Tiiwee X1 User manual

USA - ENGLISH

Tiiwee X1 Alarm Kits

1. Disclaimer

2. Introduction

3. System overview

4. Installing your Tiiwee alarm system in four simple steps

5. Daily use of your alarm system

6. Expanding your system

Connecting additional door sensors

Connecting PIR motion detectors

Connecting remote controls

Adding additional sirens to your system

7. Deleting accessories or changing the zones

Clearing all sensors from a zone. Reconnecting a sensor to a zone.

Disconnecting remote controls

8. Battery lifetime, and low battery voltage

9. Replacing batteries

10. Resetting the X1-siren to factory settings

11. tiiwee window sensor 03

12. tiiwee PIR sensor 02

13. Customer service

14. Warranty and liability

15. FCC regulation

1. Disclaimer

Testing

It is recommended that the alarm is tested immediately after installation and at regular intervals not

exceeding one month. Note: a cloth can be used to cover the siren and reduce the sound output of

the alarm during testing.

Warning

Risk of personal injury: prolonged exposure to the alarm siren may cause permanent hearing loss. For

indoor use only. Do not use in wet locations.

Limitations of alarm products

Test product regularly to ensure it functions in accordance with these instructions. Tiiwee B.V. is not

providing insurance or any guarantee that the risk of burglary or robbery will be reduced or

prevented even if this product is used properly. Tiiwee B.V. recommends that users obtain proper

insurance coverage for these risks. Tiiwee B.V. does not represent or warrant that this product may

not be compromised or circumvented, that it will provide proper or adequate warning, or that the

use of this product will prevent injury, property damage or other losses. Note that this product may

be bypassed, compromised, fail or fail to warn like any alarm, including due to improper installation,

positioning, or maintenance, tampering; dead, faulty, or improperly installed batteries; sensing

limitations and component failures.

Audible alarm signals may be outside of hearing range, muted by doors, walls and floors, unheard by

deep sleepers or the hearing-impaired, or overwhelmed by other sounds.

Battery Warning

Caution: Batteries may leak harmful liquids or ignitable materials or explode causing injury and

product damage.

•Do not mix old and new batteries or other battery types

•Replace all batteries at the same time

•Replace fully discharged batteries immediately

2. Introduction

Congratulations with your new X1 Tiiwee Alarm Kit. The Tiiwee Alarm Kit is a versatile alarm system

that detects if people or animals are entering your home or shop. It allows you to use several sensors

with one or more alarms in up to four different zones. These sensors (PIR Motion Sensors,

Window/Door sensors) connect wirelessly to an alarm unit ("X1-siren"). This alarm unit produces a

doorbell-sound or a very loud siren. The alarm unit can be placed on a fixed position or taken with

you as you move around the house or if you go to sleep.

A maximum of 10 sensors can be connected to each zone. Also, up to 10 remote controls can be

paired with each alarm unit. A sensor or remote control can be paired to several Alarm units if

required.

Intended use

The Tiiwee Home Alarm System is primarily designed to deter burglars when they enter your home.

The heart of the system is the X1-siren. Place the siren in your home where burglars are most likely

to enter. If you have a larger home, please consider placing additional Tiiwee X1 or A3 (outdoors-)

sirens.

The system is ready for use. Your system is pre-configured, and the sensors and remote controls are

connected to the X1-siren. Window sensors are connected to zone 1. If a PIR motion sensor is

included, it is connected to zone 2. We advise reading this user manual carefully and to familiarize

yourself with its operating principle and ways to fine-tune it to your exact needs.

3. System overview

Connect-button

Siren

Zone indication

tiiwee remote control 03

Technical Specifications

Trade name: tiiwee remote control 03

Model Number: TWRC03

FCC ID: 2BAP8TWRC03

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

Deactivation-button: Deactivates the

alarm unit

Loudspeaker-button: Changes the

notification sound from the siren

Activation-button:

activates the alarm unit

Emergency-button: triggers a

loud alarm sound. Press the

Deactivation-button to stop

•Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

4. Installing Your Tiiwee alarm system in four simple steps

1. Unpack: Unpack all kit components and lay them in front of you on the table.

2. Remove battery protection:

X1-siren:Slide the back panel from the X1-siren and remove the battery protection strip. You

hear one beep, and the X1-siren switches on automatically.

Door sensors: Remove the battery protection strip at the back of the sensor by pulling it.

Motion detector (if included): Open the battery compartment, and remove the battery

protection strip

3. Familiarize Yourself with Your System:

a. Arrange the door sensors such that the magnet is on the right-hand side of each sensor. The

triangles on the middle of the sides of the sensor and the magnet cannot be more than 5 mm

apart. IMPORTANT: Position them so that the triangles are facing each other.

Position the motion detector with the detection window facing downwards to avoid that it

detects anything for the moment.

Use the Loudspeaker-button on the remote control to switch from the doorbell-sound (2

different volumes) to siren sound. Cover the siren to avoid damaging your hearing. Press the

Loudspeaker-button of the remote control until you hear the doorbell-sound ("Ding-Dong").

b. Press the Activation-button ( ) on the remote control to arm the X1-siren. You hear a

short beep accompanied by one brief flash of the LEDs.

c. Now move the magnet away from the first sensor. You hear the

doorbell-sound (“Ding-Dong”), and the red light on the sensor

lights up. Repeat this procedure for all other door sensors.

Motion detector (PIR kits only): Slowly, in front of the motion detector, wave your hand at a

distance of approximately 50-70 centimetres. You hear a doorbell-sound, and the detection

window of the sensor lights up.

4. Installing your system

Deactivate the X1-siren using the Deactivation-button on the remote control ( ). Now,

mount the X1-siren and door sensors following the instructions in the manual.

How to mount the X1-siren

First, attach the back panel to the wall using the self-adhesive pads or screws (included).

Place the X1-siren on the back panel and attach it to the back panel with the smallest screw

at the bottom.

Once all components are mounted, activate the system: Select the Loudspeaker-button on

the remote control to choose the loud siren sound. Now, to activate your system, press the

Activation-button.

5. Daily use of your alarm system

Switch On/Off

Press the On/Off-button on the X1-siren for 5 seconds to switch the unit on or off. When switching

on, you hear one short beep and the LEDs light-up from top to bottom. When switching the X1-siren

off, you hear one long beep sound, and the LEDs dim from the bottom to the top. When the X1-siren

is switched on, it will be in the same state (active or deactivated) as it was when it was switched off.

Activating the system

On the X1-siren: short press the CONNECT-button. On the remote control: press the Activation-

button.

You hear one beep as a confirmation that the system is activated.

Deactivating the system

X1-siren: short press the CONNECT-button.

Remote control: press the Deactivation-button.

Deactivating the system will be confirmed by two beeps.

Indicator light: Activated status

The X1-siren features an indicator light that shows if the system is active or not. When the system is

activated, the LED of zone 4 flashes every 5 seconds. To switch off the indicator light, while in

activated mode, press the CONNECT-button for 5 seconds. You hear one beep, and the indicator light

switches off. To switch on the indicator light again, repeat the above-described procedure.

Choosing doorbell-sound or siren sound

In deactivated mode, short press the On/Off-button on the X1-siren or the Loudspeaker-button on

the remote control to switch between doorbell-sounds and siren sound. The order of the sounds is

1. loud doorbell

2. mild doorbell

3. very loud siren (120dB)

You hear a short fragment of the selected notification sound or alarm sound each time you press the-

button.

IMPORTANT: Changes to the X1-siren settings can only be performed when the X1-siren is in

deactivated mode. If you try to make changes to the X1-siren while the system is in the activated mode,

you hear three beeps.

As a general rule, three beeps always means that the X1-siren is not able to process the input. Consult

the instructions for use in such case.

When the siren alarm sounds

When a sensor triggers an alarm in siren mode, the alarm sounds for 2 minutes. Then, the siren stops

and the X1-siren returns into activated mode again automatically. The siren can also be stopped at

any time with the remote control. During an alarm, the LED of the respective zone lights up until the

alarm is switched off.

Stopping an alarm

There are two ways to stop the alarm when the siren sounds. Stop the siren by pressing the

Deactivation-button on the remote control.

Alternatively, you can also stop the alarm on the X1-siren by the following-button combination: Press

3 times quickly the On/Off-button followed immediately by a quick press of the CONNECT-button.

6. Expanding your system

Expand the X1 system with Tiiwee door sensors and motion detectors from the Tiiwee Home Alarm

System. It is possible to add up to 10 Sensors per zone. Up to 10 remote controls can be connected.

Furthermore, additional X1-siren units, as well as A3 outdoor sirens, can be connected by combining

the existing sensors to the new sirens.

IMPORTANT: Warranty

Please only use accessories from the Tiiwee Home Alarm System to ensure a proper function of the

system.

Connecting additional door sensors

This is an example of connecting a door sensor to zone 2:

•De-activate the X1-siren by pressing the CONNECT-button on the X1-siren or the

Deactivation-button on the remote control.

•On the X1-siren, press the CONNECT-button for 5 seconds. You hear a beep and all four LEDs

light up.

•On the X1-siren, press the CONNECT-button short two times to select zone 2. The LED of

zone 2 lights up.

•Activate the door sensor by moving the magnet away from the sensor. You hear two beeps,

and the LED of zone 2 blinks twice.

•Save the setting by pressing the On/Off-button on the X1-siren briefly.

The door sensor is now connected to zone 2.

Connecting PIR motion detectors

Proceed as described with the door sensors in the previous chapter. Trigger the device by moving

your hand in front of the motion detector at a distance of 50-70 cm. When performing the pairing

procedure, make sure the motion detector is facing downwards from you to avoid unwanted signals

from the device while pairing it to the X1-siren.

Connecting remote controls

Up to 10 remote controls can be connected to the X1-siren.

Pairing remote controls

▪Press the CONNECT-button for 5 seconds. You will hear a beep and all four LEDs light up

▪Press one (any)-button on the remote control(s) which you wish to connect. You will hear two

beeps for confirmation of correct pairing.

▪Press the On/Off-button shortly to store the settings

The remote control is now connected to the X1-siren.

Adding additional sirens to your system

The system can be expanded with more X1-sirens and A3-outdoor sirens. Just connect your sensors

and remote controls to the new X1 or A3 siren. A new siren operates independently of existing

sirens.

Please refer to the below image which outlines the principle.

7. Deleting accessories or changing the zones

Clearing all sensors from a zone. Reconnecting sensor to a zone.

Sensors can be deleted from a zone by deleting all connection information for a zone. Any sensors

that you would like to keep in that zone will need to be reconnected to that zone again.

In the following example procedure, all sensors from a zone are deleted and reconnected to the new

zone(s).

Below is an example for deleting the door sensor from zone 3 and connecting this door sensor to

zone 1:

Deleting zone information

oDeactivate the X1-siren by pressing the CONNECT-button on the X1-siren or the Deactivation-

button on the remote control.

oDeleting all sensors from zone 3:

▪On the X1-siren, press the CONNECT-button for 5 seconds. You hear a beep and all four LEDs

light up

▪On the X1-siren, press the CONNECT-button short three times to select zone 3. The LED of

zone 3 lights up.

▪On the X1-siren, press the CONNECT-button for 5 seconds. This will delete all sensors from

zone 3. You hear four beeps to confirm, and the LED blinks four times.

Now, connect the door sensor to zone 1:

▪On the X1-siren, press the CONNECT-button for 5 seconds. You hear a beep and all four LEDs

light up

▪On the X1-siren, press the CONNECT-button short 1 once to select zone 1. The LED of zone 1

lights up.

▪Activate the door sensor by removing the magnet away from the sensor. You hear two

beeps, and the LED of zone 1 blinks twice.

▪On the X1-siren, save the setting by pressing the On/Off-button briefly.

The door sensor has now been removed from zone 3 and reconnected to zone 1.

Disconnecting remote controls

IMPORTANT: With this procedure, you disconnect all remote controls. Please reconnect the remote

controls if you wish to operate the X1-siren through one or more remote controls.

oDeactivate the X1-siren by pressing the CONNECT-button on the X1-siren or the Deactivation-

button on the remote control.

▪On the X1-siren, press the CONNECT-button for 5 seconds. You hear a beep and all four LEDs

light up

▪On the X1-siren, press the CONNECT-button again for 5 seconds. You will hear four beeps and

all the LEDs quickly blink four times.

▪On the X1-siren, short press the On/Off-button to save the new settings.

All remote controls are now disconnected from the X1-siren. To reconnect a remote control, please

consult the chapter “Expanding your system – connecting remote controls”.

8. Battery lifetime, and low battery voltage

The expected battery lifetime of all system components is 10-12 months under normal conditions.

We recommend to check the batteries regularly and to replace them at least once a year. Please

always use alkaline batteries.

Replace batteries when you notice the following:

X1-siren:You hear 3 beeps every 20 seconds.

Door sensors: The red LED light of the sensor is blinking or is continuous lit.

PIR motion sensors: The indicator light in the front lights up continuously.

PIR motion sensors: When the indicator light has been switched off manually, the low battery

indication will not active. In this case, check the correct operation of the motion sensor at regular

intervals.

9. Replacing batteries

Remote control: Remove the 3 screws on the back of the remote control. Open the remote control.

Now, using a pin, nail or small screwdriver, lift the electronic board at the notch. This will give you

access to the battery. Gently remove the battery from its compartment by pushing it sideways. The

battery type is CR2032 (3V, Lithium battery). Please also refer to the image below:

X1-siren:Remove the screw at the bottom of the back panel. Now, slide off the back panel and

replace the batteries with 3x AA size 1.5V alkaline batteries.

Door sensors:

▪Remove the screw at the bottom of the sensor. Now slide the sensor upwards and remove it

from the back panel.

▪Take out the old battery and replace it with a fresh AAA alkaline battery - please note the

correct polarity.

▪Slide the sensor on the back panel and secure it with the screw at the bottom of the sensor.

PIR Motion detectors: Slide off the back panel and replace the batteries with 2 x AAA or 3x AAA

batteries depending on the model.

IMPORTANT: DO NOT USE RECHARGEABLE BATTERIES UNDER ANY CIRCUMSTANCES

10.Resetting the X1-siren to factory settings

This procedure erases all information which is related to sensors and remote controls.

▪Take out one battery from the X1-siren.

▪While keeping the CONNECT-button pressed, re-insert the battery.

▪After a few seconds, you hear 10 beeps with longer intervals followed by another 10 beeps

with shorter intervals.

▪Now, release the CONNECT-button.

▪Now, the X1-siren restarts automatically.

Your X1-siren now has been reset to factory settings. You can reconnect your remote controls and

sensors.

11. tiiwee window sensor 03

IMPORTANT: Please assure that the distance between magnet and sensor does not exceed 5 mm.

The triangles on the door sensor and the magnet are alignment aids. They must face each other at

a distance of a maximum of 5 mm for the door sensor to work optimally.

Product Overview and Operation

The door sensor consists of a magnet and a sensor which contains a detector for changes in magnetic

fields (‘flux’). When the magnet is moved away from the sensor, the sensor will detect that motion

and will send a wireless signal to the Tiiwee Alarm unit. The Tiiwee Alarm unit will now emit a

powerful alarm sound or a doorbell-sound (“Ding-Dong”) depending on the settings of the Alarm

unit.

Magnet

Triangle mark

Sensor

Triangle mark

The instructions for pairing additional door sensors with the Tiiwee alarm system are included in this

manual, or can be found on our website www.tiiwee.com or one of our Youtube channels.

Installation of Door sensors

General guidelines:

•Do not install the sensor near magnets or magnetic devices - this may cause the alarm to be

activated accidentally.

•Clean all surfaces carefully before installation.

•The magnet and sensor should be placed on the door and door frame respectively. The principle

of the system is that an alarm is triggered when the sensor and magnet are separated because the

window or door is opened.

•If possible, mount the sensor on the door frame and not on the door or window itself. This

position reduces the wear and tear that occurs when windows and doors are closed (shocks). It

increases the service life of your sensors.

Installation examples

Various installation examples are shown on the first page of this manual. Make sure that both the

installation surfaces are clean and free from grease and dust. It is essential to respect the maximum

distance of 5 mm between sensor and magnet. Also, please assure that the triangle marks are

aligned.

How to mount a door sensor (please see the inside of the front page)

Image 1: Door and doorpost are at the same level. Position the sensor and magnet next to each other

and position the triangle markers on the sides of the magnet and sensor as such that they are close

to one another.

Image 2: The door is protruding relative to the doorpost. Mount the magnet sideways on the top of

the door and position the sensor with a few millimetres distance on the doorpost and position the

triangle markers on the sides of the magnet and sensor as such that they are close to one another.

Image 3: The doorpost is protruding relative to the door. Mount the sensor sideways on the doorpost

and then position the magnet on the door with a few millimetres distance and position the triangle

markers on the sides of the magnet and sensor as such that they are close to one another.

IMPORTANT - PLEASE NOTE:

•It is essential that the sensor and magnet are aligned correctly and are at the same level using

the triangle marks.

•The distance between the sensor and the magnet should not exceed 5mm.

Magnet:

•Installation with screws: remove the back panel from the magnet by sliding it off. Then, position

the back panel at the desired position. Now, after the magnet back panel has been mounted, put

the magnet on the back panel and slide it downwards until it is in its final position.

•Installation with double-sided tape: peel off the protective foil from one side and stick the tape

onto the magnet. Then, peel off the other part of the protective foil and stick the magnet onto the

door or doorpost.

Sensor:

Before installing the sensor, please assure that both the magnet and sensor will be aligned as

described in the chapter “How to mount a door sensor”.

•Sideways installation and installation with double-sided tape: Peel off the protective foil from one

side of the tape and stick the tape onto the sensor. Then, peel off the other part of the protective

foil and stick the sensor onto the door or doorpost.

•Installation with screws: Remove the screw at the bottom of the sensor. Now slide the sensor

upwards and remove it from the back panel. Then, position the back panel at the desired position.

Now, place the sensor on the back panel and slide it downwards. Secure the sensor with the screw

at the bottom of the sensor.

Test your door sensor

1. After the installation, open the window or door.

2. The red indicator light on the front of the sensor will flash once.

3. The sensor is now correctly setup.

Technical Specifications

Trade name: tiiwee window sensor 03

Model Number: TWWS03

FCC ID: 2BAP8TWWS03

Transmission Distance: 100m (Open Area)

Transmission Frequency: 433MHz

Operating Voltage: 1,5V

Sensor Size: 78×24×18mm

Magnet Size: 75×10×12mm

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this

device may not cause harmful interference, and (2) this device must accept any interference received, including

interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance could void

the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to

Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference in a residential installation. This equipment generates, uses and can radiate radio frequency

energy and, if not installed and used in accordance with the instructions, may cause harmful interference to

radio communications. However, there is no guarantee that interference will not occur in a particular

installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by

turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of

the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This

equipment should be installed and operated with minimum distance 20cm between the radiator and your

body. This transmitter must not be co-located or operating in conjunction with any other antenna or

transmitter.

12. tiiwee PIR sensor 02

Product Overview and activation

Open the back panel to insert the batteries. Please note the correct polarity. Now, close the back

panel again. Slide the ball joint in place until it locks. Do not yet position the wall mount. Please first

carefully read the sections “General installation guidelines” and “How to mount a PIR motion

sensor” before you install the motion detector.

General installation guidelines

Avoid positions close to a window, air conditioners, fluorescent lights, heaters, refrigerators, stoves,

and direct sunlight and other places where the temperature would change rapidly, and where airflow

is high. If there are two detectors in the same detecting range, please adjust the position to avoid

interference and false alarms.

IMPORTANT: The Infrared detector is sensitive to a human’s horizontal movement. The detector is

less susceptible to vertical movements. Therefore, it is advised to aim the device at a 90 degrees’

angle to a person’s walking direction.

How to mount a PIR motion sensor

Unlike magnetic door and window sensors, PIR motion sensors recognize heat differences.

Sometimes heat differences are unnoticeable. Our PIR motion sensors feature advanced algorithms

that help to detect the difference between a human being and environmental heat changes.

However, it is essential to carefully select the right position of PIR motion sensors for it to function

correctly.

Therefore, we recommend installing the motion detector in a corner that is void from any of those

factors mentioned above, and where the sensor is directed at the room you want to guard.

Detector window

Indicator light

On/Off switch

Micro USB port

Wall mount plate

Final installation: Taking the above in consideration, use the adhesive tape or the screws to attach

the wall mount to the wall. Now, attach the detector to the wall mount, and change the detecting

angle and distance by adjusting the installation height and the bracket. It is advised to install the

device at a height of approximately 2 meters.

Test

1. After the installation, turn the switch to ON. Now, walk or move in front of the PIR sensor at a

distance between 3 and 6 meters.

2. The Indicator light should light up once. Note the 5 seconds delay between 2 signals. The delay is

normal and intentional to save battery power.

3. If needed, adjust the detector angle to get the desired detection range.

When the detector indicator flashes

•LED flashes once: A signal is detected, and the detector sends a signal to the alarm unit.

•LED continuously on: Low-voltage indication, please change the battery as soon as possible.

Advanced features

The Tiiwee PIR sensor is equipped with some additional features to allow you to adjust the device to

your specific needs. To access these functions, remove the screw at the top of the sensor. Then

separate the two parts (front and back piece) by using an appropriate tool (screwdriver, i.e.). Now

you see the circuit board with the two switches.

1. The Indicator light can be switched off to save battery power (“Led off”position). In this

mode, an alarm signal will still be sent to the X1-siren. IMPORTANT: Please note that the

low battery indication is switched off in this setting.

2. A waiting time of 5 minutes between detections can be set to save battery power (“5 Min” or

“5s” switch). Use the 5-minute waiting period when your PIR sensor is set to result in a loud

siren alarm. We do not advise to use this mode in combination with the doorbell-sound

setting on your Alarm unit.

Changing Factory Settings

The factory settings are “5s” and “Led On”. The sensor will respect a 5-seconds waiting time between

2 signals and that the LED indicator light will always flash if a movement is detected. These are the

most commonly used settings.

1. If both switches are set to the ON position, as shown in picture 1, the LED will flash each time a

movement is detected. After each signal, a waiting time of 5 seconds allows a person to pass the

detector without triggering a signal continuously.

2. If the top switch is set to “Off”, the detector will respect a 5-minute delay before it will become

active again. This is a power saving mode. A doorbell-sound sound setting on the Alarm unit is not

advised with this delay.

3. If the lower switch is set to “Off”, the Led light will not flash when a signal is detected. This setting

saves battery power. This setting can be used if you want to avoid that a burglar is able to locate the

motion detector in the dark.

4. If both switches are in the “Off”position, as shown in Figure 2, the PIR sensor will respect a 5-

minute interval between 2 different signals, nor will the LED window flash.

Low-voltage Reminder: The indicator light will be continuously on when the voltage of the PIR is

lower than 2.4V unless its light has been switched off by setting the internal switches.

Detection Range Characteristics

Technical Features

Power: The PIR sensor is powered through 3 x AAA 1.5V alkaline batteries or by an external 5V/1A DC

power supply connected through the micro-USB port. The batteries can stay inside the sensor while

the external power supply is connected and in use. They will work as a power backup in case of 220V

power failure. The power adaptor is not included with the product.

Specifications

Trade name: tiiwee PIR sensor 02

FCC ID: 2BAP8TWPIR02

Standby Current: <50uA

Working Current:<20mA

Detecting Range: 4-8 m/110 degrees angle

Wireless Distance: 100m ( Open Area )

Wireless Frequency: 433MHz

Housing Material: ABS

Working Humidity: <80%

Detector Size: 106x67x45mm

FCC compliance statement

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) this device may not cause harmful interference, and (2) this device must accept any

interference received, including interference that may cause undesired operation.

Warning: changes or modifications not expressly approved by the party responsible for compliance

could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions,

may cause harmful interference to radio communications. However, there is no guarantee that

interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and receiver.

•Connect the equipment into an outlet on a circuit different from that to which the receiver is

connected.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

13. Customer service

If additional support is required, please visit www.tiiwee.com. Here you can find additional support

material as well as our support videos in your own language.

You can also contact us under info@tiiwee.com. We respond within 24 hours to all questions, but

mostly still on the same day.

14. Warranty and liability

90 Day Limited Warranty

Tiiwee B.V. warrants this product to be free from manufacturing defects for a period of 90 days from

the original date of consumer purchase. This warranty is limited to the repair or replacement of this

product only and does not extend to consequential or incidental damage to other products that may

be used with this unit. This warranty does not cover products which have been abused, altered or

damaged. This warranty is in lieu of all other warranties expressed or implied. TO THE EXTENT

PERMITTED BY LAW, Tiiwee B.V. DISCLAIMS ALL OTHER IMPLIED OR EXPRESS WARRANTIES,

INCLUDING THE WARRANTY OF MERCHANTABILITY AND/OR FITNESS FOR A PARTICULAR PURPOSE.

Limitations of Liability

This limited warranty is your sole remedy and Tiiwee B.V. shall not be liable for any damages,

whether direct, indirect, incidental, special, consequential, exemplary or otherwise, including lost

revenue and lost profits, arising out of any theory of recover, including statutory, contract or tort. In

no event will Tiiwee B.V.'s entire liability exceed the purchase price of this product. Some States and

provinces do not allow the exclusion or limitations on how long an implied warranty lasts or permit

the exclusion or limitations of incidental or consequential damages, so the above limitations or

exclusions may not apply to you. This limited warranty gives you specific legal rights, and you may

also have other rights which vary from state to state and province to province.

If the product should prove defective within the period of warranty, please contact us under

[email protected].

15. FCC Regulation

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two

conditions: (1) This device may not cause harmful interference, and (2) This device must accept any

interference received, including interference that may cause undesired operation.

Warning: Changes or modifications to this product not expressly approved by the party responsible

for compliance could void the user's authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference in residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used

in accordance with the instructions, may cause harmful interference to radio communications.

However, there is no guarantee that interference will not occur in a particular installation. If this

equipment does cause harmful interference to radio or television reception, which can be

determined by turning the equipment off and on, the user is encouraged to try to correct the

interference by one or more of the following measures:

•Reorient or relocate the receiving antenna.

•Increase the separation between the equipment and the receiver.

•Consult the dealer or an experienced radio/TV technician for help.

FCC Radiation Exposure statement

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled

environment. This equipment should be installed and operated with minimum distance 20cm

between the radiator and your body. This transmitter must not be co-located or operating in

conjunction with any other antenna or transmitter.

FCC certification

Product Name

Product Model

FCC ID

tiiwee window sensor 03

TWWS03

2BAP8TWWS03

tiiwee PIR sensor 02

TWPIR02

2BAP8TWPIR02

tiiwee remote control 03

TWRC03

2BAP8TWRC03

GERMANY - DEUTSCH

Tiiwee X1 Alarm-Kits

1. Haftungsauschluss

2. Einführung

3. Überblick über das System

4. Installieren Sie Ihr Tiiwee-Alarmsystem in vier einfachen Schritten

5. Täglicher Gebrauch Ihres Alarmsystems

6. Erweitern Sie Ihr System

Anschließen zusätzlicher Türsensoren

Anschluss von PIR-Bewegungsmeldern

Anschließen von Fernbedienungen

Hinzufügen zusätzlicher Sirenen zu Ihrem System

7. Löschen von Zubehör oder Ändern der Zonen

Löschung aller Sensoren aus einer Zone. Wiederanschließen eines Sensors an eine Zone.

Trennen von Fernbedienungen

8. Batterielebensdauer und niedrige Batteriespannung

9. Ersetzen von Batterien

10. Zurücksetzen der X1-Sirene auf Werkseinstellungen

11. Fenster- und Türsensoren

12. PIR-Bewegungssensoren

13. Kundendienst

1. Haftungsausschluss

Testen

Es wird empfohlen, dass der Alarm unmittelbar nach der Installation und in regelmäßigen Abständen

von höchstens einem Monat getestet wird. Hinweis: Ein Tuch kann während des Tests verwendet

werden, um die Sirene abzudecken und die Schallleistung des Alarms zu reduzieren.

Warnung

Risiko von Personenschäden: Eine längere Exposition gegenüber der Alarmsirene kann zu

permanentem Hörverlust führen. Nur für den Innenbereich geeignet. Nicht in feuchten Umgebungen

verwenden.

Einschränkungen von Alarmprodukten

Testen Sie das Produkt regelmäßig, um sicherzustellen, dass es gemäß diesen Anweisungen

funktioniert. Tiiwee B.V. bietet keine Versicherung oder Garantie dafür, dass das Risiko von Einbruch

oder Raub selbst bei ordnungsgemäßem Gebrauch dieses Produkts verringert oder verhindert wird.

Tiiwee B.V. empfiehlt den Benutzern, eine angemessene Versicherungsdeckung für diese Risiken zu

erhalten. Tiiwee B.V. garantiert nicht, dass dieses Produkt nicht kompromittiert oder umgangen

werden kann, dass es angemessene oder ausreichende Warnungen liefert oder dass die Verwendung

dieses Produkts Verletzungen, Sachschäden oder andere Verluste verhindert. Beachten Sie, dass

dieses Produkt wie jede andere Alarmvorrichtung umgangen, kompromittiert, versagen oder nicht

warnen kann, einschließlich aufgrund von unsachgemäßer Installation, Positionierung oder Wartung,

Manipulation; leere, defekte oder falsch installierte Batterien; Begrenzungen bei der Erkennung und

Komponentenausfällen.

Die hörbaren Alarmsignale können außerhalb des Hörbereichs liegen, durch Türen, Wände und

Böden gedämpft werden, von tief schlafenden Personen oder den Hörbeeinträchtigten nicht gehört

oder von anderen Geräuschen übertönt werden.

Batteriewarnung

Achtung: Batterien können schädliche Flüssigkeiten oder entzündliche Materialien auslaufen oder

explodieren und Verletzungen und Produktschäden verursachen.

• Keine alten und neuen Batterien oder anderen Batterietypen mischen

• Ersetzen Sie alle Batterien gleichzeitig

• Ersetzen Sie vollständig entladene Batterien sofort.

2. Einführung

Herzlichen Glückwunsch zu Ihrem neuen X1 Tiiwee Alarm Kit. Das Tiiwee-Alarmset ist ein vielseitiges

Alarmsystem, das erkennt, wenn Menschen oder Tiere Ihr Haus oder Ihr Geschäft betreten. Es

ermöglicht Ihnen die Verwendung mehrerer Sensoren mit einem oder mehreren Alarmen in bis zu

vier verschiedenen Zonen. Diese Sensoren (PIR-Bewegungssensoren, Fenster-/Türsensoren) werden

drahtlos mit einer Alarmeinheit ("X1-Sirene") verbunden. Diese Alarmeinheit erzeugt einen

Türklingelton oder eine sehr laute Sirene. Die Alarmeinheit kann an einer festen Stelle angebracht

oder mitgenommen werden, wenn Sie sich im Haus bewegen oder schlafen gehen.

An jede Zone können maximal 10 Sensoren angeschlossen werden. Außerdem können bis zu 10

Fernbedienungen mit jeder Alarmeinheit gepaart werden. Ein Sensor oder eine Fernbedienung kann

bei Bedarf mit mehreren Alarmeinheiten gepaart werden.

Vorgesehene Verwendung

Das Tiiwee Home Alarm System ist in erster Linie dazu gedacht, Einbrecher abzuschrecken, wenn sie

in Ihr Haus eindringen. Das Herzstück des Systems ist die X1-Sirene. Platzieren Sie die Sirene in Ihrer

Wohnung dort, wo Einbrecher am ehesten eindringen. Wenn Sie eine größere Wohnung haben,

erwägen Sie bitte, zusätzliche Tiiwee X1- oder A3- (Außen-) Sirenen zu installieren.

Das System ist einsatzbereit. Ihr System ist vorkonfiguriert, und die Sensoren und Fernbedienungen

sind an die X1-Sirene angeschlossen. Die Fenstersensoren sind an Zone 1 angeschlossen. Wenn ein

PIR-Bewegungssensor vorhanden ist, wird dieser an Zone 2 angeschlossen. Wir empfehlen Ihnen,

dieses Benutzerhandbuch sorgfältig zu lesen und sich mit seinem Funktionsprinzip und den

Möglichkeiten zur Feinabstimmung auf Ihre Bedürfnisse vertraut zu machen.

3. Überblick über das System

Ein/Aus-Schalter

CONNECT-Taste

Sirene

Anzeige der Zone

Other manuals for X1

Table of contents

Languages:

Other Tiiwee Security System manuals

Tiiwee

Tiiwee TWWA01 User manual

Tiiwee

Tiiwee X4 Motion Sensor Alarm User manual

Tiiwee

Tiiwee X1 User manual

Tiiwee

Tiiwee Starter Kit User manual

Tiiwee

Tiiwee Pager User manual

Tiiwee

Tiiwee X3 Home Alarm Starter Kit User manual

Tiiwee

Tiiwee Starter Kit User manual

Popular Security System manuals by other brands

Tynetec

Tynetec Aidcall FM0743 manual

Wolf-Guard

Wolf-Guard YL007-M2C user manual

SECURITY HUB

SECURITY HUB STARTER KIT quick start guide

Cobra

Cobra P1703-141 manual

STI

STI STI-SA5500 quick start guide

Appello

Appello LivingHub manual

Ei Electronics

Ei Electronics Ei156TL User instructions

MG KS2 instruction manual

Philips

Philips lifeline Quick setup guide

DSC

DSC MAXSYS PC4020 instruction manual

System Sensor

System Sensor LASS-WSS-NC Installation and maintenance instructions

CrossXfire

CrossXfire CFH10 owner's manual

SkyLink

SkyLink SC-100 Guide Quick setup guide

SECURICO

SECURICO VENUS user manual

Silencer

Silencer 7919P owner's manual

Adesys

Adesys Octalarm-Touch quick start

ResMed

ResMed Power Station II user guide

Interlogix

Interlogix ACL800SUW-BSMF installation manual