Tiger Tool 10910 User manual

1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
CAUTION: USE REPLACEMENT PARTS AND ACCESSORIES PROVIDED BY TIGER TOOL ONLY. ALL REPLACEMENT PARTS AND ACCESSORIES ARE
AVAILABLE. KEEP HYDRAULIC COUPLER PROTECTED WHEN NOT IN USE. DUST CAPS SHOULD BE USED ON COUPLERS WHEN NOT IN USE TO
AVOID CONTAMINANTS FROM ENTERING THE HYDRAULIC CYLINDER AND POWER SOURCE.
THIS PRACTICE WILL HELP TO EXTEND THE LIFE OF THIS PRODUCT AND ENSURE CONTINUED CONSISTENT OPERATION.
Safety Warning
Read all instructions and safety warnings prior to operation. Failure to do so could result in
equipment damage, personal injury or even death.
•
Stay Alert! Watch what you are doing and use common sense when
operating this tool.
•
Inspect product for damage prior to using; do not use if product is
in unsafe condition.
•Do not operate tool while under the influence of drugs, alcohol
or medication.
•
Always use safety equipment to prevent injuries. Approved face and
eye protection must always be worn by the operator, as well as others
in the work area.
•
Do not overreach. Keep proper footing and balance at all times.
•
Dress properly. Do not wear loose clothing or jewelry.
Keep your hair, clothing and gloves away from moving parts.
•
Keep hands clear of all pressurized hydraulic components.
•
Always ensure hoses are free from sharp bends and kinks.
• Keep your work area clean and well lit.
•Cylinders are designed for 10,000 psi (700 bar) maximum working
pressure. Do not connect to a pump with a higher rated pressure.
Use a pressure gauge in the system at all times. Ensure all components
in the system are rated for 10,000 psi (700 bar).
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder

D
1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Operating Instructions
Have What It Takes
A
B
C
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder
Race Removal
CAUTION: Always follow Manufacturers recommendations
when servicing bearing races.
1 Choose the corresponding adapter kit required for the
bearing set/race number.
(Figure D)
2 Place the spit ring over the tapered disk wedge (tapered
faces together).
(Figure A)
3 Place the clamp plate on top of the split ring and
disk wedge assembly and finger-tighten the supplied
hex flange screws.
4 Insert the clamp assembly into the hub with the heads of
the flanged hex screws facing the direction the race is to
be pulled.
(Figure B)
5 Align the groove in the split ring with the minor diameter
of the race.
6 Using a helper if required and the handle on the back-end
for support, apply torque to the two hex flanged screws –
alternating the applied force between the screws until the
clamp plate and disk wedge have come into contact.
(Figure C)
The 10910 Hydraulic Bearing Race Starter Kit
combines with your previously purchased 17202
Hydraulic Cylinder.

1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Operating Instructions
Have What It Takes
Race Removal Continued
CAUTION: Always follow Manufacturers recommendations
when servicing bearing races.
7 Insert the long length of threaded rod into the clamp disk
assembly and thread into place until the rod bottoms-out
on the aluminum handle in the back of
the disk assembly.
(Figure E)
8 Thread the hat supplied onto the 20T
hydraulic cylinder.
(Figure F)
9 Slide the hydraulic cylinder and hat assembly onto the
threaded rod being careful to align the cut outs on the hat
with the axle studs on the hub.
(Figure G)
10 Install the supplied washer and nut on the end of the
hydraulic cylinder assembly – thread the nut all the way
such that the washer is tightly sandwiched between the nut
and the piston on the cylinder.
11 Using a 10,000psi hydraulic pump, actuate the cylinder
until the bearing race is free from the hub.
12 Pull the whole assembly out of the hub and disassemble
the components.
(Figure H)
E
F
G
H
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder

Operating Instructions
Race Installation
CAUTION: Always follow Manufacturers recommendations
when servicing bearing races.
1Thoroughly clean the hub and remove any burrs from the
race seat.
2Lay the wheel/tire assembly on its side and position the
new race in the hub with the corresponding install adapter
on to the race.
(Figure A)
3Using a hammer tap the install plate evenly around the outer
perimeter to get the race started parallel to the seat.
4Remove the install plate and lift the wheel/tire assembly
upright.
5Insert the threaded rod into the install adapter with a
supplied washer and nut against the flat side of the install
plate.
6Insert the rod and install adapter through the hub
with the tapered side of the adapter to the tapered
side of the race.
(Figure B)
7Place the hydraulic cylinder and hat over the threaded rod
and install supplied washer and nut hand tight.
A
B
1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder

Operating Instructions
Race Installation Continued
CAUTION: Always follow Manufacturers recommendations
when servicing bearing races.
8Make sure the assembly is centered on the hub.
(Figure C)
9Using a 10,000psi hydraulic pump, apply force until the
race is seated (approximately 4,000 -5,000 psi).
9A Make sure the race is being pulled parallel to the
race seat, minor adjustments may be required with a
hammer while installing).
(Figure D)
10 Release the hydraulic pressure and disassemble
the tool.
11 Take care of oil all parts and return to the tool box
supplied. Proper maintenance of parts ensures a
long lifetime.
Here at Tiger Tool, your satisfaction is our number one
priority. Should you have any questions about this or any
of our products, please call us at 1.800.661.4661.
D
1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
C
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder

Item No.
1
2
3
4
5
6
7
8
9
10
Part Number
10908-7
10909-7
10908-2
10908-4
10908-6
15001-40B
15001-41
15001-42
10908-9
10908-10
Qty.
1
1
1
1
1
1
2
2
4
2
Description
Spacer Ring
Hat
Clamp B Plate
Clamp A Plate
Clamp C Plate
Threaded Rod
Hex Nut
Washer
⅜" - 16 Hex Flange Screw
⁵/₁₆" - 18 Hex Flange Screw
Parts Breakdown
1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
1
4
5
2
3
7
8
9
10
6
Have What It Takes
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder

Item No.
11
12
13
14
15
16
17
18
19
Part Number
10909-9
10909-6
10909-4
10909-5
17202-13
10909-3
10909-2
10909-8
10909-1
Qty.
1
1
1
1
4
1
1
2
1
Description
45º Elbow
4"Handle
2 ¾"Handle
3.625" Handle
3/8-16 x ½" SHCS
4.813" Disk Wedge
3.938" Disk Wedge
¼-20 X ½" SHCS
2.9375" Disk Wedge
Parts Breakdown
1.800.661.4661
View demonstration videos and a
complete product list at tigertool.com
Technical Support
Have What It Takes
10910
Hydraulic Bearing Race Starter
Kit w/o Cylinder
12
14
15
17
13
16
18
19
11