thomann Harley Benton AirBorne Pro Instrument User manual

AirBorne Pro Instrument
Wireless System
User Manual

Thomann GmbH
Hans-Thomann-Straße 1
96138 Burgebrach
Germany
Telephone: [phone]
Internet: www.thomann.de
03.03.2023, ID: 482514 (V5)

Table of contents
1 General information................................................................................................................................. 6
1.1 Further information........................................................................................................................... 7
1.2 Notational conventions.................................................................................................................... 7
1.3 Symbols and signal words............................................................................................................... 8
2 Safety instructions.................................................................................................................................. 10
3 Features....................................................................................................................................................... 13
4 Installation and starting up................................................................................................................ 15
4.1 General Information........................................................................................................................ 15
4.2 Dealing with lithium batteries..................................................................................................... 16
4.3 Receiver............................................................................................................................................... 17
5 Connections and controls................................................................................................................... 19
5.1 Receiver............................................................................................................................................... 19
5.2 Transmitter......................................................................................................................................... 21
6 Operating.................................................................................................................................................... 23
7 Technical specications....................................................................................................................... 28
7.1 Receiver............................................................................................................................................... 28
7.2 Transmitter......................................................................................................................................... 29
8 Plug and connection assignment.................................................................................................... 32
Table of contents
AirBorne Pro Instrument 3
Wireless System

9 Troubleshooting...................................................................................................................................... 33
10 Protecting the environment.............................................................................................................. 35
Table of contents
4AirBorne Pro Instrument
Wireless System

AirBorne Pro Instrument 5
Wireless System

1 General information
This user manual contains important information on the safe operation of the device. Read and
follow all safety notes and all instructions. Save this manual for future reference. Make sure
that it is available to all persons using this device. If you sell the device to another user, be sure
that they also receive this manual.
Our products and user manuals are subject to a process of continuous development. We there‐
fore reserve the right to make changes without notice. Please refer to the latest version of the
user manual which is ready for download under www.thomann.de.
General information
6AirBorne Pro Instrument
Wireless System

1.1 Further information
On our website (www.thomann.de) you will nd lots of further information and details on the
following points:
Download This manual is also available as PDF le for you to download.
Keyword search Use the search function in the electronic version to nd the topics of
interest for you quickly.
Online guides Our online guides provide detailed information on technical basics
and terms.
Personal consultation For personal consultation please contact our technical hotline.
Service If you have any problems with the device the customer service will
gladly assist you.
1.2 Notational conventions
This manual uses the following notational conventions:
General information
AirBorne Pro Instrument 7
Wireless System

The letterings for connectors and controls are marked by square brackets and italics.
Examples: [VOLUME] control, [Mono] button.
The individual steps of an instruction are numbered consecutively. The result of a step is
indented and highlighted by an arrow.
Example:
1. Switch on the device.
2. Press [Auto].
ðAutomatic operation is started.
3. Switch o the device.
1.3 Symbols and signal words
In this section you will nd an overview of the meaning of symbols and signal words that are
used in this manual.
Letterings
Instructions
General information
8AirBorne Pro Instrument
Wireless System

Signal word Meaning
DANGER! This combination of symbol and signal word indicates an
immediate dangerous situation that will result in death or
serious injury if it is not avoided.
WARNING! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in death or serious
injury if it is not avoided.
NOTICE! This combination of symbol and signal word indicates a pos‐
sible dangerous situation that can result in material and
environmental damage if it is not avoided.
Warning signs Type of danger
Warning – danger zone.
General information
AirBorne Pro Instrument 9
Wireless System

2 Safety instructions
This device is intended to be used for the wireless transmission of audio signals from instru‐
ments to ampliers or active speakers. Use the device only as described in this user manual.
Any other use or use under other operating conditions is considered to be improper and may
result in personal injury or property damage. No liability will be assumed for damages resulting
from improper use.
This device may be used only by persons with sucient physical, sensorial, and intellectual
abilities and having corresponding knowledge and experience. Other persons may use this
device only if they are supervised or instructed by a person who is responsible for their safety.
Safety
DANGER!
Danger for children
Ensure that plastic bags, packaging, etc. are disposed of properly and are not within reach of babies and young children. Choking
hazard! Ensure that children do not detach any small parts (e.g. knobs or the like) from the unit. They could swallow the pieces and
choke! Never let children unattended use electrical devices.
WARNING!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium batteries can cause severe injuries. Follow the advice on
the correct handling of lithium batteries in the present section.
Intended use
Safety instructions
10 AirBorne Pro Instrument
Wireless System

NOTICE!
Operating conditions
This device has been designed for indoor use only. To prevent damage, never expose the device to any liquid or moisture. Avoid
direct sunlight, heavy dirt, and strong vibrations. Only operate the device within the ambient conditions specied in the chapter
‘Technical specications’ of this user manual. Avoid heavy temperature uctuations and do not switch the device on immediately
after it was exposed to temperature uctuations (for example after transport at low outside temperatures). Dust and dirt inside can
damage the unit. When operated in harmful ambient conditions (dust, smoke, nicotine, fog, etc.), the unit should be maintained by
qualied service personnel at regular intervals to prevent overheating and other malfunction.
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the external power supply, ensure that the input voltage (AC
outlet) matches the voltage rating of the device and that the AC outlet is protected by a residual current circuit breaker. Failure to do
so could result in damage to the device and possibly the user. Unplug the external power supply before electrical storms occur and
when the device is unused for long periods of time to reduce the risk of electric shock or re.
NOTICE!
Possible damage to lithium-ion batteries through incorrect storage
By deep discharge, lithium-ion batteries can be permanently damaged or lose some of their capacity. Before long breaks, charge the
batteries to around 50 % of their capacity and then switch o the device. Store the device at room temperature or cooler in an envi‐
ronment as dry as possible. If the batteries are stored for a longer period, recharge them to 50 % every three months. Fully charge
the batteries only shortly before use at room temperature.
NOTICE!
Possible staining
The plasticiser contained in the rubber feet of this product may possibly react with the coating of your surface and after some time
cause permanent dark stains. In case of doubt, do not put the rubber feet directly on the surface and use a suitable underlay if neces‐
sary, i.e. felt pads or similar.
Safety instructions
AirBorne Pro Instrument 11
Wireless System

NOTICE!
Electromagnetic compatibility with other electrical equipment
Using the device near radios or TV sets may cause interference. Then increase the distance between the devices.
NOTICE!
Fire hazard due to exceedance of the maximum current
The device can power other devices of identical construction. The current consumption of all other devices connected in series must
not exceed the values indicated in the technical specications. Otherwise you risk injuries and irreparable damages to the device.
Only connect so many identical devices that the maximum current consumption is not exceeded. Ensure the sucient dimensioning
(wire cross section) of the power cables used for all devices connected in series.
Safety instructions
12 AirBorne Pro Instrument
Wireless System

3 Features
The Wireless System AirBorne Pro Instrument Set consists of the following components:
nAirBorne Pro Instrument pedal receiver:
– Fixed built-in antenna for optimum reception quality
– Built-in chromatic tuner with easy-to-read LCD display
– Built-in magnetic charging station for the transmitter
– Cable tone simulator
– Mute function
– Four channels selectable
– Pairing and ID link LCD display
– Battery status LCD display
– Output: 1/4" phone socket
– Power supply: 9 V
– Robust metal housing
nAirBorne Pro Instrument pedal transmitter:
– Operation with built-in, rechargeable lithium-ion battery
– Easy to read LCD display
– Charging contacts for the receiver's magnetic charging station
– Mute function
– Battery status LCD display
– Pairing and ID link LCD display
– USB charger connection
Features
AirBorne Pro Instrument 13
Wireless System

– Rotatable 220° angled audio plug (1/4" jack plug)
nPlug-n-Play
nTransmission range up to 35 m
nUSB cable and 9 V plug-in power supply included
The system works in the frequency range 5.729 GHz… 5.820 GHz and is free of charge and reg‐
istration worldwide.
Features
14 AirBorne Pro Instrument
Wireless System

4 Installation and starting up
4.1 General Information
Unpack and check carefully there is no transportation damage before using the unit. Keep the
equipment packaging. To fully protect the product against vibration, dust and moisture during
transportation or storage use the original packaging or your own packaging material suitable
for transport or storage, respectively.
Create all connections while the device is o. Use the shortest possible high-quality cables for
all connections. Take care when running the cables to prevent tripping hazards.
nThis device utilizes frequencies that are not harmonized within the European Union (EU)
and therefore may only be used in certain EU member states. In all European countries, the
frequencies used for the transmission of audio signals are strictly regulated. Before you
start, make sure the frequencies are allowed in the respective country and check whether
the operation must be reported to the appropriate authority.
For more information, please visit: http://www.thomann.de.
nMake sure that transmitter and receiver are both tuned to the same channel.
nNever set multiple transmitters to the same channel.
nMake sure that there are no metal objects between the transmitter and receiver.
nAvoid interference from other radio or in-ear systems.
Notes on wireless transmission
Installation and starting up
AirBorne Pro Instrument 15
Wireless System

4.2 Dealing with lithium batteries
WARNING!
Incorrect handling of lithium batteries can result in injury
In the event of a short circuit, overheating or mechanical damage, lithium bat‐
teries can cause severe injuries.
Follow the advice on the correct handling of lithium batteries in the present sec‐
tion.
When handled correctly and appropriately lithium batteries pose no risk.
Store lithium batteries in a cool, dry place, ideally in the original packaging.
Store lithium batteries away from heat sources (e.g. radiators or sunlight). Lithium batteries are
hermetically sealed. Never attempt to open a lithium battery.
If the battery housing is damaged small amounts of the electrolyte may leak out. If this should
happen, seal the lithium battery in airtight packaging and wipe up the traces of electrolyte
using absorbent paper towels. You must wear protective rubber gloves when doing so. Clean
your hands and the aected surface thoroughly with cold water.
Never attempt to recharge non-rechargeable lithium batteries. When charging lithium bat‐
teries you must use a suitable charging device intended for the purpose.
Before disposing of the device remove the lithium batteries. Protect used lithium batteries
against potential short circuits, e.g. by covering the poles with adhesive tape.
Installation and starting up
16 AirBorne Pro Instrument
Wireless System

Only use powder extinguishers or other suitable extinguishing agents to extinguish a burning
lithium battery.
4.3 Receiver
NOTICE!
External power supply
The device is powered by an external power supply. Before connecting the
external power supply, ensure that the input voltage (AC outlet) matches the
voltage rating of the device and that the AC outlet is protected by a residual cur‐
rent circuit breaker. Failure to do so could result in damage to the device and pos‐
sibly the user.
Unplug the external power supply before electrical storms occur and when the
device is unused for long periods of time to reduce the risk of electric shock or
re.
First, connect the power adapter to the receiver and then plug the power adapter into the
power outlet. Then turn on the device with the main switch on the rear panel.
Connecting the power supply
Installation and starting up
AirBorne Pro Instrument 17
Wireless System

Connect the audio output of the receiver to your amplier. You can add further pedals (e.g.
eects pedal) between the receiver and amplier. The following gure shows an example of
how the device can be integrated into your signal chain.
CABLE TONE
'OX(UXTK6XU/TYZX[SKTZ'OX(UXTK6XU/TYZX[SKTZ
9 V
Connecting audio and starting
up
Installation and starting up
18 AirBorne Pro Instrument
Wireless System

5 Connections and controls
5.1 Receiver
CABLE TONE
'OX(UXTK6XU/TYZX[SKTZ9V
%
$
#
) * +
&
(
'
Connections and controls
AirBorne Pro Instrument 19
Wireless System

1 Display
2 Magnetic charging contacts for the transmitter
3 Footswitch to activate the tuner mode
Tuner mode can only be activated when transmitter and receiver are paired.
4[OUT] | 1/4" mm jack socket as unbalanced audio signal output for direct connection to an amplier
5 LED to indicate the coupling between transmitter and receiver.
If transmitter and receiver have not been successfully paired, the LED ashes orange. If the coupling is successful, the
LED turns o.
6 ID indicator | LED to indicate the selected channel (red = channel 1, green = channel 2, blue = channel 3, purple =
channel 4)
7[CABLE TONE] | rotary control for selecting a virtual cable length to simulate the inuences that a conventional cable
has on the transmission between the instrument and the amplier.
8 Main switch. Turns the device on and o.
9[DC IN] | connector for the supplied power adapter for power supply
10 [DC OUT] | connection to power an additional pedal
Connections and controls
20 AirBorne Pro Instrument
Wireless System