THORLABS CCS Series Instruction manual

Spectrometer
CCS Series Spectrometer
Quick Start Manual
2022

Version:
Date:
Item No.:
2.2
12-Dec-2022
M0009-510-422
Copyright © 2022 Thorlabs

Foreword
Contents 2
1 General Information 3
31.1 Safety 51.2 Ordering Codes and Accessories 51.3 Requirements
2 Installation 6
62.1 Parts List 72.2 Installing Software
3 Getting Started 9
4 Appendix 11
114.1 Certifications and Compliances 124.2 Return of Devices 124.3 Manufacturer/Importer Address 124.4 Warranty 124.5 Copyright and Exclusion of Liability 134.6 Thorlabs Worldwide Contacts

© 2022 Thorlabs
We aim to develop and produce the best solution for your application
in the field of optical measurement technique. To help us to live up to
your expectations and improve our products permanently we need
your ideas and suggestions. Therefore, please let us know about
possible criticism or ideas. We and our international partners are
looking forward to hearing from you.
Thorlabs GmbH
Warning
Sections marked by this symbol explain dangers that might result in
personal injury or death. Always read the associated information
carefully, before performing the indicated procedure.
Please read these advices carefully!
This manual also contains "NOTES" and "HINTS" written in this form.
Attention
Paragraphs preceded by this symbol explain hazards that could
damage the instrument and the connected equipment or may cause
loss of data.
Note
2

© 2022 Thorlabs
1 General Information
3
1 General Information
Thorlabs' fiber-based, compact, Czerny-Turner CCD spectrometers are available in three mod-
els. Two are sub-nanometer accuracy models that provide detection in the 350 - 700 nm
(CCS110x) or 500 - 1000 nm (CCS175x) range. The CCS200 offers a wide 200 - 1000 nm
spectral range with better than 2 nm accuracy. With the small footprint (122 mm x 79 mm x
29.5 mm), all units share features with larger, more expensive spectrometers such as the ability
to be synchronized via a TTL trigger input (up to 100 Hz) and to automatically compensate for
noise created by dark current.
The CCS Series Spectrometer is designed for general laboratory use. Integrated routines allow
averaging, smoothing, peak indexing, as well as saving and recalling data sets.
Application software OSA-SW
OSA-SW is an acronym for "Optical Spectrum Analyzer Software". This software acquires dir-
ect, transmittance and absorbance measurements in conjunction with Thorlabs' optical spec-
trum analyzers and CCD spectrometers.
Attention
Do not connect the CCS Series Spectrometer to a PC prior to installing the OSA-SW Applica-
tion! The installation package includes CCS Series Spectrometer specific drivers and software
that must be installed before the CCS Series Spectrometer is connected to the PC for the first
time.
After the installation, the software communicates with all Thorlabs CCD based CCS Series
Spectrometers and OSA20x Optical Spectrum Analyzers. Additionally, a number of virtual
devices are included to demonstrate the functionality of OSA-SW: five for OSA20x Analyzers
and one for CCS spectrometers.
1.1 Safety
Attention
The safety of any system incorporating the equipment is the responsibility of the assembler of
the system.
All statements regarding safety of operation and technical data in this instruction manual will
only apply when the unit is operated correctly as it was designed for.
The CCS Series Spectrometer must not be operated in explosion endangered environments!
Do not obstruct the air ventilation slots in the housing!
Do not remove covers!
Do not open the cabinet. There are no parts serviceable by the operator inside!
This precision device is only serviceable if properly packed into the complete original packaging
including the plastic foam sleeves. If necessary, ask for replacement packaging.
Refer servicing to qualified personnel!
Only with written consent from Thorlabs may changes to single components be made or com-
ponents not supplied by Thorlabs be used.

© 2022 Thorlabs4
CCS Series Spectrometer
Attention
The following statement applies to the products covered in this manual, unless otherwise
specified herein. The statement for other products will appear in the accompanying
documentation.
Note This equipment has been tested and found to comply with the limits for a Class A digital
device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference when the equipment is operated in a commercial envir-
onment. This equipment generates, uses, and can radiate radio frequency energy and, if not in-
stalled and used in accordance with the instruction manual, may cause harmful interference to
radio communications. Operation of this equipment in a residential area is likely to cause harm-
ful interference in which case the user will be required to correct the interference at his own ex-
pense.
Users that change or modify the product described in this manual in a way not expressly ap-
proved by Thorlabs (party responsible for compliance) could void the user’s authority to operate
the equipment.
Thorlabs is not responsible for any radio television interference caused by modifications of this
equipment or the substitution or attachment of connecting cables and equipment other than
those specified by Thorlabs. The correction of interference caused by such unauthorized
modification, substitution or attachment will be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all
optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Attention
Mobile telephones, cellular phones or other radio transmitters are not to be used within the
range of three meters of this unit since the electromagnetic field intensity may then exceed the
maximum allowed disturbance values according to IEC 61326-1.
This product has been tested and found to comply with the limits according to IEC 61326-1 for
using connection cables shorter than 3 meters (9.8 feet).

© 2022 Thorlabs
1 General Information
5
1.2 Ordering Codes and Accessories
Ordering code
Short description
CCS100(/M) 1
CCS spectrometer, 350 - 700 nm
CCS175(/M) 1
CCS spectrometer, 500 - 1000 nm
CCS200(/M) 1
CCS spectrometer, 200 - 1000nm
M14L01
1 m SMA MMF Patch Cable, 50µm / 0.22 NA (to CCS100 and
CCS175)
FG200UCC
1 m SMA MMF Patch cable, 200µm / 0.22 NA, High OH (to
CCS200)
CVH100; CVH100/M
Cuvette holder (imperial and metric versions)
1CCSxxx = imperial version, mounting holes 1/4-20;
CCSxxx/M = metric version, mounting holes M6x1
Attention
Make sure to use your CCS spectrometer only with the included fiber (see above table). If using
a different fiber, the Amplitude Correction Calibration will be affected!
1.3 Requirements
These are the requirements to the PC intended to be used for remote operation of the CCS
Series Spectrometer.
Minimum Requirements
·Operating System: Windows® 7 SP1, Windows®8, Windows®10, or Windows®11 (64 bit)
·Free USB 2.0 high speed port (Notice that a USB 1.1 port cannot be used)
·Processor: Intel Core i5™ or AMD Athlon II
·8.0 GB RAM
·.NET framework 4.7.2 or higher
·Monitor Resolution: 800 x 600 Pixel
Recommended Requirement
·Operating System: Windows® 11 (64 bit)
·Free USB 2.0 high speed port (Notice that a USB 1.1 port cannot be used)
·Processor: Intel™ Core i9 or AMD Athlon Ryzen
·16.0 GB RAM
·.NET framework 4.7.2 or higher
·Java Runtime 1.6 or higher
Note
An installer for .NET framework 4.7.2 is included in the full installer.
Please be aware that the OSA software requires a number of third party software installed on
your system. The installer checks for these software components and, if necessary, will install
them automatically. You will be notified accordingly.

© 2022 Thorlabs6
CCS Series Spectrometer
2 Installation
Attention
Do not connect the CCS Series Spectrometer to a PC prior to install the OSA-SW Application!
The installation package includes CCS Series Spectrometer specific drivers and software that
must be installed before the CCS Series Spectrometer is connected to the PC for the first time.
2.1 Parts List
Inspect the shipping container for damage. If the shipping container seems to be damaged,
keep it until you have inspected the contents and you have inspected the CCS Series
Spectrometer mechanically and electrically.
Verify that you have received the following items within the package:
1x
CCS Series Spectrometer
1x
This CCS Series Spectrometer Quick Reference
1x
USB 2.0 A-B mini cable, 1.5 meters
1x
Optical Fiber, SMA to SMA, 50µm / 0.22 NA, 1 meter (CCS100, CCS175)
Quartz Fiber, SMA to SMA, 200µm / 0.22 NA, 1 meter (CCS200)
1x
Trigger Input cable SMB to BNC
Attention
Make sure to use your CCS spectrometer only with the included fiber (see above table). If using
a different fiber, the Amplitude Correction Calibration will be affected.
CCS Spectrometer - Ports and Signal LEDs
(1)
USB port
(2)
Fiber input (SMA connector)
(3)
Status LED
(4)
Trigger Input (SMB connector)

© 2022 Thorlabs
2 Installation
7
2.2 Installing Software
Before installing OSA Software, please make sure that no CCS Series Spectrometer is connec-
ted. The OSA Software is available for download fromt he Thorlabs website.
Note
Please be aware that the OSA software requires a number of third party software installed on
your system. The installer checks for these software components and, if necessary, will install
them automatically. You will be notified accordingly.
Administrator privileges are required for installation. Please contact your system administrator if
you get an error message.
Installation steps are shown below in detail for an installation on a Windows 7©operating
system. After selecting "Install Software", the installer checks your system and determines the
software components that need to be installed.
Click "Install" to continue. The necessary software components (NI VISA) are being installed,
followed by installation of device driver software. The installation of all components is described
below.
Depending on the set up security level, the Installation Wizard might ask to allow to install the
driver software:

© 2022 Thorlabs8
CCS Series Spectrometer
To finalize the OSA Software installation, the computer must be restarted. Click "Finish" to re-
start and complete installation.

© 2022 Thorlabs
3 Getting Started
9
3 Getting Started
Attention
Do not connect the CCS Series Spectrometer to a PC prior to installing the OSA-SW Applica-
tion! The installation package includes CCS Series Spectrometer specific drivers and software
that must be installed before the CCS Series Spectrometer is connected the first time to the
PC.
The initial setup is simple to complete. Following installation of the software, connect the CCS
Series Spectrometer to a USB 2.0 port. The operating system recognizes the new hardware
and installs the firmware loader and the driver:
Then run the application software OSA-SW either from the desktop icon
1. Click to trace A and make sure that the topics below are checked.

© 2022 Thorlabs10
CCS Series Spectrometer
·Show
·Set as Active
·Write
2. Check that the connected spectrometer is recognized. If not, click to "Scan USB"
3. Apply an optical input signal to the fiber input. Increase the integration time until the spec-
trum is displayed. A right click into the data display area zooms in the intensity axis to it's
best fit to the spectrum.
Note
If you are using a CCS200 broadband spectrometer and a continuous spectrum (e.g. of a white
light lamp) shall be measured, please note the following recommendation:
Due to the eccentricity between the fiber core and the ferrule of the delivered FG200UCC MMF
and the geometry of the input slit of the spectrometer, the displayed spectral intensity may vary
when the SMA connector of the fiber is rotated within the input receptacle of the CCS200.
Please find the maximum intensity by rotation and then fix the fiber connector with the lock
bush. This ensures best measurement results.
Please see details about the OSA software features, handling and CCS Series Spectrometer
settings in the advanced user manual, provided with the data carrier. After the software has
been installed, it can be found as well in the folder
"All Programs - Thorlabs - Thorlabs OSA - CCS".

© 2022 Thorlabs
4 Appendix
11
4 Appendix
4.1 Certifications and Compliances

© 2022 Thorlabs12
CCS Series Spectrometer
4.2 Return of Devices
This precision device is only serviceable if returned and properly packed into the complete ori-
ginal packaging including the complete shipment plus the cardboard insert that holds the en-
closed devices. If necessary, ask for replacement packaging. Refer servicing to qualified per-
sonnel.
4.3 Manufacturer/Importer Address
Manufacturer Address Europe
Thorlabs GmbH
Münchner Weg 1
D-85232 Bergkirchen
Germany
Tel: [phone]
Fax: [phone]
www.thorlabs.de
Email: [email protected]
EU-Importer Address
Thorlabs GmbH
Münchner Weg 1
D-85232 Bergkirchen
Germany
Tel: [phone]
Fax: [phone]
www.thorlabs.de
Email: [email protected]
UK-Importer Address
Thorlabs, LTD.
204 Lancaster Way Business Park
Ely, CB6 3NX
UK
Tel: [phone]
Fax: [phone]
www.thorlabs.com
Email:
[email protected]
4.4 Warranty
Thorlabs warrants material and production of the CCS Series Spectrometer for a period of 24 months starting
with the date of shipment in accordance with and subject to the terms and conditions set forth in Thorlabs’ Gen-
eral Terms and Conditions of Sale which can be found at:
General Terms and Conditions:
https://www.thorlabs.com/Images/PDF/LG-PO-001_Thorlabs_terms_and_%20agreements.pdf
and
https://www.thorlabs.com/images/PDF/Terms%20and%20Conditions%20of%20Sales_Thorlabs-
GmbH_English.pdf
4.5 Copyright and Exclusion of Liability
Thorlabs has taken every possible care in preparing this document. We however assume no li-
ability for the content, completeness or quality of the information contained therein. The content
of this document is regularly updated and adapted to reflect the current status of the product.
All rights reserved. This document may not be reproduced, transmitted or translated to another
language, either as a whole or in parts, without the prior written permission of Thorlabs. Copy-
right © Thorlabs 2022. All rights reserved.
Please refer to the general terms and conditions linked under Warranty.

© 2022 Thorlabs
4 Appendix
13
4.6 Thorlabs Worldwide Contacts
For technical support or sales inquiries, please visit us at
https://www.thorlabs.com/locations.cfm for our most up-to-date contact information.
USA, Canada, and South America
Thorlabs, Inc.
[e-mail]
[e-mail]
UK and Ireland
Thorlabs Ltd.
[e-mail]
[e-mail]
Europe
Thorlabs GmbH
[e-mail]
Scandinavia
Thorlabs Sweden AB
[e-mail]
France
Thorlabs SAS
[e-mail]
Brazil
Thorlabs Vendas de Fotônicos Ltda.
[e-mail]
Japan
Thorlabs Japan, Inc.
[e-mail]
China
Thorlabs China
[e-mail]
Thorlabs 'End of Life' Policy (WEEE)
Thorlabs verifies our compliance with the WEEE (Waste Electrical and Electronic Equipment) direct-
ive of the European Community and the corresponding national laws. Accordingly, all end users in
the EC may return “end of life” Annex I category electrical and electronic equipment sold after
August 13, 2005 to Thorlabs, without incurring disposal charges. Eligible units are marked with the
crossed out “wheelie bin” logo (see right), were sold to and are currently owned by a company or in-
stitute within the EC, and are not dissembled or contaminated. Contact Thorlabs for more informa-
tion. Waste treatment is your own responsibility. “End of life” units must be returned to Thorlabs or
handed to a company specializing in waste recovery. Do not dispose of the unit in a litter bin or at a
public waste disposal site. It is the users responsibility to delete all private data stored on the device
prior to disposal.

www.thorlabs.com