Thermaltake M360 Plus User manual

3
2
This product is intended for installation only by expert users. Please consult with a qualified technician for installation.
Improper installation may result in damage to your equipment.
1. Please carefully read the manual before beginning the installation process !
2. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant.
3. DO NOT USE any kind of alcohol or alcohol derivatives with this reservoir or the acrylic tube may crack and fail ! Do not clean it using alcohol either !
Before Installation
To ensure a clean loop, flush and rinse your radiators
and water blocks with distilled water before using.
Make sure the fittings are screwed securely when
placing them onto the radiator.
Attach the fans to the radiator
Choose the proper way to mount the pump and reservoir
by referring to the manual (suggest vertical palcement) Attach fittings onto the pump and reservoir
Attach the fittings to the inlet and outlet of the
waterblock.
Attach the waterblock onto the motherboard by
referring to the enclosed manual.
Radiators
Fitting Case Fan
Pump and Reservoir
Water Blocks
Installation Walkthrough (Example: Core P5)
Place the motherboard into the case. Position the radiator. Attach the pump and reservoir into
the chosen locations.
1
Pacific Series M360 Plus
or
Base
Dismantle the fitting by using the wrench
CAUTIONS: 1. Make sure there is enough space when you start set up the LCS product
2. Please use the wrench to install/ uninstall the base parts during all the installation
Nut
O-Ring
Packing
Base
1
2

Cutting and Attaching the Tubing
Measure the tube length based on the base
part of the fitting, and make (bend) the tubes.
The loop order : Pump Outlet > Water Block
Measure the tube length based on the base
part of the fitting, and make (bend) the tubes.
The loop order : Water Block > Radiator
Measure the tube length based on the
base part of the fitting, and make (bend)
the tubes. The loop order : Radiator >
Reservoir inlet
Fit the C-Pro fitting to the tube according
to the order in the picture below, Install the
tubes and tight the fitting caps.
Finished
3
3
2
2
1
1
4 5
Filling the System
CAUTIONS:
1. Before filling the system, please make
sure that each fitting as well as unused
ports are completely sealed.
2. If there is any case of leaking,
immediately turn off the power and
clean the leak
3. If there is any related electronic parts
stained on liquid coolant, make sure to
completely clean and dry the
components. And then make sure they
all work well.
After switching off the power supply,
connect the PSU power cord and
product cables.
Use the refill bottle to fill coolant into the reservoir
Place your PSU outside of the case and attach it to
the pumps 4pin molex connector, turn on the power
of PSU and make the rest of the system fills up.
Thermaltake recommends the following steps to be taken after completing your water loop setup
1. It is strongly recommended to use market proven pre-mix coolant, such as Thermaltake Coolant 1000. It offers great performance
while preventing the entire cooling system – copper, brass, nickel, aluminum, and steel – from corrosion.
2. Fill the reservoir with coolant and cycle the power on and off several times while the pump pushing the coolant into the loop.
3. DO NOT let the pump run dry, when there is no liquid entering the pump turn off your power immediately
4. Fill the reservoir to the top as it will prevent air from going into the pump
5. If necessary tilt the system slightly from side to side to bleed the air out of the loop.
6. Place some paper towels under fittings and joining points to test for leaks.
7. Run the loop with the fill port open for about 24 hours to completely bleed the air out of the loop.
© 2017 Thermaltake Technology Co., Ltd. All Rights Reserved.
www.thermaltake.com
CAUTIONCAUTION
The O-ring and the packing
with a groove on the inside
diameter must always be
installed towards the top of
the compression nut
Refill bottle
not included
Groove