Thermaltake CLM360 User manual

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
01 x 1 02 x 1 03 x 1 04 x 4 05 x 4 06 x 1
Parts List
This product is intended for installation only by expert users. Please consult with a qualified technician for installation.
Improper installation may result in damage to your equipment. Before you start using this product please follow these basic guidelines:
1. Please carefully read the manual before beginning the installation process !
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant.
3. Please remove your graphics card from your motherboard to ensure the safest process and in order to prevent any possible damages to your CPU and motherboard.
4. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either !
07 x 1 08 x 1 09 x 1 10 x 4 11 x 4 12 x 4
CPU Water Block
Pump / Reservoir
Fan & Radiator
Accessory
14 x 113 x 3
19 x 2 20 x 8 21 x 1 22 x 1 23 x 8 24 x 1 25 x 1
26 x 1 27 x 1 28 x 1 29 x 1 30 x 1 31 x 1 31 x 132 x 1 33 x 1
15 x 12 16 x 12 17 x 12 18 x 1
1

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
CPU Water Block Installation Guide
© 2021 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
2
This product is intended for installation only by expert users. Please consult with a qualified technician for installation.
Improper installation may result in damage to your equipment.
Before you start using this product please follow these basic guidelines:
1. Please carefully read through the instruction manual before beginning the installation process.
2. Please remove your graphics card from your motherboard to insure the safest process and in order to prevent any possible damages
to your CPU and motherboard.
3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant Series.
1
2
Intel LGA 1200/115X
AM3/AM2/
AM4
FM2/FM1
a
b
ab
AMD
ab
LGA1700
LGA1200/1156/1155/1151/1150
a
b
a
b
ba
Intel
12
Intel LGA 1700
3
45 6
Please make sure the grey
mark is toward to the TT Logo.
05
05
01
01
06
03 02 03
03
04
01
06
03
04
01

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
3
45
6 7
Out : Circle 1 is designed for liquid outlet
In : Circle 2 is designed for liquid inlet/fill
1
2
MB SYNC Installation Guide
CAUTIONCAUTION
1 2
To control the LCD display by
TT RGB PLUS Software,
Please connect the water block
and motherboard with cable G.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference,
and (2) this device must accept any interference received, including interference that may cause undesired operation.
Installation Guide
1 2
Please make sure the grey
mark is toward to the TT Logo.
AMD
123
01
01 02
01
02
06
03
04
31
31

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
Installation Guide
CAUTIONS: 1. Make sure there is enough space when you start to set up the LCS product
2. Please use the wrench to install/ uninstall the base parts during all the installation
To ensure a clean loop, flush and rinse your radiators
and water blocks with distilled water before using.
Make sure the fittings are screwed securely when
placing them onto the radiator.
Attach the fittings to the inlet and outlet of the
water block.
Radiator
Fitting Water Block
Installation Walkthrough (Example: A500 TG)
Place the motherboard into the case. Position the radiator. Attach the pump and reservoir into
the chosen locations.
3
2
1
Nut
O-Ring
Packing
Base
Dismantle the fitting by using the wrench
1
2
4
01
Attach the fans to the radiator
Case Fan
or
Choose the proper way to mount the pump and
reservoir by referring to the manual
(suggest vertical placement)
Attach fittings onto the pump
and reservoir
Pump / Reservoir
Base
18 20
14
14
13
20
20
20
20
19
19
22
21
07
07
08
09
08
09
12
12
10
10
17
15 16
11

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
Thermaltake recommends the following steps to be taken after completing your water loop setup
1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance
while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
4. Fill the reservoir to the top as it will prevent air from going into the pump
5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
6. Place some paper towels under fittings and joining points to test for leaks.
7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
Cutting and Attaching the Tubing
Measure the tube length based on the base
part of the fitting, and make (bend) the tubes.
The loop order : Pump Outlet > Water Block
Measure the tube length based on the base
part of the fitting, and make (bend) the tubes.
The loop order : Water Block > Radiator
Measure the tube length based on the
base part of the fitting, and make (bend)
the tubes. The loop order : Radiator >
Reservoir inlet
Fit the C-Pro fitting to the tube according
to the order in the picture below, Install the
tubes and tight the fitting caps.
Finished
3
3
2
2
1
1
4 5
Filling the System
CAUTIONS:
1. Before filling the system, please make sure
that each fitting as well as unused ports are
completely sealed.
2. If there is any case of leaking, immediately
turn off the power and clean the leak
3. If there is any related electronic parts stained
on liquid coolant, make sure to completely
clean and dry the components. And then
make sure they all work well.
After switching off the power supply, connect the PSU
power cord and product cables.
Use the refill bottle to fill coolant into the reservoir
Place your PSU outside of the case and attach it to the pumps 4pin molex
connector, turn on the power of PSU and make the rest of the system fills up.
CA UTIONCA UTION
The O-ring and the packing
with a groove on the inside
diameter must always be
installed towards the top of
the compression nut
Groove
5
Keep the reservoir cap dry!
Do not allow coolant to
access the wire and
the LED module
Caution!
After adding the recommended coolant, remember to fill the reservoir to only 80%
and leave the fill port cap off. This will help stabilize your internal loop pressure
23
20
25
29
29
28

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
6
Installation Guide
1
3
2
Connect the plug into the port in numerical order,
start with plug one.
4
Connect the controller cable onto the mainboard
(USB 2.0 9 pin) and controller.
5
Connect the power cable to the 4pin Molex connecter
and controller.
ON
1 2 3 4
Connect the Bridge Cable to the Controller
Set the DIP switch on the back side of the controller to assign the number of the controller.
ON
1 2 3 4
NO.1 NO.2
© 2021 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
29
13
31
31
32
32
30 30

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
7
TT RGB Plus Software control interface
Please download TT RGB PLUS from Thermaltake's Official website.
https://www.thermaltake.com/downloads
OS compatibility: Windows 10
LIGHTING
software interface may vary with feature update,
please download the latest user manual from our
www.thermaltake.com
Pacific MX2 Ultra CPU Water Block Software User Interface
A. After installation of TT RGB PLUS, you can select
“TOUGHLIQUID ULTRA” on the “Pacific MX2 Ultra” page.
B. Preset the CPU water block LCD.
C. LCD DISPLAY function list.
• GIF & JPG (Upload picture to LCD display)
• CPU TEMP.
• CPU CLOCK SPEED
• CPU LOAD
• GPU TEMP.
• GPU CLOCK SPEED
• GPU LOAD
• LIQUID TEMP.
• CAROSUEL (Switches between CPU/GPU/Liquid information)
D. LCD visual effect settings.
Set LCD display background, text and visual color,
screen brightness or turn off LCD screen.
SETTINGS
GIF & JPG
BB
CC
AA
AA
DD
CC
BB
AA
CC
BB
A. Select “GIF & JPG” form “LCD DISPLAY”. You
can upload a GIF or JPG file to show the picture
on the LCD screen. (Max size: 20MB)
B. Set the LCD display text information, speed and
brightness, or turn off LCD screen.
C. Click “UPLOAD” to upload the picture. (GIF and
JPG files only)
A. Click the gear icon on the upper right corner to
enter the “SETTINGS” menu.
B. Upload the picture to set as LCD boot animation.
(GIF only, Max size: 5MB)
C. Upload the picture to set as LCD standby screen.
(JPG only, Max size: 5MB)

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
8
TT RGB Plus Software control interface
Please download TT RGB PLUS from Thermaltake's Official website.
https://www.thermaltake.com/downloads
OS compatibility: Windows 10
Connect
software interface may vary with feature update,
please download the latest user manual from our
www.thermaltake.com
Riing Duo RGB Radiator Fan Software User Interface
A. After installation of TT RGB PLUS, you can see several
controllers installed on the “CONNECT” page.
B. Click the controller port to make the Riing Duo LEDs
glow red lighting to pair.
C. Drag & drop to pair the Riing Duo Plus with controller.
D. Show the controller DIP number.
E. Save and reset controller pairing settings.
LIGHTING
AA
DD
EE
CC
BB
AA
CC
BB
A. You can see Riing Duo on “LIGHTING” page.
B. Preview and edit Riing Duo LEDs lighting effect.
C. TT RGB PLUS provides 23 kinds of lighting effects.

PACIFIC CLM360 ULTRA LIQUID COOLING KIT
CL-W335-CU12SW-A
9
TT RGB Plus Software control interface
Please download TT RGB PLUS from Thermaltake's Official website.
https://www.thermaltake.com/downloads
OS compatibility: Windows 10
Connect
software interface may vary with feature update,
please download the latest user manual from our
www.thermaltake.com
Pacific PR32-D5 Plus Software User Interface
A. After installation of TT RGB PLUS, you can see several
controllers installed on the “CONNECT” page.
B. Click the controller port to make the PR32-D5 Plus
LEDs glow red lighting to pair.
C. Drag & drop to pair the PR32-D5 Plus with controller.
D. Show the controller DIP number.
E. Save and reset controller pairing settings.
LIGHTING
AA
DD
EE
CC
BB
AA
CC
BB
A. You can see PR32-D5 Plus on “LIGHTING” page.
B. Preview and edit PR32-D5 Plus LEDs lighting effect.
C. TT RGB PLUS provides 23 kinds of lighting effects.