Thermon Terminator DE-B Beacon Reference guide

Terminator
TM DE-B Beacon
LED End of Circuit Light Kit
INSTALLATION PROCEDURES

Kit Contents
Tools Required
Receiving, Storing and Handling
1. Inspect materials for damage incurred during shipping.
2. Reportdamagestothecarrierforselement.
3. Idenfypartsagainstthepackinglisttoensuretheproper
typeandquantyhasbeenreceived.
4. Storeinadrylocaon.
Dimensions
TerminatorTM DE-B Beacon
Item Quanty Descripon
1 1
ExpediterAssembly
Grommet Compressor
Grommet
Support Base with O-Ring
2 1 LightModuleCover
3 1 Banding Guide
4 1 Banding(ts10"pipeandbelow)
5 1 LED Light Module
210mm
(8.25")
76 mm
(3")
89 mm
(3.5")
64 mm
(2.5")
2 43 5
Order Separately
SCTK Connecon Terminaon Kits (per cable)
SCTK-1D for BSX, RSX, VSX, VSX-HT
SCTK-2D for KSX, HTSX
SCTK-3D for FP, HPT
Order Separately
SCTK Terminal Block Connecon Kits (per cable)
SCTK-1TB for BSX, RSX, VSX, VSX-HT
SCTK-2TB for KSX, HTSX
SCTK-3TB for FP, HPT
Item Quanty Descripon
1 2 ConneconBoots
2 1 Large Wire Nut
3 2 Medium Wire Nuts
4 2 Small Wire Nuts
5 1 RTVTube
6 1 GRW-GGrommet(SCTK-3Donly)
Item Quanty Descripon
1 1 TerminalBlock
2 1 TerminalBlockMounngScrew
3 1 SpliceConneconBoot
4 1 RTVTube
5 1 GRW-GGrommet(SCTK-3TBonly)
61
IP66/Type4X-60°C≤Ta≤+45°C,T6
 -60°C≤Ta≤+55°C,T5
Ordinary&HazardousLocaons
ClassI,Division2,GroupsA,B,C,&D,Zone2IICT6...T5
ClassII,Division2,GroupsF&G,ClassIII
Cercaons/Approvals
Installaon Precauons
• Tominimizethepotenalforarcingandrecausedbyproduct
damageorimproperinstallaonuseground-faultprotecon.
The Naonal Electrical Code (NEC) and Canadian Electrical
Code(CEC)requireground-faultproteconofequipmentfor
eachbranchcircuitsupplyingelectricheattracing.
• Installaon must comply with Thermon requirements and
beinstalled in accordancewiththeNEC,CEC, or anyother
applicablenaonalandlocalcodes.
• Componentapprovalsandperformancerangsarebasedon
theuseofThermonspeciedpartsonly.Usersuppliedpower
conneconngsmustbelistedorceredforintendeduse.
• De-energizeallpowersourcesbeforeopeningenclosure.
• Keependsofheangcableandkitcomponentsdrybeforeand
duringinstallaon.
• Individuals installing these products are responsible for
complying with all applicable safety and health guidelines.
Proper personal protecve equipment, or PPE, should be
ulizedduringinstallaon.ContactThermonifyouhaveany
addionalquesons.
1 2
4
3 5
2 43 51

1. Locatebusconnecon(HPTandFPonly)and
cableasshown.Cutendofcableatangletoaid
inpiercinggrommet.Leaveaddionalcablefor
expansion loop.
3. Slide expediter toward pipe and route cable
throughsupportbaseentry.
4. Insertbanding guideintoexpediterandsnap
into place.
5. Mountexpeditertopipeusingpipeband.Do
notbandovercable.
2. Insert cable into expediter. If mounted on
boomofpipe,punchoutweephole.
Note:ForHPTandFPcable,exchangegrommet
interminatorwithGR-GprovidedinPETK-3.
6. Cutoendofcable.
7. Terminate cable with appropriate SCTK
termination kit. Refer to SCTK installation
instrucons. Push excess cable back through
expediter. Remove braid pigtail. Tape cable
expansion loop to pipe.
8. When using wire connector: Connect
bus wires using small wire nuts (for
BSX, HTSX and KSX) or medium wire
nuts (for RSX, VSX, VSX-HT, HPT and FP).
When using terminal block: See steps 9–11.
Seewiringschemacforconnecondetails.
50mm
(2")
Max.
300mm
(12")
Bus
Connecon
Weep
Hole
101mm
(4")Min.
Do Not Band
OverCable
Wiring Schemac for LED Light
Light Module
ExpediterAssembly
Wire Connector
ExpediterAssembly
Boot
LED Light PigtailHeangCable
Min.
300mm
(12")
INSTALLATION PROCEDURES

CorporateHeadquarters:100ThermonDr•POBox609SanMarcos,TX78667-0609•Phone:512-396-5801•1-800-820-4328
FortheThermonocenearestyouvisitusat...www.thermon.com
  ©Thermon,Inc.•PrintedinU.S.A.•Informaonsubjecttochange.
FormNo.PN50843-0818
Locked
Posion
11. Connectthe buswiresofthe traceheaterto
theterminalblock.
14. To remove cap, de-energize circuit, li latch
mechanism, and unscrew cap.
10. Use the terminal block mounting screw to
mountterminalblocktotheLEDlightmodule.
Bend each pigtail lead around the sides of the
terminalblock.
13. Engage threads. Rotate light module cover
clockwiseandghtencapsecurely.Makesure
latchmechanismisinthelockedposion.
9. WhenusingSCTK-TBConneconKit,rsttrim
exposedbuswiresoftheLEDpigtailto8mm
(.32"),thenconnecttotheterminalblock.
12. Slidethelightmodulecoveroverlightmodule.
Light Module
Cover
8mm(.32")
Lens
ExpediterAssembly
Light Module
Unlocked
Posion
TerminatorTM DE-B Beacon INSTALLATION PROCEDURES