Texecom PREMIER 640 User manual

Issue 1
Premier 640
Installation Manual

Contents Premier 640 Installation Manual
2 INS344
Contents
1. New Features....................................................... 4
Area Profiles ............................................................. 4
User Profiles ............................................................. 4
Access Profiles......................................................... 4
User Programming ................................................... 4
Default Settings ........................................................ 4
Mandatory Log.......................................................... 4
Alternative Wiring Configurations............................ 4
Additional Radio Devices......................................... 4
2. System Overview ................................................ 5
System Architecture ................................................. 5
Control Panel............................................................ 5
Remote Keypads ...................................................... 6
Zone Expanders........................................................ 6
Output Expanders..................................................... 6
Communicators ........................................................ 6
Other Devices ........................................................... 7
3. Installation ........................................................... 8
Installation Sequence............................................... 8
Control Panel............................................................ 8
Power Supply Ratings............................................ 12
Connecting AC Mains............................................. 12
Connecting Batteries.............................................. 12
Connecting Devices to the Network ...................... 13
Remote Keypads .................................................... 15
8XP Zone Expander ................................................ 16
4 XP Zone Expander ............................................... 17
iProx Module........................................................... 17
60IXD Zone Expander ............................................. 18
OP16 Output Expander........................................... 19
Zone and Output Numbering ................................. 20
Zone Connections .................................................. 21
Auxiliary Tamper Connections............................... 22
Speaker Connections ............................................. 22
External Sounder Connections .............................. 22
Panel Outputs 1 - 5................................................. 23
Digicom Outputs 1 - 8............................................. 23
2-Wire Smoke Detector .......................................... 24
Expander Auxiliary Input ........................................ 24
Plug-on Communicators ........................................ 25
RP9 Radio-Pad........................................................ 26
GSM Module ........................................................... 26
AV Module............................................................... 26
ComIP Module........................................................ 26
PC-Com................................................................... 27
UNI-Com ................................................................. 27
PRINT-Com ............................................................. 27
RPD-Com ................................................................ 27
GSM-Com................................................................ 27
Connecting a Computer ......................................... 27
Connecting a Printer .............................................. 27
4. Commissioning and Troubleshooting ............. 28
Commissioning....................................................... 28
Trouble-Shooting.................................................... 28
Reset and Service Messages................................. 30
5 Programming the Control Panel ....................... 31
Introduction ............................................................ 31
Factory Defaults ..................................................... 31
Programming Menu Guide..................................... 32
Programming Text .................................................. 33
Copying and Pasting.............................................. 33
Log Off Engineer .................................................... 33
Resetting the Engineers Code (User 00)............... 33
Other Things to Know ............................................ 33
5.1 Zone Setup ...................................................... 34
Zone Types ............................................................. 35
Zone Attributes 1 .................................................... 36
Zone Attributes 2 .................................................... 36
Attributes for Moment or Latch Keys..................... 37
Attributes for Custom Zones.................................. 37
Zone Areas.............................................................. 37
Zone Text ................................................................ 37
Zone Chime ............................................................ 37
Remote Test Enable ............................................... 37
Zone Wiring ............................................................ 38
DD 243 .................................................................... 38
5.2. Area Programming......................................... 39
Timers ..................................................................... 39
Arming Modes ........................................................ 40
Area Arm Suites...................................................... 40
Area Suite Text ....................................................... 41
Suite Arm Modes .................................................... 41
Area Options........................................................... 42
Time Arm Area........................................................ 45
Area Text................................................................. 46
Area Profiles ........................................................... 46
5.3 Global Options ................................................47
System Timers........................................................ 47
System Config. ....................................................... 48
System Options ...................................................... 51
Monitor Hardware................................................... 52
Control Timers........................................................ 52
System Text ............................................................ 53
Part Arm Text.......................................................... 53
Holiday Dates ......................................................... 54
Speaker Tones........................................................ 54
PC Output Text ....................................................... 55
Custom O/P Text .................................................... 55

Contents Premier 640 Installation Manual
INS344 3
5.4 Keypad Setup ..................................................56
Keypad Areas..........................................................57
Keypad Zone Mapping............................................57
Keypad Options ......................................................57
Keypad Speaker Volume ........................................57
Keypad Sounder Options .......................................57
5.5 Expander Setup ...............................................58
Expander Areas.......................................................59
Expander Location Text ..........................................59
Expander Auxiliary Input.........................................59
Expander Speaker Volume .....................................59
Expander Sounder Options ....................................59
5.6 System Outputs...............................................60
Available Outputs....................................................61
Programming Outputs ............................................61
Output Group - Not Used........................................61
Output Group - System ...........................................61
Output Group - Area................................................63
Output Group - Zone...............................................65
Output Group - User Code Entered........................65
Output Group - Control Timer ................................65
Output Group - PC Control.....................................65
Output Group - Door Control..................................65
Output Attributes.....................................................66
X-10 Outputs............................................................66
Custom Outputs ......................................................66
5.7 UDL/Digi Options.............................................67
Reset Digi ................................................................67
Start Test Call..........................................................67
MSN/Pre-Dial No. ....................................................67
Program Digi ...........................................................68
Digi Options ............................................................71
Area Accounts.........................................................71
UDL Options............................................................72
Radio/SMS Options.................................................74
Com Port Setup.......................................................76
Zone Alarm Reporting Codes .................................78
5.8 Setup Users .....................................................84
Add/Edit Users ........................................................84
Programming New Users........................................85
User Name Text.......................................................85
Deleting Users.........................................................85
User Profiles............................................................86
User Profile Text......................................................87
User Options ...........................................................87
User Options 1 ........................................................87
User Options 2 ........................................................87
User Options 3. .......................................................87
User Options 4 ........................................................88
User Time Lock .......................................................88
Predefined User Profiles.........................................88
User Functions and Options For Predefined User
Profiles ....................................................................89
Access Profiles .......................................................90
5.9 Engineer Utilities.............................................91
View Event Log........................................................91
Do Bell Test............................................................. 94
Do Walk Test ...........................................................94
View Zone Status ....................................................95
Do System Tests .....................................................95
Confirm Devices .....................................................96
View RKP Status .....................................................96
View Exp. Status .....................................................96
Set System Time .....................................................97
Set System Date......................................................97
Change Eng. Code..................................................97
Adjust Volumes .......................................................97
Default NVM Data....................................................98
Location Text........................................................... 98
Print Log Data .........................................................98
Soak Test Areas......................................................98
View iD Data ............................................................ 99
Configure Radio...................................................... 99
5.10 Programming Part Arms.............................100
Alter Part Arms...................................................... 100
6. Specifications..................................................101
Control Panel ........................................................101
Remote Keypads...................................................102
Zone Expanders .................................................... 102
Output Expanders ................................................. 103
Standards..............................................................103
Warranty ................................................................ 103
EN50131 Markings................................................ 103
Declaration of Conformity ....................................104

System Overview Premier 640 Installation Manual
4 INS344
1. New Features
With Version 8 Software, the capacity of the Premier 640
has been significantly enhanced.
The new panel can accommodate up to 500 users and 64
areas.
In order to manage the additional capacity, some changes
to the programming have been made which are briefly
described in this section.
Area Profiles
Area profiles are used to group areas together into suites
this is a useful way to identify any number of areas which
belong to a single entity such as a company or floor in a
multi-occupancy building.
80 Area profiles are provided each of which can be
programmed with any combination of 64 areas.
Each area profile can be named to relate it to the installation.
Each zone is then allocated to an area profile in the same
way as they were previously assigned to an area.
Area profiles can also be allocated to users, keypads and
expanders in the same way as was previously done with
areas.
User Profiles
The panel provides 32 user profiles for managing the
functions and features available to different types of users.
There are a number of predefined user profiles by default
which may well satisfy all the requirements of an installation.
Two profiles, Engineer and Master are required to have
particular features and are not editable, the remaining 30
can be customized by the Engineer or Various users
depending on the specific settings.
A user profile defines the functions and features available to
a particular type of user.
Once a user profile has been defined it can be allocated to
any number of individual users.
This approach simplifies the programming of users in a large
system as the profile only has to be set up once, then it is a
simple matter for the profile to be applied to a particular
group of users.
Using user profiles has the advantage that any changes can
be applied to the profile once and they will automatically be
applied to any user allocated to the profile.
Access Profiles
One of the functions provided by Texecom Alarm Panels is
door control, allowing electronic door locks to be activated
by designated outputs on keypads or proximity units.
The 640 provides 99 access profiles, each defining how
access is granted to any combination of up to 64 door
controls.
Access profiles are programmed and allocated in a similar
way to user profiles, but are allocated to individual users
independently of the user profile.
User Programming
To program a user it is necessary first to program the user,
area and access profiles.
Set up the user and program a user code, then allocate the
appropriate profiles.
If at some later stage it is necessary to make changes, either
change the appropriate profile, (which will effect all users
allocated to the profile) allocate different profile which
matches the new requirement or program a new profile and
allocate it to the user.
Each user can have any combination of user, area and
access profiles.
Default Settings
All users are assigned to Area Profile 80 (All System Areas).
Users are also set to ‘No Door Access’ by default.
Area Profiles 1-64 are each assigned to an individual area,
(Profile 01 to area A1, Profile 02 to area A2 and so on to
Profile 64 assigned to area H8.
Area Profile 00 is defaulted as no areas and Profile 80 is all
areas.
All zones are assigned to Area Profile 1 (Area A1).
Access Profiles 1 -64 are each assigned to an individual
door (Profile 01 to Network 1 Door 1, Profile 02 to Network 1
Door 2 and so on to Profile 64, assigned to Network 8 Door
8).
Mandatory Log
The component requirements for control equipment
TS50131-3 requires that mandatory log events are not
overwritten by non-mandatory events.
To satisfy this requirement an additional 500 mandatory
event log has been created which records only the
mandatory events.
Operation of the standard system log has not been changed
and mandatory events will be duplicated in the standard log.
The standard log has been extended to 5000 events.
Alternative Wiring Configurations
4 new EOL zone wiring options have been provided to allow
compatibility with other manufacturers products and to allow
the use of alternative anti-masking detection devices.
Normally open & normally closed contacts are catered for,
this is primarily for key switches
A warning device monitoring circuit type has been provided
to support remote testing of sounders.
Additional Radio Devices
The number of RadioPlus intelegent radio devices that can
be learnt to the system has been increased from 32 to 100.
This is mainly to accommodate the additional users and
allow more radio FOBs.

Premier 640 Installation Manual System Overview
INS344 5
2. System Overview
System Architecture
8 Programmable
100mA Outputs
(Digi Outputs)
Bell Tamper Input
Auxiliary Tamper Input
5 Programmable
A & 1 Relay)
Outputs
(4 x 500m
Control
Panel
Premier LCD/LCDP
Premier LCDL/LCDLP
4 Wire Data Network 1
16 Programmable
100mA Outputs
64 Keypads
(Up to 8 per network)
Premier OP16
32 Output Modules
(Up to 4 per network)
Alarm Receiving
Centre
Modem
PC and Modem for
Remote Upload/Download
PC-Com
PC and for
Local Upload/Download
PC-Com
Plug on Digimodem
Plug on
(Com300, Com2400
or ComISDN)
Radio-Pad,
GSM Module
2 Zone
Inputs
1Programmable
100mA Output
2 Zone
Inputs
1Programmable
100mA Output
Speaker
Output
4 Wire Data Network 2-8
Speaker Output
8 Zone Inputs
Auxiliary Input
Premier 8XP
8 Programmable
100mA Outputs
64 Expanders
(Up to 8 per network)
Wire as Network 1
2 to 640 Zones
Via Expanders & Keypads
Bell/Strobe Outputs
Power
NetworkNo
Address
Zones
Power
NetworkNo
Address
Zones
Power
Info.
Ready
Service
Omit
Area
Yes
Part
Chime
Omit Reset
Menu
2 abc
No
13
def
6 mno
9 wxyz
5 jkl
8 tuv
0
4
ghi
7 pqrs
640
7
Power
Info.
Ready
Service
Omit
Area
Yes
Part
Chime
Omit Reset
Menu
2 abc
No
13
def
6 mno
9 wxyz
5 jkl
8 tuv
0
4
ghi
7 pqrs
640
7
Control Panel
•Expandable to 640 zones via keypads and zone expanders
•8 x 4-wire data network (standard 7/0.2 alarm cable)
•Up to 64 keypads and 64 zone expanders (8 per network)
•Up to 32 output modules (4 per network)
•64 independent areas each with 3 part arms
•500 programmable User codes
•5000 Event Log (time & date stamped)
•500 Event Mandatory Log (time & date stamped).
•32 Event Alarm Log (time & date stamped).
•5 programmable panel outputs (4 x 1A & 3A relay)
•2.0 Amp power supply
•8 programmable digicom outputs (100mA each)
•32 character zone text
•Facility for Plug-on Digimodem (Com300/2400/ComISDN)
•Facility for Plug-on Paknet RP9 Radio-Pad
•Facility for Plug-on GSM Module
•Facility for Plug-on IP Module (ComIP/Chiron/WebWayOne)
•Facility for a plug-on RedCARE/RM8 Relay Module
•Facility for a plug on Engineers Keypad.
•PC-Com/printer port

System Overview Premier 640 Installation Manual
6 INS344
Remote Keypads
Premier LCD
•32 character text display
•2 fully programmable DP or EOL zones
•1 fully programmable output (100mA -ve applied)
•Fully adjustable back-lighting, normally bright, dim or off,
changing to bright during entry or following a key press
•Built in piezo sounder
•Programmable ‘Info.’ LED
Premier LCDL
ALL the features of the Premier LCD plus:
•Larger 32 character text display
•Speaker output
Premier LCDP
•Premier LCD with a built in Proximity Tag Reader
Premier LCDLP
•Premier LCDL with a built in Proximity Tag Reader
Zone Expanders
Premier 4XP
•4 fully programmable DP or EOL zones
•2 fully programmable outputs (100mA -ve applied each)
•Remotely wired
Premier 8XP
•8 fully programmable DP or EOL zones
•8 fully programmable outputs (100mA -ve applied each)
•Speaker output
•Programmable auxiliary input
•Remotely wired
Premier PSU200XP
•Monitored Power Supply with integral Premier 8XP
Premier 60iXD
•2 loops x 30 fully programmable iD zones
•iD biscuit technology
•Plug-on
“iD” is a registered trade mark of Chloride Safety System Limited
RadioPlus Intelligent Receiver
•Plug – 0n receiver for Texecom RadioPlus devices.
•Accepts 32 Devices
RadioPlus Network Receiver
•Network version of the Intelligent Radio Reciever..
Output Expanders
Premier OP16
•16 fully programmable outputs (100mA each)
•1 fault output (100mA -ve applied)
•Can be connected to mimic panels to give zone indication
•Can be connected to relays and sounders
Premier RM8 Relay Module
•Plug-on relay card (RedCARE footprint)
•8 separate inputs for stand alone operation
•8 x 3Amp relay outputs (n/o, n/c, com)
•Output ‘ON’ LED indication
Communicators
Com300
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager protocols
•300-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
•For use with an analogue telephone line (REN = 1)
Com2400
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager and SMS
Messaging protocols
•2400-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
•Sends SMS text messages to mobile phones
•For use with an analogue telephone line (REN = 1)
ComISDN
•Multi-protocol communicator supporting Fast Format,
Contact ID, SIA Level II and EasyCom Pager protocols
•300-baud (analogue) or 19200-baud (digital) Modem for
remote uploading and downloading using the Wintex
UDL software and a PC
•For use with an ISDN telephone line
ComIP
•Multi-protocol communicator supporting Fast Format,
Contact ID and SIA Level II protocols via TCP/IP
•High speed modem for remote uploading and
downloading using the Wintex UDL software and a PC
•For use with ADSL/DSL/Broadband/WAN/LAN etc.
RP9 Radio-Pad
•Paknet radio communicator supporting Fast Format and
Contact ID protocols
•4800-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC
GSM Module
•Provides a GSM telephone path for Premier Digital
Communicators
•Sends SMS text messages to mobile phones
•Arm, Disarm, Reset the alarm, turn outputs on and off,
omit zones and send messages to the control panel
using SMS text messages
•9600-baud modem for remote uploading and
downloading using the Wintex UDL software and a PC

Premier 640 Installation Manual System Overview
INS344 7
Other Devices
PremieriProx
•Provides an alternative to Prox keypads for setting &
unsetting with a proximity FOB.
•Remote Prox readers available for external or internal
use.
•Interfaces with 26 bit Wiegand devices.
•Can be used as standalone door entry control
PC-Com
•For connecting a PC to the control panel via an RS232
Serial port allowing local uploading and downloading using
Wintex UDL software
USB-Com
•For connecting a PC to the control panel via a USB 1.0 or
2.0 port allowing local uploading and downloading using
Wintex UDL software
UNI-Com
•For connecting a serial device i.e. PC modem or mobile
phone to the control panel
PRINT-Com
•For connecting a serial printer to the control panel
RPD-Com
•For connecting a RP9 Radio-Pad to the control panel
GSM-Com
•For connecting a GSM Module to the control panel
Premier X10-Com
•For controlling X10 enabled devices on the ring main.
Premier Battery Splitter
•Allows two backup batteries to be connected to a single
set of battery terminals, and will provide appropriate
monitoring and charging for each.
External Sounders
•Texecom supply a range of external sounders

Installation Premier 640 Installation Manual
8 INS344
3. Installation
Installation Sequence
Before attempting to install the alarm system, read this
section. Once you have an overall understanding of the
installation sequence, carefully work through each step.
1: Design the Layout
Make a rough sketch of the premises to get an idea of where
the alarm detection devices, keypads, zone expanders etc.
are to be located.
2: Mounting the Panel
The control panel should be mounted in a dry area close to
an unswitched AC power source and the incoming telephone
line (if using a communicator).
!You must complete all wiring before connecting the
battery or applying AC mains to the control panel.
3: Install the Keypads and Zone Expanders
Mount and connect the keypads, zone expanders and output
modules to the control panel (see page 13 for wiring details).
4: Install the Alarm Detection Devices
Install the detection devices, PIR’s, Contacts, PA Buttons etc.
and connect them to the control panel (see page 21 for wiring
details).
5: Install the External Sounder
Install the external sounder and connect to the control panel
(see page 22 for wiring details).
6: Other Wiring
Complete all other wiring including speakers, telephone line
and output connections etc. (see pages 22 - 23 for details).
7: Applying Power to the Control Panel
Once steps 1 to 6 are completed, power can be applied to
the control panel.
When applying power for the first time, the factory default
settings must be loaded (see page 28 for details). Power
should always be connected in the following order:
•Connect the red battery lead to the positive terminal of
the battery and then connect the black battery lead to the
negative terminal
!The panel will only become ‘live’ when the AC
Mains is connected or the ‘Battery Kick-start’
button is pressed.
•Connect the AC mains
8: Programming the Control Panel
Please refer to section 5 for instruction on programming the
control panel.
9: Testing the System
Test the system thoroughly to ensure that all features and
functions operate as required (see page 91 for details).
Control Panel
Mounting
Mount the control panel on a flat, plumb wall using at least
three screws of appropriate size.
!It is essential to ensure that none of the fixing slots or
cable entries are accessible after fixing.
Mains cabling must be secured (e.g. with a cable tie) to
one of the anchor points provided.
Wiring the Control Panel
WARNING: ELECTRICITY CAN KILL
BEFORE connecting the control panel ALWAYS
disconnect the supply at the consumer unit.
If in ANY doubt consult a qualified electrician.
"IMPORTANT SAFETY INFORMATION. HAZARDOUS
VOLTAGES INSIDE, NO USER SERVICEABLE PARTS,
NO USER ACCESS.
!ONLY connect the mains supply to the mains terminal
block, NEVER connect the mains supply directly to the
PCB.
ALWAYS refer to National Wiring Regulations when
conducting installation.
An appropriate and readily accessible disconnection
device (e.g. an unswitched fused spur) MUST be
provided as part of the installation.
The disconnection device must NOT be fitted in a
flexible cord.
Where identification of the neutral in the mains supply
is NOT possible a two-pole disconnection device
MUST be used.
The building mains supply MUST incorporate
appropriate short-circuit backup protection (e.g. a fuse
or circuit breaker) of High Breaking Capacity (HBC, at
least 1500A).
Use mains cable of adequate carrying capacity for the
rated current (i.e. at least 0.75mm2).

Premier 640 Installation Manual Installation
INS344 9
Control Panel Layout
2
79
Com 2
Com 1
Expansion
Load
Defaults
Engineer
Remote
Kick
Start
OP1-
Tamp
OP5
N/O COM N/C
+12v
Bell
Strb
0v
OP2-
OP3+
OP4+
Box
Tamp
BATT
A.C.
DC+
L/M
R/R
DC
-
2
3
5
6
7
8
4
1
DIGICOM OUTPUTS
+
-
V
100mA = 1 Amp
Heartbeat
Aux
Tamp
Aux 12v
-
+
Spk+
Spk
-
NETWORK 2NETWORK 1
+ -T R + -T R
NETWORK 3
+ -T R
NETWORK 4
+ -T R
NETWORK 5
+ -T R
NETWORK 6
+ -T R
NETWORK 7
+ -T R
NETWORK 8
+ -T R
Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault
Com 3
F4
F13
F5
F6 F7 F8 F9 F10 F11 F12
F2
F3
F1
Bell/Spk
Fault
Aux12V
Fault
T
R
T1
R1
Back Tamper Screw
Mains Terminal Block & Fuse
Tamper Switch
Mains Transformer
Control Panel
Circuit Board
Space for
Batteries
Plug-on
Digimodem
Cable Enties
!If back tamper is required, the back tamper screw must be fitted as indicated.

Installation Premier 640 Installation Manual
10 INS344
Control Panel PCB Layout
1: AC Input
Connected to the 16.5V transformer.
DO NOT CONNECT THE MAINS SUPPLY TO THE AC
INPUT TERMINALS ON THE PCB.
2: Battery Connections
A 12V rechargeable battery must be connected to these
terminals in order to provide continuous system operation in
the event of an AC Mains failure (see page 12 for details).
3: Digicom Power & Inputs
These terminals provide unfused power; remote reset and line
fault inputs and are normally used for connecting a stand-alone
communicator to the control panel (see page 23 for details).
4: Digicom Outputs
Outputs 1 to 8 are low current (100mA ‘-ve’ applied) and
would normally be used when connecting a stand-alone
communicator to the control panel (see page 23 for details).
Each output is fully programmable (see page 61 for details).
5: Engineers Keypad
A portable Engineers keypad can be plugged on here to
allow easier access for programming and testing.
!When using a keypad as an Engineers keypad, the
address must be set to ‘10’ (see page 15 for details).
The keypad zones and lid tamper are not monitored.
6: Network Data Connections
Networks provide connection for the keypads and zone
expanders. The ‘+’ and ‘–’ terminals provide power whilst
the ‘T’ transmits data and ‘R’ receives data (see page 13 for
details).
7: Auxiliary 12V Power
These terminals are for connecting devices that require 12V
power (protected by a 1A fuse).
8: External Sounder Connections
These terminals are used for connecting to an external
sounder unit (see page 22 for details).
9: Auxiliary Tamper Connections
These terminals can be used for monitoring the tamper loop of
an auxiliary device (see page 21 for details).
10: Loudspeaker Connections
These terminals can be used for connecting up to one 16Ω
or two 8Ω loudspeakers (see page 22 for details).
11: Panel Outputs
Outputs 1 & 2 are 500mA ‘-ve’ applied, outputs 3 & 4 are
500mA ‘+ve’ applied and output 5 is a clean contact relay
(see page 23 for wiring details). These outputs are all fully
programmable (see page 60 for details).
12: Plug-on Communicator Connections
This socket provides connection for Premier plug-on
communicator (see page 25 for details).
13: Box Tamper Connection
The box tamper micro switch is connected here. The micro
switch provides tamper protection for the main control panel in
case of unauthorised access. To disable the box tamper,
remove the micro switch lead and fit a jumper link across the
two pins.
14: Plug-on RedCARE/Dualcom Connections
These pins provide connections for a plug-on RedCARE,
Dualcom, Digicom or RM8 Relay module. Each output is fully
programmable (see page 61 for details).
!When a device is plugged on to these pins, not all
outputs may be available, please refer to the relevant
documentation for details.
15: Battery Kick-start Button
When powering up the panel without AC Mains present, this
button must be pressed in order to connect the battery.
!If AC Mains is present this button does not need to be
pressed.
Com 2
Com 1
Expansion
Load
Defaults
22
15
12
Engineer
Remote
5
17
14
16
13
Kick
Start
OP1-
Tamp
OP5
N/O COM N/C
+12v
Bell
Strb
0v
10
8
11
OP2-
OP3+
OP4+
6
7
19
18
Box
Ta m p
BATT
A.C.
DC+
L/M
R/R
DC
-
2
3
5
6
7
8
4
1
DIGICOM OUTPUTS
1
3
4
2
+
-
V
1
00mA = 1 Amp
21
Heartbeat
20
Aux
Tamp
9
Aux 12v
-
+
Spk+
Spk
-
NETWORK 2NETWORK 1
+ - T R + - T R
NETWORK 3
+ - T R
NETWORK 4
+ - T R
NETWORK 5
+ - T R
NETWORK 6
+ - T R
NETWORK 7
+ - T R
NETWORK 8
+ - T R
14
Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault Tx RxFault
Com 3
F4
F13
F5
F6 F7 F8 F9 F10 F11 F12
F2
F3
F1
16
Bell/Spk
Fault
Aux12V
Fault

Premier 640 Installation Manual Installation
INS344 11
16: Communication Ports
Com Port 1 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 76 for details).
Com Port 2 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 76 for details).
Com Port 3 is a serial communications port and can be used
for connecting a PC running Wintex or any supported serial
device to the control panel (see page 76 for details).
17: Network Data Indicators
The red LED indicates that data is flowing out of the control
panel and normally flashes very quickly. The green LED
indicates that data is flowing into the control panel and
normally flashes slowly, the green LED flashes faster as more
devices are connected (see page 13 for details).
18: Load Defaults Button
Press and hold this button whilst applying power to the
control panel to load the factory default settings. Press and
hold this button for 7 seconds with power already on the
panel to restore just the Engineer code to the factory setting
of !"#$.
!Loading the factory defaults can take up to 60 seconds
to complete.
Loading defaults will only be possible if the NVM has
not been locked (see page 49 for details).
For a complete list of factory defaults, see the Factory
Defaults and Quick Reference Guide supplied separately
with the control panel.
.
19: Expansion
The Expansion Port can be used for connecting a 60XPiD
Zone Expander (see page 18 for details) or an AV Module
(see page 26 for details).
20: Heartbeat LED/Power Light
Flashes steadily to indicate that the control panel is
functioning correctly. If the light is ON or OFF all the time,
then there could be a problem (see page 28 for details).
21: Current Reading Pads
To calculate the current draw of the control panel, measure
the voltage across the two pads and multiply by 10 i.e.
Reading = 34mV (x10) = 340mV = 340mA.
22: NVM
All system programming data and the system & event logs
are stored in a removable non-volatile memory devices.

Programming the Control Panel Premier 640 Installation Manual
12 INS344
F1 - F5: Protection Fuses
The following electronic fuses are provided:
•F3 (1600 mA) Battery
•F4 (250mA) Speaker
•F5 (900mA) Network 1
•F6 (900mA) Bell/Strobe
•F7 (900mA) Network 2
•F8 (900mA) Network 3
•F9 (900mA) Network 4
•F10 (900mA) Network 5
•F11 (900mA) Network 6
•F12 (900mA) Network 7
•F13 (900mA) Network 8
•F14 (900mA) Auxiliary 12V
Power Supply Ratings
If installing to PD6662, the system standby times in the event
of a mains power failure vary depending on the grade and
how AC fail is signalled:
System Standby Times
Grade 2 Grade 3
AC Fail signalled
as AC Fail
Grade 3
AC Fail signalled
as Fault
12 Hours 12 Hours 24 Hours
The “Rated Power” of the control panel will depend on the
size of the standby battery, standby time and the installation
grade:
7 Ah Standby Battery
Max Power
Available
from control
panel
Grade 2 –
Rating
Grade 3 –
Rating
AC Fail
signalled as
AC Fail
Grade 3 –
Rating
AC Fail
signalled as
Fault
2 A 580mA 580mA 290mA
17 Ah Standby Battery
Max Power
Available
from control
panel
Grade 2 –
Rating
Grade 3 –
Rating
AC Fail
signalled as
AC Fail
Grade 3 –
Rating
AC Fail
signalled as
Fault
2 A 1.25A 1.25A 710mA
When calculating the current consumption of the system you
must include the current taken by the control panel and all
the devices that it powers. If the total current exceeds the
“Rated Output” for the grade you are installing to then an
additional power supply is required.
Connecting AC Mains
The AC Mains supply is connected to a 3 way ‘Euro Type’
fused terminal block, which is fitted with a 125mA or 500mA
fuse.
!All other wiring MUST be carried out before AC mains
is connected to the control panel.
After connecting the AC Mains, fit the mains cover, this
can be found in the spares bag.
L
E
N
To t r a n sf or m e r
Connecting Batteries
If installing to PD6662: 2004 then only One 12V 7Ah battery
or 12V 17Ah battery can be fitted inside the control panel to
provide continued operation in the event of an AC mains
failure, otherwise, two 12V 7Ah batteries can be connected.
!All other wiring MUST be carried out before the battery
is connected to the control panel.
Connect the red battery lead to the positive terminal of the
battery and then connect the black battery lead to the
negative terminal.
!The panel will only become ‘live’ when the AC Mains is
connected or the ‘Battery Kick-start’ button is pressed.
+
-
Battery
12V 7Ah Battery
+
_
+
-
OR
Battery
12V 17Ah Battery
+
_
+
+
-
-
Battery
12V 7Ah Battery
12V 7Ah Battery
+
_
OR
If not installing to PD6662: 2004
!Two batteries can be fitted and still comply with
PD6662:2004 if the Premier Battery Splitter is used.

Premier 640 Installation Manual Installation
INS344 13
Connecting Devices to the Network
Before connecting keypads, zone expanders and output
modules, isolate ALL power from the control panel (AC Mains
& Battery). Do not continue if there is still power present on
the control panel.
!Connecting devices with power still present on the
control panel may damage the device or control panel
and invalidate any warranty.
Keypads, zone expanders and output modules can all be
connected to any of the 8 sets of network terminals located at
the bottom of the control panel and may be connected serially
(daisy chain), in parallel (star) or any combination of the two (see
Figure 1, page 14 for details).
!No more than 8 zone expanders, 8 keypads and 4 output
modules can be connected to each network.
Whenever new devices are connected to the networks, they
must be confirmed onto the system using the ‘Confirm
Devices’ menu option (see page 96 for details).
Wiring the Network
The networks are made up of four terminals incorporating
power and data. To ensure correct operation, all four
terminals on the device must be connected to the
corresponding terminals on the control panel, or previous
device (see Figure 1, page 14 for details). The table below
shows each terminal and its description:
Terminal Description
+ +12V Supply
- 0V Supply
T Transmit Data
R Receive Data
Devices can be connected using 4-core cable. However, it is
recommended that 6 or 8-core cable is used as the spare cores can
be used to ‘Double Up’ on the power connections if needed.
!Standard 7/0.2 alarm cable can be used for most
installations. However, under certain conditions it may
be necessary to use screened cable.
Cable Distances
The maximum recommended distance for devices when
using standard 7/0.2 alarm cable is:
•250m for each branch when using the star (parallel)
configuration
•When using a daisy chain (series) configuration the
maximum distance will depend on the number of devices
connected on the chain. The more devices that are
connected, the shorter the distance to the last device
(this is due to voltage drop in the cable)
Whichever method of wiring configuration is used, ensure
that the voltage between the ‘+’ and ‘–’ terminals at each
device is no lower than 10.0V when the system is running on
the standby battery.
The table below shows maximum cable runs when one
keypad or expander is installed using standard 7/0.2 alarm
cable with various loads:
Configuration Max. Cable Run
1. Keypad + 2 PIR’s @15mA 250m
2. Expander + 2 PIR’s @15mA 250m
3. Expander + 8 PIR’s @15mA 100m
4. As No. 3 + 16ΩSpeaker 30m
Distances of up to 1km can be achieved between the control
panel and a device. However, a power supply must be installed
close to the device to power it locally, this will help to
overcome voltage drop caused by the long cable run.
Overcoming Voltage Drop
There are several ways to overcome voltage drop:
•Use thicker lower resistance cable. Standard 7/0.2 alarm
cable has a resistance of 8Ωper 100m
•Double up on the power connections – this will require
using a 6 or 8-core cable rather than a 4-core cable
•Install a power supply to power the device locally,
remember to common the two negative connections
Installing a Power Supply
When a power supply is installed, the 0V connections on the
power supply must be connected through to 0V on the
control panel and the +12V connection between the control
panel and the device must be disconnected (see Figure 2,
page 14 for details).
Network Diagnostics
Each network has two LED’s to indicate data flow. The red
LED indicates data flowing out of the ‘T’ terminal and the
green LED indicates data flowing into the ‘R’ terminal. The
table below shows each LED status and its meaning:
LED Status ‘T’ Wire OUT ‘T’ Wire IN
Red LED Flashing Normal Normal
Red LED On Panel Fault Cable Short
Red LED Off Panel Fault Panel Fault
LED Status ‘R’ Wire OUT ‘R’ Wire IN
Green LED Flashing Panel Fault Normal
Green LED On Panel Fault Cable Short
Green LED Off Normal No Data From Devices
!The LED’s are provided as an aid for fault finding and
therefore should not be completely relied upon to
indicate that there is a fault.

Programming the Control Panel Premier 640 Installation Manual
14 INS344
Control Panel
Network 1 to 8
Premier
Keypad
+
TR
-
Network
Premier
Keypad
250 m
Premier
Zone Expander
+
TR
-
Network
+
TR
-
Network
+
TR
-
NETWORK IN
+
TR
-
NETWORK OUT
Premier
Output Module
+
TR
-
Network
Premier
Keypad
+
TR
-
Network
To additional
Keypads, Zone
Expanders or
Output Modules
Figure 1: Network Connections (250m without additional power supply).
250 m
Power
Supply
Disconnect
+12V from
control panel
+-
1 km
Control Panel
Network 1 to 8
+
TR
-
Network
+
TR
-
Network
+
TR
-
Network
+
TR
-
NETWORK IN
+
TR
-
NETWORK OUT
+TR
-
Network
+
TR
-
Network
To additional
Keypads, Zone
Expanders or
Output Modules
Premier
Keypad
Premier
Keypad
Premier
Zone Expander
Premier
Output Module
Premier
Keypad
Figure 2: Network Connections (1km with additional power supply).

Premier 640 Installation Manual Installation
INS344 15
Remote Keypads
Keypad Layout
Zone 2
TA
Zone 1
T
A
NETWORK
+
TR
-
O/P
Address
Switch
Output
Network
Terminals
Tamper
Switch Speaker
Output
Zones
Piezo
Sounder
2431
On
SPK
Connecting Keypads
Keypads are connected to the network terminals located at
the bottom of the control panel (see pages 13 & 14 for
details).
Keypad Addressing
Each keypad must be assigned a different address using the
DIL switches located on the left hand side of the PCB. The
table below shows the keypad addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3 Off Off On Off 2 431
4 Off Off Off On 2 431
5 On Off Off On 2 431
6 Off On Off On 2 431
7 Off Off On On
2 431
8 On Off On On
2 431
Engineers On On On On
2 431
!Never set two keypads on the same network to the
same address.
When using a keypad as an Engineer’s keypad, the
DIL switches must all be ‘On’.
Keypad Zones
The keypad has two programmable zones (see page 21 for
details). Each zone is also fully programmable (see page 34
for details).
Keypad Output
The remote keypad has one programmable output, which
can be used to drive auxiliary devices such as LED’s,
sounders or relays etc. Wire as per Panel Outputs shown on
page 23 (see page 60 for details). The electrical
characteristics for the output are shown below:
Output Max Current Type
1 100mA Switched -ve
Keypad Speaker Output (LCDL/LCDLP Only)
The Premier LCDL and Premier LCDLP keypads have an
output that can be used for driving up to one 16Ωor two 8Ω
loudspeakers (see page 22 for details).
!The speaker volume is also fully adjustable (see page
57 for details).
Programmable ‘Info.’ LED
The ‘Info.’ LED on the front of the keypad can be
programmed to mimic the keypad output or show the armed
status of an area (see page 57 for details).
Adjustable Backlighting
To adjust the keypad backlighting press the YES key for 5
seconds, then with the YES key still pressed use %to
increase or decrease the backlighting until the required
brightness is achieved, then release both keys.
!The backlight can only be adjusted when the keypad is
not in a menu.
Keypad Lid Tamper
The lid tamper of each keypad can be disabled if required
using the relevant keypad option in the Keypad Setup menu
(see page 57 for details).

Programming the Control Panel Premier 640 Installation Manual
16 INS344
8XP Zone Expander
Expander Layout
Zones
5 & 6
Power LED
Tamper
Switch
Engineers
Keypad
Interface
Network
Terminals
Aux
12V
Aux
12V
Zones
7 & 8
Zones
1 & 2
Zones
3 & 4
Outputs
1 to 8
Speaker
Output
Aux
Input
Com Port
123
OUTPUTS
45678
Zone 6 Zone 5
Aux 12v
-
Zone 8 Zone 7
T
AT
AT
AT
A
NETWORK IN
+-TR +-TR
NETWORK OUT
Remote
Power
Zone 2Zone 1
TA
Aux 12v
-
+
Zone 4Zone 3
TATATA
Aux
Input
-
Spk
-
+
1
ON
2 3 4
PSU
DS
YPE0123456
Tamper
Disable
Address
Switch
Connecting Expanders
Expanders are connected to the network terminals located at
the bottom of the control panel (see pages 13 & 14 for
details).
Expander Addressing
Each Expander must be assigned a different address using
the DIL switches located in the centre of the PCB. The table
below shows the expander addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3 Off Off On Off 2 431
4 Off Off Off On 2 431
5 On Off Off On 2 431
6 Off On Off On 2 431
7 Off Off On On
2 431
8 On Off On On
2 431
!Never set two expanders on the same network to the
same address.
Expander Zones
The expander has eight programmable zones (see page 21
for wiring details). Each zone is also fully programmable (see
page 34 for details).
Zone Numbering
The table below shows the zone allocation when the
expanders are installed:
Address Zones
(Network 1)
Zones
(Network 2)
1 9 - 16 73 - 80
2 17 - 24 81 - 88
3 25 - 32 89 - 96
4 33 - 40 97 - 104
5 41 - 48 105 - 112
6 49 - 56 113 - 120
7 57 - 64 121 - 128
8 65 - 72 129 - 136
Expander Auxiliary Input
The expander has one programmable input. This auxiliary input
can be used to monitor auxiliary devices such as tamper loops
etc. Wire as per Aux Tamper shown on page 22 (see page 59
for details). The system will respond as follows:
Input Status System Response
0V Applied Input Secure
0V Removed Input Active
EOL Various *
!For further details on how the input status affects the
system please refer to page 59.
* For wiring details, see page 24.
Expander Outputs
The zone expander has eight programmable outputs, which
can be used to drive auxiliary devices such as LED’s,
sounders or relays etc. Wire as per Panel Outputs shown on
page 23 (see page 60 for details). The electrical
characteristics for the outputs are shown below:
Outputs Max Current Type
1 to 8 100mA Switched -ve
Expander Speaker Output
The expander has an output that can be used for driving up to
one 16Ωor two 8Ωloudspeakers (see page 22 for details).
Expander Com Port
The Com Port can be used to connect a PSU200 montored
power supply or a RadioPlus Inteligent Receiver.
Expander Lid Tamper
The lid tamper of each expander can be disabled if required
by fitting a jumper link across the centre and right hand pins
of the ‘Enable Tamper’ pins (JP2) leaving the left hand pin
free. These pins are located to the left of the address DIL
switch just beneath the fuse.

Premier 640 Installation Manual Installation
INS344 17
4 XP Zone Expander
Expander Layout
NETWORK IN
+-TR +-TR
NETWORK OUT
JP1
Zone
2
Zone
1
TA
Aux 12v
-
+
Zone 4Zone 3
TATATA
1
ON
2 3 4
O/P O/P SPK+ SPK-
2- 1-
Engineers Keypad
JP4
DS
JP2
Network IN
Terminals
Network OUT
Terminals
Outputs 1&2 Loud Speaker Terminals
Tamper Switch
Power LED
Address Switch
Zones
1 & 2
Zones
1 & 2
Aux 12V
Engineers Keypad
Interface
Com Port
Connecting Expanders
Expanders are connected to the network terminals located at
the bottom of the control panel (see pages 13 & 14 for
details).
Addressing
4XP expanders are addressed as one or (normally) two
keypads on the network. Each 4XP has to have a unique
address, which must not conflict with any keypad or any
other 4XP on the same network.
The following table shows the expander addresses & the
keypad slots that each would occupy.
Address DIL 1 DIL 2 DIL 3 DIL 4 Keypads
1 On off off off 1 & 2
2 off On off off 2 & 3
3 off off On off 3 & 4
4 off off off On 4 & 5
5 On off off On 5 & 6
6 off On off On 6 & 7
7 off off On On 7 & 8
8 On off On On 8
Zones
The 4XP provides 4 alarm zones, 2 for each of the 2 keypad
slots it occupies. Each zone is fully programmable (see page
5.1 Zone Setup34) and has to be mapped to the system (see
Keypad Zone Mapping page 57).
Outputs
2 Programmable outputs are provided 1 for each of the 2
keypad slots occupied by the expander (see page 60 for
output programming)
Expander Speaker Output
One speaker output is provided for connecting one external
16Ωor 2 8Ωloudspeakers (see page 22 for details).
The speaker volume is programmed through the keypad setup
menu (see page 57)
!The speaker is available on keypad 1 of the two
keypad slots the 4XP occupies. (ie if the 4XP address is
5, the speaker will programmed as belonging to
keypad 5).
Expander Com Port
The Com Port can be used to connect a RadioPlus
Inteligent Receiver.
iProx Module
iProx Layout
PIP0123456
Options
1
ON
2 3 4
1
ON
2 3 4
Address
RTE
N/C
N/O
Com
+
T
R
Spk
+
D0
D1
SW1 SW2
Internal
Sounder
Off
JP1
Ext
Int
Ext
Int
JP4
JP5
C1
L1-
C2
L2-
L+
Com1
Tamper
Option & Address Switches
Extension
Loudspeaker
Terminals
Wiegand
Interface
Connections
Network
Terminals
For Future Use
Remote
Prox Coil
Connections
Door Strike
Relay
Request to
Exit Input
Volume Adjustment
For Speaker
Connection
The iProx Module is connected to the network terminals
located at the bottom of the control panel (see pages 13 &
14 for details).
Addressing
The iProx Module is addressed as a keypad and will occupy
a keypad slot on the network. The unit must have a unique
address, which must not conflict with keypad or any other
iProx Module on the same network
The following table shows the addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On off off off
2 off On off off
3 off off On off
4 off off off On
5 On off off On
6 off On off On
7 off off On On
8 On off On On
Refer to the iProx Module manual for programming and
operating instructions.

Programming the Control Panel Premier 640 Installation Manual
18 INS344
60IXD Zone Expander
The 60iXD expander provides the following facilities:
•Two iD loops each supporting up to 30 biscuits
•Fused 12V output for powering detectors
•Engineer’s keypad port for local iD diagnostics
!The 60iXD expander module is only supported on Premier
640 control panels from version 1.0 onwards,
Installation
Before connecting the 60iXD expander module, isolate ALL
power from the control panel (AC mains and battery), do not
continue if there is still power present on the control panel.
1. Connect the iD expander to the control panel, see
60iXD installation manual (INS261) for details.
2. Connect the iD devices to the expander module, see
“iD Connections”.
3. Reapply power to the control panel and program the
necessary options on the panel see 60IXD
installation manual (INS261) for details.
iD Connections
Each iD biscuit is connected across a two-wire detector loop.
Apart from observing the correct polarity, any wiring
configuration can be used, as shown in the diagram below:
60iXD
LOOP 1
+-
09 10 11 12 13
03 04 05 0601 02
08
07
14
LOOP 2
+-
As LOOP 1
* The 60iXD expander module is supplied with 4 off 10nF
capacitors in the spares pack. It is recommended that you
connect a 10nF capacitor approximately at the half way
point of each iD spur. It is especially important to do this on
iD spurs that are less than 30 metres.
Cabling Considerations
The iD loop can be wired using standard 4-core alarm cable,
this allows 2 cores to be used for the iD biscuit and 2 cores
for supplying 12V power for PIR's etc.
The number of biscuits that can be connected per cable run
is determined by the impedance of the cable used. Standard
4-core alarm cable (7/0.2mm) has a resistance of
approximately 8 Ohms per 100 metres. The following table
shows the maximum number of biscuits that can be
connected at the end of a single cable run using standard 4-
core alarm cable:
Cable Length Maximum Number of Biscuits
100m 30
200m 15
400m 7
800m 3
If a different type of cable is used, the distances should be re-
calculated. e.g., if 7/0.4mm cable is used, a single run of
200m would support 30 devices on the end as the resistance
of the cable is halved.
When installing the iD loop it is usually more practical to run
several cables from the expander module to the different
areas of protection. This effectively reduces any distance
problems and makes fault finding much easier.
To reduce the risk of induced interference and wherever
possible, cables should not be positioned along side mains
power, telephone or other data transmission cables, or run
within the same ducting or trunking as any other cables.
The wiring for the system’s internal sounders (loudspeakers)
should not be connected in the same multi-core as the iD
loop.
Biscuit Connections
Each iD biscuit is identified by its own number 01 to 30 and
contains its own internal sensor that is continuously
monitored by the expander module. The diagram below
shows the connections to the biscuit for monitoring both
tamper and alarm contacts.
iD Biscuit
Alarm
Ta m p e r
LOOP +
LOOP -
White
Yellow
Blue
Biscuit iD
01
When the tamper switch is opened, the iD biscuit is taken
offline and a tamper condition is generated by the control
panel. If the alarm switch is opened the biscuit's internal
sensor changes state and the control panel will see this as an
active condition and will respond as appropriate.
The diagram below shows the typical wiring of a biscuit to a
standard PIR.
+12V
ALARM TAMPER
From Expander To next detector
Red
Black
Blue
Yellow
Red
Black
Blue
Yellow
White
Blue
Yellow
0V
“iD” is a registered trade mark of Chloride Safety System Limited.

Premier 640 Installation Manual Installation
INS344 19
OP16 Output Expander
Output Module Layout
Power LED
Ta m p e r
Switch
Network
Te rm in a ls
A
ux 12V
and Tamper
Output
NETWORK IN
+- TR +- TR
NETWORK OUT
Power
1Amp Aux 12v
1
A
mp
2431
BANK 1
Remote
Bank 2
Outputs
1 to 8
1
2
3
4
5
6
7
8
BANK 2
1
2
3
4
5
6
7
8
BANK 1
Bank 1
Outputs
1 to 8
Tmp
-
Aux 12V
++
-
2431
BANK 2
Network
Ter m in a ls
Engineers
Keypad
Interface
Connecting Output Modules
Output modules are connected to the network terminals
located at the bottom of the control panel (see pages 13 & 14
for details).
Output Module Addressing
Each output module must be assigned a different address
using the DIL switches located in the centre of the PCB.
The table below shows the expander addressing:
Address DIL 1 DIL 2 DIL 3 DIL 4
1 On or off Off Off Off 2 431
2 Off On Off Off
2 431
3 Off Off On Off 2 431
4 Off Off Off On 2 431
5 On Off Off On 2 431
6 Off On Off On 2 431
7 Off Off On On
2 431
8 On Off On On
2 431
!In order for an output module to mimic zone expander
outputs, the output module must be addressed the
same as the zone expander that it is mimicking.
Any combination of addresses can be used on each
output module i.e. Bank 1 can be addressed to mimic
expander 3 and Bank 2 can be addressed to mimic
expander 8.
Bank 1 switch sets the address of the device that Bank
1 outputs 1 to 8 will mimic.
Bank 2 switch sets the address of the device that Bank
2 outputs 1 to 8 will mimic.
Output Module Numbering
The table below shows the output allocation when the output
modules are installed:
Address Outputs
(Network 1)
Outputs
(Network 2) **
1 Expander 1, 1 - 8 Expander 1, 1 - 8
2 Expander 2, 1 - 8 Expander 2, 1 - 8
3 Expander 3, 1 - 8 Expander 3, 1 - 8
4 Expander 4, 1 - 8 Expander 4, 1 - 8
5 Expander 5, 1 - 8 Expander 5, 1 - 8
6 Expander 6, 1 - 8 Expander 6, 1 - 8
7 Expander 7, 1 - 8 Expander 7, 1 - 8
8 Expander 8, 1 - 8 Expander 8, 1 - 8
Outputs
The output module has 16 programmable outputs, which can
be used to drive auxiliary devices such as LED’s, sounders or
relays etc. Wire as per Panel Outputs shown on page 23 (see
page 60 for details). The electrical characteristics for the
outputs are shown below:
Bank Outputs Max Current Type
1 1 to 8 100mA Switched -ve
2 1 to 8 100mA Switched -ve
Tamper Output
The tamper switch on the output module is connected to the
tamper output at the top of the module. If monitoring of the lid
tamper is required, this output must be connected to a
suitable input on the control panel or zone expander.

Programming the Control Panel Premier 640 Installation Manual
20 INS344
Zone and Output Numbering
Expander Zones
Address Zones
Network 1
Zones
Network 2
Zones
Network 3
Zones
Network 4
Zones
Network 5
Zones
Network 6
Zones
Network 7
Zones
Network 8
1 1 - 8 65 - 72 129 - 136 193 - 200 257 - 264 321 - 328 385 - 392 449 - 456
2 9 - 16 73 - 80 137 - 144 201 - 208 265 - 272 329 - 336 393 - 400 457 - 464
3 17 - 24 81 - 88 145 - 152 209 - 216 273 - 280 337 - 344 401 - 408 465 - 472
4 25 - 32 89 - 96 153 - 160 217 - 224 281 - 288 345 - 352 409 - 416 473 - 480
5 33 - 40 97 - 104 161 - 168 225 - 232 289 - 296 353 - 360 417 - 424 481 - 488
6 41 - 48 105 - 112 169 - 176 233 - 240 297 - 304 361 - 368 425 - 432 489 - 496
7 49 - 56 113 - 120 177 - 184 241 - 248 305 - 312 369 - 376 433 - 440 497 - 504
8 57 - 64 121 - 128 185 - 192 249 - 256 313 - 320 377 - 384 441 - 448 505 - 512
Keypad Zones
Address Zones
Network 1
Zones
Network 2
Zones
Network 3
Zones
Network 4
Zones
Network 5
Zones
Network 6
Zones
Network 7
Zones
Network 8
1 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
2 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
3 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
4 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
5 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
6 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
7 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
8 Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped Unmapped
Expander/OP16 Outputs
Address Outputs
Network 1
Outputs
Network 2
Outputs
Network 3
Outputs
Network 4
Outputs
Network 5
Outputs
Network 6
Outputs
Network 7
Outputs
Network 8
1 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8 Exp. 1, 1-8
2 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8 Exp. 2, 1-8
3 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8 Exp. 3, 1-8
4 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8 Exp. 4, 1-8
5 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8 Exp. 5, 1-8
6 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8 Exp. 6, 1-8
7 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8 Exp. 7, 1-8
8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8 Exp. 8, 1-8