The Wings Maker CLIPPED WING CUB - 48 User manual

Before commencing assembly, please read these instructions thoroughly.
THE WINGS MAKER
FACTORY PRE-FABRICATED
ALMOST-READY-TO-FLY (ARF) SERIES
MADE IN CHINA
* Specifications are subject to change without notice.*
It is designed for maximum performance. Please seek advice if one is not familiar with this kind
of engine powered precision model. Operating this model without prior preparation may cause
injuries. Remember, safety is the most important thing. Always keep this instruction manual at
hand for quick reference.
Warning ! This model is not a toy.
Wing Span: 63.0 in /1600 mm
Wing Area: 620 sq in / 40 sq dm
Flying Weight: 5.5 lbs / 2500 g
Fuselage Length: 47.0 in / 1200 mm
Required : 2-stroke 0.40 or 4-stroke 0.52 engine
4-channel radio w/ 5 servos
SpecificationsSpecifications
GA013
CLIPPED WING CUB - 48
www.thewingsmaker.com
INSTRUCTION MANUAL

CLIPPED WING CUB - 48
P.3-P.10
Do not overlook this symbol!
Cut off shaded portion.
Peel off shaded portion
covering film.
Pay close attention here!
Pierce the shaded portion
covering film.
Must be purchased separately!
Drill holes with the specified
diameter (here: 3mm).
3mm
INDEX
BEFORE YOU BEGIN
PARTS LIST
ASSEMBLY
SAFETY PRECAUTIONS
P. 1
P. 2
P. 10
BEFORE YOU BEGIN
Read through the manual before you begin, so you will have an overall idea of what to do.
Symbols used throughout this instruction manual comprise of the following : -
Ensure smooth non-binding
movement while assembling.
Apply instant glue
(C.A.glue, super glue.)
Assemble left and right
sides the same way.
Apply epoxy glue.
1
2
3
P.1
Check all parts. If you find any defective or missing parts contact your local dealer. Please DRY FIT
and check for defects for all parts that will require CA or Epoxy for final assembly. Any parts you
find to be defective after the gluing process may be difficult to remove for warranty replacement. The
manufacturer will replace any defective parts. but will not extend to the parts that are good before
gluing to defective parts during assembly. Warranty will not cover any parts modified by customer.
Apply thread locker

Parts List
P.2
COVERING:--
TOUGHLON STL251 SKY BLUE
TOUGHLON STL312 BRIGHT RED
LIGHTEX SGX100 WHITE
1. MAIN WING -- 1 pair
2. SCREW PWA2x12mm -- 8 pcs
PLYWOOD 2x52x80mm (For Aileron Servo) -- 1 pair
BALSA 8x18x21mm (For Aileron Servo) -- 4 pcs
3. SCREW PM2x20mm -- 4 pcs
FUEL TUBE Ø6x5mm -- 4 pcs
CLEVIS (L) -- 2 pcs
STRAPER (L) -- 2 pcs
HORN (L) -- 2 sets
PUSHROD Ø1.8x90mm w/ Threads(For Aileron) -- 2 pcs
4. PLYWOOD 2x30x120mm (Wing Protection) -- 1 pc.
WING TUBE Ø9.6x246mm -- 1 pc.
5. SCREW PM3x18mm -- 4 pcs
MAIN WING STRUTS -- 1 pair
6. FUSELAGE -- 1 pc.
VERTICAL FIN & RUDDER -- 1 set
STABILIZER & ELEVATOR -- 1 set
7. SCREW PA3x12mm -- 2 pcs
TAIL LANDING GEAR -- 1 set
TAIL WHEEL Ø25mm -- 1 pc.
COLLAR Ø2.1mm w/ set screw -- 1 set
SCREW PM2x12mm -- 1 pc.
M2 NUT -- 1 pc.
ALUMINUM PLATE 0.5mm -- 1 pc.
8. ENGINE MOUNT PL5111050 -- 1 set
SOCKET HEAD SCREW M4x25mm -- 4 pcs
WASHER d4xD9mm -- 4 pcs
9. SCREW PM3x25mm -- 4 pcs
WASHER d3xD7mm -- 8 pcs
M3 NUT -- 8 pcs
THROTTLE PUSH WIRE Ø1.2x340mm -- 1 pc.
w/ Plastic Tube d2xD3x250mm -- 1 pc.
10. FUEL TANK 260cc -- 1 set
BALSA 10x10x112mm (For Fixing Fuel Tank) -- 1 pc.
11. SCREW PM3x20mm -- 2 pcs
SCREW PA3x8mm -- 6 pcs
WASHER d3xD7mm -- 2 pcs
M3 NUT -- 2 pcs
ALUMINUM PLATE 1.5mm -- 2 pcs
MAIN LANDING GEAR -- 1 set
MOUNTING PLATE 12x20mm -- 4 pcs
12. SCREW PA1.7x8mm -- 6 pcs
MAIN WHEEL PL3112080 -- 2 sets
COLLAR Ø3.3mm w/ set screw -- 4 sets
SCREW PM2x8mm -- 6 pcs
WASHER d2xD5mm -- 6 pcs
M2 NUT -- 6 pcs
COPPER PLATE 0.5mm -- 6 pcs
BALSA 2x102x113mm (Main Landing Gear Cover) -- 1 pair
13. SCREW PWA2.3x8mm -- 4 pcs
WIND SHIELD -- 1 pc.
SILICON GROMMET d1.5x6.5mm -- 4 pcs
SIDE WINDOWS -- 1 pair
14. COWLING -- 1 pc.
TRANSPARENT DUMMY COWLING -- 1 pc.
SCREW PWA2.6x12mm -- 4 pcs
SILICON GROMMET d1.5x6.5mm -- 4 pcs
DUMMY ENGINE COVER -- 1 pair
15. LINKAGE CONNECTOR Ø2.1mm -- 1 set
16. SCREW PM2x16mm -- 7 pcs
FUEL TUBE Ø6x5mm -- 3 pcs
CLEVIS (L) -- 3 pcs
HORN (L) -- 2 sets
TRI-HORN M3x14mm (S) -- 1 set
PUSH ROD Ø1.8x725mm w/ Threads (For Rudder) -- 1 pc.
PUSH ROD Ø1.8x610mm w/ Threads (For Elevator) -- 2
17. PUSHROD Ø1.8x115mm (For Elevator) -- 1 pc.
PUSHROD CONNECTOR 4x9x20mm -- 1 set
SPONGE 70x90x105mm -- 1 pc.
PLYWOOD 3x57x115mm (For Fuselage Servos) -- 1 pc.
BALSA 6x8x108mm (For Fuselage Servos Stand) -- 2 pcs
STRAPER -- 2 pcs
FUEL TUBE Ø6x5mm -- 2 pcs
18. BALSA 3x45x108mm (For Pilot) -- 1 pc.
BALSA 6x8x45mm (For Pilot Stand) -- 2 pcs
SCREW PWA2x8mm -- 4 pcs
19. SCREW PM4x30mm -- 2 pcs
WASHER d4xD15mm -- 2 pcs
SCREW PM3x9mm -- 2 pcs
M3 NYLON INSERT LOCK NUT -- 2 pcs
20. DECALS -- 1 set

Main Wing
1
Pre-glued
Main Wing
2
PWA2X12mm Screw
8
Cut away covering for installing the servo as shown.
Use the fishing line supplied inside the wing to lead
the servo lead to the openings of wing center.
PWA2x12mm
Make a slot into the hatch
for the servo horn to come out.
2mm
1mm
Aileron Servo.
Extension lead to
aileron servo.
Main Wing
3
PM2x20mm Screw
4
PM2x16mm
Ø1mm pilot holes for The Wings Maker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
2mm
P.3

Vertical Fin / Horizontal Stabilizer
6
90
Make sure vertical fin and stabilizer are at right angles.
Temporary insta ll the main wing, adjust
leve ling of the stabilizer to make it as
para llel to the main wing as possible.
(Stabilizer)
(Main Wing)
B B'
B=B'
Wing Struts
5
PM3x18mm Screw
4
558mm
95mm
189mm
PM3x18mm
Thread Locker
Main wing
4
2x30x120mm Plywood
Aluminum Tube
Ø9.6 x 246mm
Join the wing halves by using the aluminium tube supplied
Strengthen both holes for the screws with a piece of plywood.
P.4

Tail Landing Gear
7
PA3x12mm Screw
3mm Set Screw
2mm Collar
PM2x12mm Screw
2
1
1
1
M2 Nut
1
3mm Set Screw
PM2 x 12 mm
PA3 x 12mm
Engine Mount
8
M4x25mm Socket Head Screw
4
4
d4xD9mm Washer
M4x25mm
Engine
9
PM3x25mm Screw
8
3mm Washer
8
M3 Nut
Lead the 1.2mm throttle rod through the
plastic tube and attach the throttle rod
to the throttle lever on the engine.
Install Engine position
PM3 x 25mm
115mm
4.53in
Fire
Wall
3mm Washer
3mm Washer
d4xD9mm Washer
M3 Nut
P.5

12
2.1mm
3mm Set Screw 2mm Washer
PM2x8mm
Copper clipper
PM2x8mm Screw
PA1.7X8mm Screw
2mm Washer
6
6
6
6
4
3mm Set Screw
4
Collar
PM2x8mm
PA1.7X8mm
2mm Washer
Fuel Tank
10 Fuel Tank
260cc
Sponge sheet
Install Balsa110x10x10mm
(For fixing) fuel tank Position
Fuel Tank
Bottom View
Main Landing Gear
11
PM3x20mm Screw
PA3x8mm Screw
3mm Washer
2
6
2
2
2mm
PA3 x 8mm PM3x20mm
3.1mm
3mm Washer
260cc
Fuel Tank
P.6
UP
Main Landing Gear
M2 Nut
M2 Nut
M3 Nut
M3 Nut

Canopy
13
PWA2.3x8mm Screw
d1.5x6.5mm Silicon Grommet
4
4
d1.5x6.5mm
Silicon
Grommet
PWA2.3x8mm
Securely glue the windows to the fuselage.
Cowling
14
PWA2.6x12mm Screw
d1.5x6.5mm Silicon Grommet
4
4
PWA2.6x12mm
d1.5x6.5mm
Silicon Grommet
Trim the cowling for the
engine head to project.
1.5mm
Servo Set
15
Throttle Pushwire.
2mm
2mm
3mm
Included with the radio set.
Included with the radio set.
Please refer to attached sheet for linkage connector installation.
Throttle Servo
d2xD5mm Washer
2mm Nut
3mm Set Screw
1
2
1
1
LINKAGE CONNECTOR
2mm
2mm
P.7
Please refer to the attached
sheet for usage of the
transparent 3D template.

Rudder&ElevatorPushrod
16
P.8
Radio Equipment
17 Install and arrange the servos as shown in the diagram.
Fuel Tank
Receiver
Battery
Straper
Rudder
Ø1.8x725mm
Pushrod
Fuel Tube
Ø6x5mm
PM2 x 16mm Screw
7
Fuel Tube
Rudder
Tri-horn
Tri-horn
3 x 14mm
Clevis
PM2 x 16mm
Rudder
Pushrod Elevator
Pushrod
Make both push rod set it as shown in the diagram.
Bottom View
Elevator
Horn
PM2 x 16mm
Clevis
Fuel Tube
6 x 5mm
Horn
2mm
Ø1mm pilot holes for The Wings Maker tri-horn are pre-drilled.
Please look for pin-hole marks at under side of control surfaces.
2mm
Elevator Pushrod
Ø1.8x610mm
Elevator Servo
Elevator Servo
Throttle Pushrod
Ø1.2x340mm
Throttle Servo
Elevator Servo
KM 2x8mm
M2 Nut
Elevator Pushrod
Ø1.8x115mm

19
Main Wing/Wing Struts
PM4 x 30mm Screw
4mm Washer
PM3 x 9mm Screw
M3
Nylon Insert Lock Nut
2
2
2
2
3mm
PM3 x 9mm
4mm Washer
PM4 x 30mm Screw
M3Nylon Insert Lock Nut
Cockpit
18
PWA2x8mm Screw
4
1.5mm
Balsa
3 x 45 x 110mm
6 x 8 x 45mm
Balsa
P.9

Wing Setting
20
A = A'
B = B'
C = C'
D = D'
C C'
D D'
B B'
A A'
In order to obtain the wing and fuselage configuration as in the
diagrams, insert reinforcement plates between the wing and fuselage
if necessary.
Securely attach the
main wing
Control Throws
21
Rudder
Elevator
Aileron
25mm
25mm
20mm
20mm
10mm
10mm
Adjust the control throws as shown in
the diagram. These throws are good for
general flying. You can adjust according
to your personal preference.
C.G.
22
70mm
2.76in
The ideal C.G. position is 70mm (2.76 in) behind
the leading edge measured at where the wing
meets the fuselage. In order to obtain the C.G.
specified, add weight to the fuselage or move
the battery position. Check the C.G. before
flying.
P.10

P.11
Important Safety Precautions
#First time flyer should never fly by himself / herself. Assistance from experienced flyer is
absolutely necessary.
#Pre-flight adjustment must be done before flying, it is very dangerous to fly a badly
pre-adjusted aircraft.
# is specially designed to be powered by 2C 40 or 4C 52 engine,
CLIPPED WING CUB - 48
using a more powerful engine does not mean better performance. In fact, over powered
engine may cause severe damage and injuries.
#Make sure the air field is spacious, never fly the plane too close to people and never get
too close to a running propeller.
#If you find wrinkles on the covering as a result of weather changes, you can use hot iron
to remove the wrinkles. Please begin with lower temperature setting and gradually raise
the temperature until the wrinkles are gone. Too hot an iron may damage the covering.
#Check and re-tighten up all factory assembled screws, use thread locker if applicable.
GA0130708
www. thewingsmaker.com
THE WINGS MAKER