THORLABS TXP5004 User manual

Thorlabs Instrumentation
TXP5004
Operation Manual
2017

Version:
Date:
Item No.:
3.1.5
31-Jan-2017
M0009-510-101
Copyright © 2017 Thorlabs GmbH

Foreword
Contents 2
1General Information 3
31.1 Safety
51.2 Ordering Codes and Accessories
51.3 Requirements
51.3.1 Hardware Requirements
51.3.2 Software Requirements
2Getting Started 6
62.1 Parts List
62.2 Installing Software
3Operating Elements TXP5004 10
4First Steps 11
114.1 USB driver installation
124.2 TXP Server configuration
154.3 Gateway Mode
5Operating Instruction 18
185.1 Installing and Removing Modules
6Maintenance and Service 19
206.1 Replacing the Line Fuse
206.2 Replacing the Internal Fuses
216.3 Troubleshooting
7 Appendix 23
237.1 Technical Data
247.2 Certifications and Compliances
257.3 Warranty
267.4 Copyright and Exclusion of Reliability
277.5 Thorlabs 'End of Life' Policy
287.6 Thorlabs Worldwide Contacts

© 2017 Thorlabs GmbH
We aim to develop and produce the best solution for your application
in the field of optical measurement technique. To help us to live up to
your expectations and improve our products permanently we need
your ideas and suggestions. Therefore, please let us know about
possible criticism or ideas. We and our international partners are
looking forward to hearing from you.
Thorlabs GmbH
Warning
Sections marked by this symbol explain dangers that might result in
personal injury or death. Always read the associated information
carefully, before performing the indicated procedure.
Please read these advices carefully!
This manual also contains "NOTES" and "HINTS" written in this form.
Attention
Paragraphs preceeded by this symbol explain hazards that could
damage the instrument and the connected equipment or may cause
loss of data.
Note
2

© 2017 Thorlabs GmbH
1 General Information
3
1 General Information
The TXP5004 4 channel Test an Measurement Platform chassis is designed to accommodate
up to 4 TXP modules. These modules are controlled by an external PC, connected via the USB
interface of the TXP5004. It has a wide range power supply compatible with line voltages
between 100...240VAC, 50-60Hz.
The TXP software allows to use the control PC as a gateway to a local area network so that the
TXP modules can then be controlled remotely via the LAN and the local USB control PC.
·Small footprint with 4module slots
·Hosts any TXP Series module
·Intelligent modules - memory / processor capacity where needed (real time apps)
·Configurable module pooling for complex measurement solutions
·Programming Interface
USB interface with LabVIEW®/ LabWindows/CVI® and C drivers
Enhanced macro function capabilities
·Remote control or support via USB connection
·Ethernet remote control possible via a gateway PC
1.1 Safety
Attention
All statements regarding safety of operation and technical data in this instruction manual
will only apply when the unit is operated correctly as it was designed for.
Prior to applying power to the TXP5004, make sure that the protective conductor of the 3
conductor mains power cord is correctly connected to the protective earth ground
contact of the socket outlet! Improper grounding can cause electric shock with damages
to your health or even death!
All modules must only be operated with proper shielded connection cables.
The TXP5004 must not be operated in explosion endangered environments!
Do not remove covers! Do not obstruct the air ventilation slots in the housing!
Do not open the cabinet, there are no parts serviceable by the operator inside!
Refer servicing to qualified personnel!
Only with written consent from Thorlabs GmbH may changes to single components be
made or components not supplied by Thorlabs GmbH be used.
This precision device is only serviceable if properly packed into the complete original
packaging. If necessary, ask for a replacement package prior to return.
Attention
The following statement applies to the products covered in this manual, unless
otherwise specified herein. The statement for other products will appear in the
accompanying documentation.
This equipment has been tested and found to comply with the limits for a Class Adigital
device, pursuant to part 15 of the FCC Rules and meets all requirements of the Canadian
Interference-Causing Equipment Standard ICES-003 for digital apparatus. These limits
are designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.

© 2017 Thorlabs GmbH4
TXP5004
Operation of this equipment in a residential area is likely to cause harmful interference in
which case the user will be required to correct the interference at his own expense.
Thorlabs GmbH is not responsible for any radio television interference caused by
modifications of this equipment or the substitution or attachment of connecting cables
and equipment other than those specified by Thorlabs GmbH. The correction of
interference caused by such unauthorized modification, substitution or attachment will
be the responsibility of the user.
The use of shielded I/O cables is required when connecting this equipment to any and all
optional peripheral or host devices. Failure to do so may violate FCC and ICES rules.
Attention
Mobile telephones, cellular phones or other radio transmitters are not to be used within
the range of three meters of this unit since the electromagnetic field intensity may then
exceed the maximum allowed disturbance values according to IEC 61326-1.
This product has been tested and found to comply with the limits according to
IEC 61326-1 for using connection cables shorter than 3 meters (9.8 feet).

© 2017 Thorlabs GmbH
1 General Information
5
1.2 Ordering Codes and Accessories
Ordering code:
TXP5004 4 Channel USB T&M Mainframe
Accessories:
TXP5000C Blind module to cover empty module slots (for TXP5004 and TXP5016)
1.3 Requirements
These are the requirements to the PC intended to be used for remote operation of the
TXP5004.
1.3.1 Hardware Requirements
CPU: 1 GHz or higher
RAM: 256 MB
Graphic card Min. 32 MB memory
Hard disc Min 100 MB free storage space
Interface Free USB2.0 port, USB cable according the USB 2.0 specification
1.3.2 Software Requirements
The TXP5004 software is compatible with the following operating systems:
·Windows®7 (32-bit, 64-bit)
·Windows®8.x (32-bit, 64-bit)
For operation of the TXP5004, also an NI-VISA (version 5.4.1 or higher) is required. This NI-
VISA engines comes with the Thorlabs GmbH TXP5004 installation software package, but can
be downloaded also from National Instruments' website www.ni.com.

© 2017 Thorlabs GmbH6
TXP5004
2 Getting Started
2.1 Parts List
Inspect the shipping container for damage.
If the shipping container seems to be damaged, keep it until you have inspected the contents
and you have inspected the TXP5004 mechanically and electrically.
Verify that you have received the following items within the package:
TXP5004
1. 4 Slot Chassis with USB Control
2. Front Cover Plates TXP5000C for all unused slots
3. USB A to B Cable (TXPCABUSB)
4. Operation Manual
5. Power Cord
2.2 Installing Software
Note
Do not connect the TXP5004 to the PC prior to software installation!
Attention
Exit all running applications on your PC as the installer may require a reboot of your PC
during installation!
The TXP software package contains:
·NI VISA Runtime 5.4.1
·USB Drivers for TXP5001AD and TXP5004 and module slots
·Control software for TXP modules
·TXP Administration Tools
Below the software installation to a Windows 7®64 bit operating system is described.
Download the ZIP archive from our website:
https://www.thorlabs.com/software_pages/ViewSoftwarePage.cfm?Code=TXP5000
and unpack the archive. Then execute the setup.exe:

© 2017 Thorlabs GmbH
2 Getting Started
7
A user account control warning comes up:
Allow the installation. Then follow the the screenshots below:

© 2017 Thorlabs GmbH8
TXP5004