tissin TS200 Series User manual

Lock Up Valve
TS200 Series
Instruction Manual
Ver. PM-TS200EN_9/2017

tissin
www.tissin.co.kr
2
Lock Up Valve
TS200 Series
Description
The pneumatic lock up valve TS200 Series
shuts off the signal pressure line either when
the air supply falls below an adjusted value or
upon complete air supply failure. This causes
the actuator to remain in its last position.
Features
Quick Response and High Precision.
Easy set-up of lock up air pressure.
When the signal pressure is more than
the set pressure, it allows to open the air
pressure line automatically.
Small size and light weight allow the Lock
Up Valve to be installed in the direct pipe
fitting line without bracket.
Options available (High & Low Tempera-
ture).
Warranty
This product has been fully inspected and
shipped through a thorough quality
inspection procedure. The manufacturer
warranty period of the product is 18
months after the product is shipped from
Tissin in Korea.
For any failure or damage reported within
the warranty period which is clearly our
responsibility, a replacement product or
necessary parts will be provided. This
limited warranty applies only to our
product independently, and not to any
other damage incurred due to the failure
of the product.
Using the device in a manner that does
not fall within the scope of its intended
use, disregarding this manual, using
under qualified personnel, or making
unauthorized alterations releases the
manufacturer from liability for any
resulting damage. This renders the
manufacturer's warranty null and void.
Precautions
General Information
Please ensure to read and understand the
manual before installation and mainte-
nance of the products.
The manual should be passed to the End-
User.
When the product is not used within its
description range, it may cause the
product to malfunction so please follow
the product manual instructions.
The manual may be modified by us
without any prior notice. When you require
the latest information, please visit our
website. http://www.tissin.co.kr .
Handling Precautions
Do not install, operate or maintain without
being fully trained and qualified in Valve
and accessory installation.
When exceeding the permitted air
pressure range, it may cause injury or
property damage due to compressed air
explosion. So it is very important to
carefully read, understand and follow all of
the contents of the relevant product
manual.
User Environment
Do not use in corrosive environments.
When used in environments that are a
higher temperature than the specified
temperature range, it may cause a lower
life cycle of the product. So please ensure
to use within the specified temperature
range. (Refer to Page 3)

tissin
www.tissin.co.kr
3
Lock Up Valve
TS200 Series
Specifications
Materials of Construction
TS200S TS200D
Principle of Operation
When signal pressure is greater than setting
pressure level, upper diaphragm(3) moves
upward, the exhaust valve is closed, the signal
pressure pushes the lower diaphragm(4),
lower diaphragm(4) pushes shaft push(5) and
shaft push(5) pushes seat(6), and the flow can
go from IN to OUT. When signal pressure is
less than setting pressure level, upper
diaphragm(3) is being pushed downward and
the pressure of lower pressure diaphragm is
exhausted from the exhaust valve. Therefore,
the valve is closed by spring force and air
circuit is shut down.
The spring(2) force can be adjusted by shaft
adjust(1)
The factory setting signal pressure is 0.3Mpa.
Item.Type TS100
Signal Pressure 0.14~0.7MPa
Max Supply Pressure 1MPa
Max Lock Up
Pressure 0.7MPa
Differential Pressure Below 0.01MPa
Flow Capacity(CV) 0.9
Signal Connection PT(NPT)1/4
Supply/Output
Connection PT(NPT)1/4
Operating Temp. -20℃~70℃
(Standard type)
Material Aluminum Diecasting
Weight 1.3kg

tissin
www.tissin.co.kr
4
Lock Up Valve
TS200 Series
Product Number
Model TS200
Acting Type Single S
Double D
Air
connection PT1/4 P
NPT1/4 N
Ambient
Temp -20℃~70℃ S
-20℃~120℃H
-40℃~70℃ L
Product Number
MODEL
Indicates the model number.
SERIAL NO.
Indicates the serial No
MAX.SIG.PRESS 1.0MPa
Indicates max signal air pressure.
SET.PRESS 0.14~0.7MPa
Indicates settable air pressure range.
Pneumatic Connection
①Connect the Positioner’s Output Port with
the Lock Up Valve’s In Port.
②Connect the Lock Up Valve’s Output port
with the Actuator.
③Connect Lock Up Valve’s Signal with the
detect the signal port.
Bracket Installation
If you need to install brackets, you can
referring to product dimension drawing make
the bracket, and install it as below.

tissin
www.tissin.co.kr
5
Lock Up Valve
TS200 Series
Installation Example
<Single acting linear type actuator> <Double acting rotary type actuator>
Dimensions (Unit:mm)
TS200S
TS200D

Tissin Co.,Ltd.
201-1105,No 397,Seokcheon-ro,Ojeong-gu,
Bucheon-Si, Gyeonggi-do, Korea
Tel : [phone], Fax : [phone]
www.tissin.co.kr
Solutions for Control Valve System