Thermaltake Pacific V-RTX 3080/3090 Plus User manual

VGA Water Block
Pacific V-RTX 3080/3090 Plus
A x 1 B x 1 C x 10 D x 3 E x5 F x 5 H x 2 I x 1
Q x 10
R x 4
G x 2
2
Cut the thermal pads to the dimensions listed and place them on the spots shown on the diagram.Disassemble the thermal module (cooler) of the graphics
card and clean the thermal paste from the GPU
Cut the thermal pads to the dimensions listed and place them
on the spots shown on the diagram.
When installing the water block, carefully position the water block with the preinstalled standoffs on the graphics card.
Parts List
Apply thermal compound
Finish
1
5
This product is intended for installation only by expert users. Please consult with a qualified technician for installation. Improper installation may result in damage to your equipment.
Before you start using this product please follow these basic guidelines:
1. Please carefully read through the instruction manual before beginning the installation process.
2. Please remove your graphics card from your motherboard to insure the safest process and in order to prevent any possible damages to your CPU and motherboard.
3. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000.
Q
R
I
4
3
1.2mm
1.2mm
2.5mm
2.5mm
A
JJ
A
JJ
B
KK
C
LL
D1
+
D2
D1
+
D2
E1
+
E2
H F G
51
51
51
51
100
100
80
80
80
13
13
10 10
39
39
10
13
13
13
12
13
9
9
9
unit : mm
unit : mm
A
J
J
A
B
K
C
L
D1
D1 E1
D2
E2
F
G
H
6
E
C
DG
F
BC
A
210 mm
297 mm
刀模線
105G是X X 雙銅 單色 無無
其他特殊處理效果表面處理
2
厚度(g/m )
折數 材質雙面印刷 印刷色彩單面印刷
規格樣式
單張 CHECK DESIGN
藍色線條為尺寸標示，請勿印刷上去！
Peipei
(20/11/20)
Aan
(20/11/20)
產品料號
C L - W 3 1 1 - C U 0 0 S W - A P a c i f i c V - R T X 3 0 8 0 3 0 9 0 P l u s A S U S S t r i x 說明書 20/11/2 0 A
產品名稱 印刷項目 發稿日期 版本

VGA Water Block
Pacific V-RTX 3080/3090 Plus
Parts List
Installation Guide
7
9
10
11 12
8
J
N
Connect the Waterblock onto the controller.
J
A
N
123
45
Set the DIP switch on the back side of the controller to assign the
number of the controller
J
NO.1
ON
1 2 3 4
NO.3
ON
1 2 3 4
NO.2
ON
1 2 3 4
NO.4
ON
1 2 3 4
NO.9
ON
1 2 3 4
NO.1 1
ON
1 2 3 4
NO.1 0
ON
1 2 3 4
NO.1 2
ON
1 2 3 4
NO.5
ON
1 2 3 4
NO.7
ON
1 2 3 4
NO.6
ON
1 2 3 4
NO.8
ON
1 2 3 4
NO.1 3
ON
1 2 3 4
NO.1 5
ON
1 2 3 4
NO.1 4
ON
1 2 3 4
NO.1 6
ON
1 2 3 4
K
K
Connect the controller cable onto the mainboard (USB 2.0 9 pin)
and controller.
If you want to connect two or more connectors, you can use the bridge
cable to connect the controllers.
M M
Connect the power cable to the 4pin Molex connecter and controller.
L L
Jx 1 Kx 1 Lx 1 Mx 1 Px 1Nx 1 Ox 1
Controller Power Cable Velcro Controller Cable Bridge Cable LED Y - Cable MB SYNC Cable
© 2021 Thermaltake Technology Co., Ltd. All Rights Reserved. www.thermaltake.com
Connect the LED Y-Cable onto the waterblock.
ON
1 2 3 4
210 mm
297 mm
刀模線
105G是X X 雙銅 單色 無無
其他特殊處理效果表面處理
2
厚度(g/m )
折數 材質雙面印刷 印刷色彩單面印刷
規格樣式
單張 CHECK DESIGN
藍色線條為尺寸標示，請勿印刷上去！
Peipei
(20/11/20)
Aan
(20/11/20)
產品料號
C L - W 3 1 1 - C U 0 0 S W - A P a c i f i c V - R T X 3 0 8 0 3 0 9 0 P l u s A S U S S t r i x 說明書 20/11/2 0 A
產品名稱 印刷項目 發稿日期 版本