THORENS TD202 User manual

Thorens GmbH · Lus th eide85 · 51427 Bergisch Gladbach · De ut s ch land
www .thorens.com
[email protected]
1

Thorens GmbH · Lustheide 85 · 51427 Bergisch Gladbach · Deutschland
www.thorens.com
[e-mail]
2

THOR@!S
Thorens GmbH · Lustheide 85 · 51427 Bergisch Gladbach · Deutschland
www .thorens.com
[email protected]
3

FEATURES
TOP PANEL
THO~
Thorens GmbH · Lusthei de 85 · 51427 Bergisch Gladbach · Deutschland
www.thorens.com
[e-mail]
4

8 l-------+------1- --
THOR£N5
--
Thorens GmbH · Lustheide 85 · 51427 Bergisch Gladbach · Deutschland
www.thorens.com
[email protected]
5

1. Counterweight
The counterweight is used for precise adjustment of the stylus pressure on the vinyl, to properly
balance the tonearm.
2. Anti-Skating Control
To set the anti-skating force of the tonearm.
3. Tone arm Lever
Use this lever to lower and raise the tonearm.
4. Tone arm Lock (arm rest)
To lock the tone arm in place when not in use.
5.Headshell
This holds the needle in place and provide needle protection
6. START /STOP switch
To switch to "START" to start the playing or switch to " STOP " to stop the playing
7. Platter
Place the record here when playing.
8. Rubber Mat
Thorens Gm bH · Lustheide 85 ·51427 Bergisch Gladbach · Deutschland
www.thorens.com
[email protected]
6

THOR.@!!S
To provide floor protection, anti-slip safety and comfort
9. 33 / 45 RPM Switch
Select 33 or 45 rpm for playing a vinyl
Thorens GmbH · Lustheide 85 ·51427 Bergis ch Gladbach · Deutschland
www.thorens.com
[e-mail]
7

REAR PANEL
ED3
Thorens GmbH · Lustheide 85 ·51427 Bergisch Gladbach · Deutschland
www.thorens.com
[email protected]
8

THO~
10 Grounding terminal
A direct electrical connection to the earth
11. RCA JACKS selector
Plug in the RCA cable, and connect the cable to the audio amplifier
12 Pre Amp ON/OFF selector
ON: Connect the RCA cable to the LINE-IN terminal of the amplifier.
OFF: to stop the LINE-IN terminal of the amplifier.
13. USB Port
Use the USB cable to connect from your turntable to your computer.
14 Power Supply Jack
To connect the power cable for power supply
15 Power Switch
To turn the unit On/Off
Thorens GmbH · Lustheide 85 · 51427 Bergisch Gladbach · Deutschland
www.thorens.com
[email protected]
9

THO~
INITIAL STARTING UP
DUST COVER INSTALLATION
1) Unwrap the two hinges and the dustcover.
2) Note that the hinges have a clamp side and a tab side.
3) Note that the dustcover has two spots on its rear edge shaped to accept the clamps.
4) Carefully push the clamps onto the dustcover in these locations
5) Now snap the two clamps into the areas indicated atthe back of the turntable to accept them.
MOUNTAND ADJUST
1) Place the aluminum turntable platterover the center spindle. Place your fingers through one of
the access holes and grab the rubber belt and stretch it overthe motor pulley. Be sure the belt is not
twisted.
Spin the platter a few times to be sure the belt runs smoothly. Now place the rubber platter mat on
top of the platter so the ribbed sections point upward
2) Insert the headshell into the tone arm and fix it by turning the collar.
3) Insertthe counterweight on the end of the tone arm, rotating it until it threads into place.
Thorens GmbH · Lustheide 85 · 51427 Bergisch Gladbach · Deutschland
www.thorens.com
[email protected]
10