Thermaltake C240 User manual

C240 DDC SOFT TUBE LIQUID COOLING KIT
Intel LGA 775,LGA115x,LGA1366
Intel LGA2011,2011-3
AMD
1.FM2/FM1/AM3/AM2
2.AM4
3.LGA1366
4.LGA1150/1151/1155/1156
5.LGA775
CPU Water Block Installation Guide
© 2019 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
1
06
06
05
05
05
07
07
07
01
01
01 01
09
09
02
02
10
10
10
03
03
04
04
08
1
1
1 3
2
2
24

C240 DDC SOFT TUBE LIQUID COOLING KIT
3
2
Installation Guide
To ensure a clean loop, flush and rinse your radiators
and water blocks with distilled water before using.
Make sure the fittings are screwed securely when
placing them onto the radiator.
Attach the fittings to the inlet and outlet of the water block.
Radiator Water Block
Installation Walkthrough (Example: A500 TG)
Place the motherboard into the case. Position the radiator. Attach the pump and reservoir into
the chosen locations.
1
2
27
01
26
27
23
22
21
Attach the fans to the radiator
Case Fan
20
24
Connect the PWM
cable to motherboard. 31
Connect the fan power cable to PWM cable
2031
21
Connect the fan power cable when the liquid cooling system
is completely finished
26
27
27
12
CAUTIONS:
Make sure there is enough space when you start to set up the LCS product
or
12 12
15
14
18
13
15
16
16
14
Attach fittings onto the pump and reservoir
Pump / Reservoir
Choose the proper way to mount the pump and reservoir by referring to the manual
(suggest vertical placement)

C240 DDC SOFT TUBE LIQUID COOLING KIT
Thermaltake recommends the following steps to be taken after completing your water loop setup
1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance
while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
4. Fill the reservoir to the top as it will prevent air from going into the pump
5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
6. Place some paper towels under fittings and joining points to test for leaks.
7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cutting and Attaching the Tubing
3
4
3
2
2
1
1
Filling the System
CAUTIONS:
1. Before filling the system, please make
sure that each fitting as well as unused
ports are completely sealed.
2. If there is any case of leaking,
immediately turn off the power and
clean the leak
3. If there is any related electronic parts
stained on liquid coolant, make sure to
completely clean and dry the
components. And then make sure they
all work well.
After switching off the power supply,
connect the PSU power cord and
product cables.
Use the refill bottle to fill coolant into the reservoir
Place your PSU outside of the case and attach it to
the pumps 4pin molex connector, turn on the power
of PSU and make the rest of the system fills up.
3
34 35
Take out the cap from the fittings and place
the cap of the compression fitting over the
tubing. Push the end of the tubing over the
barb; make sure the tubing is a tight fit.
Slide the cap over the fitting and rotate it
clockwise until the tubing is sealed in place.
Measure the tube length based on the fitting,
and make (cut) the tubes. The loop order :
Pump Outlet > Water Block
Measure the tube length based on tfitting,
and make (cut) the tubes. The loop order :
Water Block > Radiator
Measure the tube length based on the
fitting, and make (cut) the tubes.
The loop order : Radiator > Reservoir inlet

C240 DDC SOFT TUBE LIQUID COOLING KIT
Motherboard SYNC installation Guide
CAUTIONCAUTION
1. Light Mode:
Switch over between 7 LED modes.
3. Light Speed:
Switch over between 4 light modes.
When light mode is in RGB Spectrum:
Click to memorize and lock the color you want, click again to unlock the 256
colors auto rotation.
Red → Yellow → Green → Teal → Blue → White → Purple
When light mode is in Ripple :
Switch over 7 LED colors .
When light mode is in Wave and Flow :
LED color can not be adjusted.
Red → Yellow → Green → Teal → Blue → White → Purple → Rainbow
2. Color Mode:
When light mode is in Full Lighted, Pulse and Blink :
Switch over 8 LED colors .
Wave → Full light → RGB Spectrum → Off → Flow → Ripple → Pulse → Blink
Slow → Normal → Fast → Extreme
Connect the Motherboard Signal Bridge Cable to fan led cable
Please power off the PC and check
the Positive and Negative ends on
the connector before connecting
the cable to motherboard. Connecting
the wrong end can damage the LEDs.
Aura Addressable Strip Header(s) Addressable RGB LED Header(s) AORUS RGB Fusion with Digital LEDs
ASUS ASROCK GIGABYTE
JRGB-strip Header(S)
MSIMSI
+5V D G
JRAINBOW
G
1
2
Connect the ARGB controller to the Fans.
Connect the ARGB controller to the SATA connector.
ARGB Controller Installation Guide
4
29
29 29 29 30
32
32
20
20
11
11
01
01
30