TimeTec ProFace X User manual

Installation Guide
OVERVIEW INSTALLATION ENVIRONMENT
Please refer to the following recommendations for
installation.
INDOOR USE KEEP DISTANCE AVOID GLASS AVOID DIRECT KEEP EFFECTIVE
REFRACTION SUNLIGHT DISTANCE
AND EXPOSURE 0.3-2.5m
Speaker
Reset button
Note: Not all products have the function with *, the real product shall prevail.
DEVICE INSTALLATION
INSTALL ON THE WALL
1Attach the mounting
template sticker to the wall,
and drill holes according to
the mounting paper.
w w w . t i m e t e c c l o u d . c o m
ProFace X/TD
Face Recognition Access Control Device with Fever Detection
Exit
button
Auxiliary
input
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
Alarm
Lock
Sensor
GND
+12V Power
GND
INWD0
INWD1
Wiegand
In
Wiegand
Out
12V
GND
WD0
WD1
RS232
RS485
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
Tamper switch
Flash
Thermal infrared temperature
measurement module
Near-infrared
flash
Microphone*
Camera & Palm collector
8”touchscreen
Flash
Near-infrared flash
10ft
6.5ft
window
1.5m
4Fasten the device
to the back plate
with a security
screw.
3Attach the device to the
back plate.
2Fix the back plate
on the wall using
wall mounting
screws.

DOOR SENSOR, EXIT BUTTON & ALARM
CONNECTION
STANDALONE INSTALLATION LOCK RELAY CONNECTION
INSTALL ON THE BARRIER GATE
Please thread the wire through the bracket before
installation.
1Drill a hole on the barrier gate, insert the bracket
into the hole and fix it with a nut.
2Adjust the angle of the device.
①
②
Output
Wiegand
Door Sensor
AlarmCard Reader
Smoke
Detector
Exit
Button
Electric Lock
Door sensor
Alarm power
Alarm
-
+
-+
-+
-+
Detector power
Smoke detector
Exit button
AUX
AL+
AL-
NC
COM
NO
BUT
GND
SEN
GND
GND
The system supports Normally Opened Lock and Nor-
mally Closed Lock.
The NO LOCK (normally unlocked when power-on) is
connected with ‘NO’ and ‘COM’ terminals, and
the NC LOCK (normally locked when power-on) is con-
nected with ‘NC’ and ‘COM’ terminals.
Take NC Lock as an example below:
Device not sharing power with the lock
*Do not reverse the polarity
Device sharing power with the lock
Normally Closed Lock
DC12V
DC12V
+12V
GND
FR107
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+
*Maximum 30V 3A input.
FR107
Normally Closed Lock
DC12V
+12V
GND
GND
AUX
GND
SEN
GND
BUT
NO
COM
NC
AL-
AL+

12V 3A DC
© 2020 Timetec Cloud Sdn Bhd. All rights reserved.
Default IP address:
192.168.1.201
Subnet mask:
255.255.255.0
IP address: 192.168.1.130
Subnet mask: 255.255.255.0
WIEGAND READER CONNECTION
w w w . t i m e t e c c l o u d . c o m
Access controller
+12V
GND
Wiegand reader
INWD0
INWD1
12V
GND
WD0
WD1
BARRIER CONNECTION
RS485 CONNECTION
Barrier gate
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
+12V
GND
GND
485+
485-
12V
485B
485A
GND
TXD1
RXD1
GND
GND
GND
12V
12V
485 reader
Note: 485A and 485B can be connected to the barrier gate or the
485 reader, but cannot be connected to the gate and the reader at
the same time.
POWER CONNECTION
Recommended power supply: 12V - 3A
To share the power with other devices, use a power supply
with higher current ratings.
ETHERNET CONNECTION
Connect the device and computer software over an Ether-
net cable. An example is shown below:
Note: In LAN, IP addresses of the server (PC) and the device must be in the same network
segment when connecting to the software.
Click on [Comm.] > [Ethernet] > [IP Address], input the IP ad-
dress and click on [OK].