Texecom Prestige Orbit QD User manual

Prestige Orbit QD/DT
Installation Manual
INS483

1 INS483
• ACCTVeventtriggerutilisingtwoindependentpassiveinfrareddetectorscombinedinaT05package
andamicrowavesensor.Bothsensorshavetotriggerbeforethedetectorsignalsanalarm.Thishigh
precision,veryreliablepresencedetectorhasbeendesignedforusewithinCCTVinstallations.
Programmableparametersincludeapulsecountfeatureandachoiceofdetectionrangesfrom10to
30metres.
• Theintegraldualaxistiltsensorallows180˚ofpanand90˚tilt.Thisincreasesthespeedofthe
outdoorinstallationandprovidesincrediblyaccurateaimingofthedetectionpattern.Theelectronics
moduleisacryliccoatedforadditionalcomponentstability.ItisencasedinanABShousingwitha
UVstabilisedtranslucentfrontcoverensuringthesensorisimpervioustoandunaffectedbyweather
conditions.Additionally thecombination ofprecision electronics,digital whitelight lterand double
shieldingeliminatesfalsealarmsfromthesunandothervisiblelightsources.
•ThePrestigeOrbitdesigngivesaneatandprofessionalappearancewithnovisibleindicationofthe
orientationofthedetectorhead,andtotallyhidesthewiring.
Introduction
Quick Installation Guide
Applysupplyvoltagetotheunit,theblueLEDashes3times.
Thedetectortakesapproximately2-3minutestosettle.
ThewalktestLEDisfactorysettoOFF.PressingtheprogrambuttononcewillenablethewalktestLED
for5minutes.
THE FRONT COVER MUST BE FITTED WHEN WALK TESTING.
FACTORYSETTINGSARE:-
1RANGE30METRES
2PULSECOUNT1
3LEDOFF
WhenenabledthePrestige Orbit DT hasthreeLEDindicators.
Green-Microwavedetection
Red-BothPIRsdetection
Blue-Alarmoutput,bothPIRsandmicrowavedetection

INS483 2
Duringinstallationtheelectronicsmustbeprotectedagainstwater,astrappedmoisturecanaffector
damagetheunit.
1
2 3
1) Using the template provided drill the wall to
acceptthetwoxingscrews,thecableentryand
thetampercup(ifused).See fig. 1 and 2.
Note: We recommend using the tamper cup on
uneven wall surfaces.
2)Removethecoverassemblybylooseningthelockingscrewusingtheallenkeyprovided.Thecover
hingesfromthetopandliftsoutofthelocationslot.See fig. 3.
1. Mounting the Unit
43) Feed standard 8 core alarm cable into the
cable entry; bare the wires and connect to
theremovableterminalblockasshownin fig.
7.Screwtheunit to thewallensuringthat the
tamper pin is correctly located and that the
tamper microswitch is closed. See fig. 4 and
5.Toaidinstallation,twosparetamperfeetare
provided.Oneis1mmlonger andtheother is
2mm longer than the tamper foot originally
tted.Thetamperfootisapushtandcanbe
removedbycarefullypullingitfromthepin.See
fig. 2.
Template
OptionalforTamperCup
CableHoles
Tamper
Foot
FixingHoles
TamperCup
Tamper
Cup

3 INS483
2. Connecting the Unit
7Tamper Connection
Route1
Alternative
Route2
Route3
NotRecommended
NormallyClosed
TamperCircuitFront&Rear
AlarmOutput2
Multiplexer,PTZDome,
DVR,etc.
AlarmOutput1
Multiplexer,PTZDome,
DVR,etc.
0VSupply
12VDCSupply
5 6
4)AlwaysensurewhenreplacingtheelectronicsmodulethattheLEDisfacingforwardsoastoensure
correctalignmentofthebeampattern.(Refertosectiontitled“MultibeamAlignment&Masking”)
5) When the detector has been aligned to suit the installation, replace the front cover and lock as
shown.See fig. 6.
N/Closed
N/Open
Alarm Connection

INS483 4
ThemultifunctionlensttedtothePrestigeOrbitdetectorproduces7longrangebeamsand7medium
toshortrangecurtainbeams.Movementacrossthebeamsproducesthebestresponseandrange,
whilstmovementtowardsthedetectorwillbelessresponsive.Theunitdetectsthechangesinheatand
movementinthebeampattern,thereforeitemssuchastrees,shrubs,ponds,boileruesandanimals
shouldbeconsideredwhenpositioningthedetector.
Thedetectormoduleisttedwithtwoslidingshutterstoreducethedetectionangle.Anadditionalset
ofcurtainsisprovidedshouldthebeampatternneedtobenarrowedevenfurther,e.g.iftheminimum
detectionangleof10degreesisrequired.
Thecurtainsarettedto thepanand tiltmoduleasindicatedin fig. 8 below.Eachsection ofthe
detector’slensgivesacoveragepatternofapproximately10degrees.See fig. 8.
3. Multibeam Alignment & Masking
8
9

When mounting higher than boundary fences rotate the module and mask off any beams, either
verticallyorhorizontally,thatfalloutsidetheareabeingcovered.
Useportionsoftheself-adhesivesilvermasksuppliedtotherear,smoothside,ofthelensasshownin
thediagramsbelow.Alwaysreplacethelensthecorrectwayuptoensureexactbeampatterncoverage
(thetopoftheFresnellensismarked-TOP).See fig. 9. (Page 4)
3. Multibeam Alignment & Masking
*Prestige Orbit DT only
*
5INS483

INS483 6
The user can individually program a number of congurable
settingsasillustratedintheprogrammingchart.Factorysettings
areshownasshadedboxes.
Changes to the existing settings can easily be made. To reset
the factory settings simply remove power form the detector,
pressandholdtheprogram button (fig. 10) whilst temporarily
applyingpowertothedetector:eitherbeforeinstallation,witha
PP3battery,orbyapplying12Voltstotheunitonsite.
4. Programming
10
123
1RANGEMETERS 10 20 30
2 PULSECOUNT 12
3LED OFF ON
SETTING
OPTIONS
TochangeanyofthePrestigeOrbitsettings:-
1)Presstheprogrambuttonasshowning.10forthenumberoftheOptiontobechangedi.e.once
forrange,twiceforpulsecount,threetimesforLED.
2)WaitfoursecondsuntiltheblueLEDindicatorgoesoff.
3)Theindicatorwillthenashouttheexistingsetting.
4)Tochangethesettingforthatoption,immediately(within2seconds)pressthebuttonthenumberof
timesrequiredforthenewsetting.
5)Theindicatorblinkstwiceandthechangesarestored.
AnyalterationsmadetothePrestigeOrbitsettingsarestoredinthedetector’snonvolatilememory.
EXAMPLE
TochangetheLEDSettingfromOFFtoON.
1)Presstheprogrambuttonthreetimesandreleasethebutton.
2)Waituntiltheindicatorgoesoff.
3)Theindicatorwillnowashonce.
4)Presstheprogrambuttontwiceandreleasethebutton.
5)Theindicator ashes twiceshowingthat the optionhasbeen stored andthedetector returns to
normaloperation.
Program
Button
LED
PROGRAMMING CHART

5. Walk Test
Therangeofthedetectorincreaseswithoutthefrontprotectivecover.Thereforethefrontcovermustbe
ttedtoestablishthecorrectbeampatternalignmentandwhentestingtheoutputs.Usetheprogram
tableonpage5toadjusttherangeasnecessaryandpanandtiltthelensmoduleovertheeldofview
toobtainthecorrectcoveragearea.
When the ‘program’ button is pressed momentarily the blue indicator lights and pulse count ‘1’ is
automaticallyselected.Theunitcanthenbealigned.TheblueindicatorwilllightonthePrestigeOrbit
every time a detection takes place. This test mode will automatically cancel ve minutes after last
detection.Alternatively,removethepowerandthenre-apply.
7INS483
6. Walk Tester
ThePrestigeOrbitWalkTesterisaninstallationtoolthatwillhelptheinstallersetupthedetectoron
site.ConsiderabletimewillbesavedinthesetupprocedurewhenusingtheWalkTester,andit’suse
ishighlyrecommended.Ifyouhavedifcultyinaligningthedetector,andyouhaveissueswitheither
shortorlongranging,aWalkTesterwillassistgreatlyincorrectalignmentandperformance.
EachPrestigeOrbithasbeenttedwithandinfra-redLEDemitter.Whenactivationoccursthetransmitter
sendsasignal.ThissignalisthenreceivedbytheWalkTesterandaverybrightwhiteLEDontheWalk
Testerashes,alsoapiezospeakersounds.
UndernormalsituationsboththeLEDandthesoundercanbeseenandheardupto50meters.
LED
Sounder
11
WalkTester
PrestigeOrbitPCB WalkTesterHolder
BlueLED
TheWalkTestercomeswithamountingbracket/holder.
FirsttaPP3batteryintotheWalkTesterbatterycompartment.
Thisisdonebyremovingthebatterycompartmentcover.Please
ensure that the on/off switch on the Walk Tester is set to the
‘off’positionwhileconnectingthebattery.Whenttedclosethe
batterycompartmentandtheWalkTesterisreadyforuse.
RemovingtheBatteryCover

8. Option Definitions
PULSE COUNT
Thisisthenumberoftimestheunithastodetectonbothofitssensorsbeforesignallinganoutput.
LED MONITOR
LEDOff-LEDdisabled.
LEDOn-LEDsignalsadetection.
N/OPEN & N/CLOSED
Thesearemagneticallyimmunevoltfree relay contacts used to triggeralarminputsonconnected
equipment.Thecontactsareratedatamaximumof24VAC/DC@50mA.
ACCESSORIES
Texecomisabletosupplythefollowingaccessoriestoaidinstallations:
Polemountbracketavailableonrequest.
(JAH-0001)PrestigeOrbitWalkTester.
INS483 8
7. Using the Walk Tester
Remove the cover from the Prestige Orbit housing by
looseningthelockingscrewatthebottomofthedetector.
Thiswillallow accesstothe programmingbuttonshown
inFig.11(andtoalsotoshowthelocationoftheblueIR
emittingLED).
PlacethePrestigeOrbitinto‘walktest’modebypressing
theprogrammebuttononce(Fig.11).ThePrestigeOrbit’s
clearLEDwillthenashoutits current settings. Waitfor
theashingsequencetonish.ThePrestigeOrbitisnow
in walk test mode and will remain in that state for ve
minutesafterthelastdetection,whereafteritwillrevertto
normalmode.Thewalktestcanbecancelledatanytimeby
pressingtheprogrammebuttontwice.
ReplacethePrestigeOrbitcoverandplacetheWalkTesterinthemetalholder.
SlightlyloosenthestainlesssteelscrewonthebottomofthePrestigeOrbit,just
enoughso thatthedrilledtabontheWalkTesterbracketcanslidearoundthe
screwthread.ThengentlytightenthescrewtoholdtheWalkTesterandholderin
place.TurntheWalkTesteron.
The Walk Tester will illuminate and sound every time the Prestige Orbit is
activated.
Whennishedtesting,turnofftheWalkTesterandremoveitandtheholderfrom
thePrestigeOrbit.TightenthescrewonthebaseofthePrestigeOrbit.Theexternal
detectorisnowready.

9INS483
9. Approved External Microwave Frequencies - Prestige Orbit DT
9.35GHz 9.90GHz 10.525GHz 10.587GHz
Albania •
Argentina •
Australia •
Austria •
Belgium •
Brazil •
Croatia •
Czech Republic •
Denmark •
France •
Germany •
Greece •
Holland •
Hungary •
Iceland •
Indonesia •
Italy •
Latvia •
Lithuania •
Malta •
Norway •
Portugal •
Poland •
Russia •
Slovakia •
South Africa •
Spain •
Taiwan •
Thailand •
U.A.E •
UK •
Ukraine •
USA •