to the receiver. The LED will
turn green if the device has successfully learnt onto the system. If the LED
turns red the learn has failed.
Check the system is in learn mode.
Move closer to the panel or expander.
Ensure you are learning the device to an “empty” zone.
NOTE: The device will provide a low battery signal to the panel, once this signal is
displayed the battery should be replaced within 30 days.
Configure the DIP switches so that the sensor/s you want to use are set to the
ON position (see example in figure 3).
Figure 3

INS876-1 7/15
2.4 Using the device with a roller shutter contact
The Impaq SC-W can be used with retracting cord contacts to protect door and
window roller shutters. These are particularly useful when the shutter is left in a
partially open position but still needs to be protected against forced entry. The
device is compatible with all microswitch 2 wire roller shutter contacts.
To learn the device with a roller shutter contact:
Connect the roller shutter contact to terminal 1.
Complete the learn process by following the steps in section 2.3.
Configure the DIP switch labelled T1 to the ON position.
To test the device:
Once the device is learnt to the system, pull the cord on the roller shutter
contact.
The device will treat 6 or more pulses within a 10 second period as an
activation.

INS876-1 8/15
3.0 Wireless range test
The wireless range test is available for the first hour after power up or while
the system is in walk test mode – see Premier Elite 8XP-W/32XP-W installation
manual.
With the device in position, press and hold the sensitivity button for 3
seconds.
The LED will flash pink and turn green when a wireless connection is
confirmed.
Should the LED turn red move the device away from metal objects, closer to
the receiver or add more devices to the mesh network.
Once the device leaves commission mode, the device will not show any
status LED’s.
4.0 Mounting
4.1 Device mounting
Select the intended mounting position. The device can be installed in any
mounting orientation.
Open the device cover and remove the PCB using a screwdriver (see figure 4)
To ensure product compliance with EN50131, fix both the detector and
the rear tamper insert to the mounting surface using the following type of
screws:
Head Type: Counter Sunk flat head
Head Diameter: 5.3-6.8mm
Screw Diameter 2.9-3.2mm
Screw length: 15.8-24.5mm
NOTE 1: If the product is mounted on concrete suitable wall plugs should be used.
NOTE 2: If using the magnet, the same screw types should be used for
installation.
Figure 4

INS876-1 9/15
4.2 Magnet positioning
Once the device has been mounted, position the magnet so the notch is
aligned with either of the arrow markers on the sides of the PCB, the LED will
pulse green indicating a secure state.
The magnet can be installed on either side of the device. However, greater
sensitivity is achieved by placing the magnet at the bottom right of the
device and aligning the notch and the arrow. (see figure 5 for magnet
distances)
If the device LED pulses red, move the magnet closer to the device until the
LED turns green.

INS876-1 10/15
The LED indication for magnet positioning is time limited whilst the system is
in commission mode.
Figure 5
Side of
Device Axis Approach Min (mm) Removal Max (mm)

INS876-1 11/15
Right
X 33 36
Y+ 6 7.5
Y- 6 8
Z+ 50 52
Z- 35 41
Left
X 24 30
Y+ 5 7
Y- 7 8.5
Z+ 52 56
Z- 27 33
Once the correct position has been located fix the magnet in place (see figure
6).
Figure 6

INS876-1 12/15
5.0 Setting the shock sensitivity
Within 10 minutes of learning the device (or by activating walk test mode),
double press the sensitivity button and the LED will flash blue defaulting to

INS876-1 13/15
sensitivity setting 2. There are 5 sensitivity settings from 1 to 5 with 1 being
the least sensitive (slowest flash rate) and 5 the most sensitive. Each press of
the button will change the sensitivity indicated by the flash rate of the blue
LED, cycling from slow to fast and finally back to slow after 5 presses.
Recommended Sensitivity Setting* Material Radius
1 Wood 1m
2 Framed Glass Window 1m
5 Concrete 0.5m
Before testing the device, press and hold the button (3 secs) to set the
desired sensitivity setting.
The LED will turn green for confirmation at which point the device is ready for
impact testing.
On impact test, if the LED turns red, the selected sensitivity setting is
appropriate for the installation. If it doesn’t turn red, select the next
sensitivity and repeat the test. Continue until a level is selected whereby the
device LED turns red on impact.
*Based on the testing requirements of EN50131-2-8 : 2016

INS876-1 14/15
6.0 Specifications
Specifications
Alarm System
EN50131-2-8:2017, EN50131-2-6:2008,
EN50131-5-3:2017, EN50131:2006+A2:2017,
PD6662:2017, Grade 2 Class II
Product Type & Frequency Band
GJAA1000 868.2 – 868.4MHz
GJAA2000 866.2 – 866.4MHz (Not CE approved)
GJAA3000 433.3 – 433.7MHz
Receiver Category 1, Class 2
Receiver LBT Listen Before Talk
Transmitter Duty Cycle <1%
Max RF Power 10mW
Low Voltage Signal 2.50V
Operating Voltage 3V
Maximum Current 12mA
Quiescent Current 19μA
Relative Humidity 0 - 95% non-condensing
Operating Temperature -10°C to 55°C
Weight 80g
Dimensions 130mm x 26mm x 25mm (magnet 57mm x
11.5mm)
7.0 Legal Information
Supplier: Texecom Ltd, Haslingden, Lancashire, BB4 4PW, UK.
Made in England
WEEE Directive: 2012/19/EU (WEEE Directive): Products marked with this symbol

INS876-1 15/15
cannot be disposed of as unsorted municipal waste in the European Union. For
proper recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points. For
more information see: www.recyclethis.info.
Maintenance: Test yearly by the installer.
Warranty: 2 year replacement warranty (excludes battery).
As the Impaq SC-W is not a complete alarm system, but only a part thereof,
Texecom cannot accept responsibility or liability for any damages whatsoever
based on a claim that the Impaq SC-W failed to function correctly. Due to our
policy of continuous improvement Texecom reserves the right to change
specification without prior notice.
Domestic Use: If this product is installed within reach of children the screw cover
should not be fitted as this could cause a choking hazard.
Hereby, Texecom declares that the equipment type : GJAA1000 and GJAA3000, is
in compliance with the Radio Equipment Directive (RED) 2014/53/EU and the
Electo-magnetic Compatibility (EMC) Directive 2014/30/EU.
The full EU declaration of conformity is available here.
Certified by Telefication B.V.