turck TX700 HMI/PLC Series User manual

Your Global Automation Partner
Operating instructions
TX700
HMI/PLC Series

2 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com


3
2018/09
1 About this Document 5
1.1 Target Groups 5
1.2 Explanation of Symbols Used 5
1.3 Other Documents 5
1.4 Feedback about these Instructions 6
2 Product Overview 6
2.1 Product Identication 6
2.2 Type Code 7
2.3 List of Available Devices 7
3 Standards and Approvals 8
3.1 Special Instruction for Use 8
4 Technical Specications 9
4.1 Technical Data 9
4.2 Environmental Conditions/Protection Class 10
4.3 Electromagnetic Compatibility (EMC) 10
4.4 Dimensions 11
4.4.1 TX705 11
4.4.2 TX707/TX710/TX715/TX721 12
5 Installing the HMI 13
5.1 Installation Environment 13
5.2 Mounting of the HMI 13
6 Connecting 14
6.1 Connecting TX705 14
6.2 TX707/TX710/TX715/TX721 15
6.3 Serial Port 16
6.4 Ethernet Ports 16
6.5 SD Card Slot 17
6.6 USB Port 17
7 Optional Plug-in Modules 17
7.1 Slot Assignment – CAN-Port 18
7.2 Slot Assignment – Serial Interfaces 18
7.3 Optional Plug-in Module Installation Procedure 19
8 Connecting the Power Supply 20
8.1 Grounding the device 20
9 Battery 21
9.1 TX705 22
9.2 TX707/TX710/TX715/TX721 22

Table of Contents

4 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
10 Special Instruction for Use 23
11 Getting Started 23
11.1 Programming with CODESYS 23
11.2 Programming with TX VisuPro 23
12 Adapting the System Settings 24
12.1 Access the System Settings in User Mode 24
12.2 Access the System Settings in System Mode 25
13 Unpacking and Packing the Device 26
13.1 TX705/TX707/TX710 26
13.2 TX715/TX721 26
14 Appendix: Accessories 27
14.1 Plug-in Extension Modules 27
14.2 Mounting Material/Power Supply Connector 27
14.3 USB/SD Accessory 27

5
2018/09
1 About this Document
These operating instructions describe the structure, functions and the use of the product and
will help you to operate the product as intended. Read these instructions carefully before using
the product. This is to avoid possible damage to persons, property or the device. Retain the in-
structions for future use during the service life of the product. If the product is passed on, pass
on these instructions as well.
1.1 Target Groups
These instructions are aimed at qualified personnel and must be carefully read by anyone
mounting, commissioning, operating, maintaining, dismantling or disposing of the device.
1.2 Explanation of Symbols Used
The following symbols are used in this manual:
The following symbols are used in this manual:
DANGER!
DANGER indicates a dangerous situation with high risk of death or severe injury if not
avoided.
WARNING!
WARNING indicates a dangerous situation with medium risk of death or severe injury if
not avoided.
CAUTION! CAUTION indicates a dangerous situation of medium risk which may result in minor or
moderate injury if not avoided.
NOTICE!
ATTENTION indicates a situation that may lead to property damage, if it is not avoided.
NOTE
NOTE indicates tips, recommendations and useful information on specific actions and
facts. The notes simplify your work and help you to avoid additional work.
CALL TO ACTION
 This symbol denotes actions that the user must carry out.
RESULTS OF ACTION
 This symbol denotes relevant results of actions.
1.3 Other Documents
The following additional documents are available online at www.turck.com
■Data sheet
■Installation guide
■CAD data

6 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Product Overview
1.4 Feedback about these Instructions
We make every effort to ensure that these instructions are as informative and as clear as possi-
ble. If you have any suggestions for improving the design or if some information is missing in
the document, please send your suggestions to t[email protected].
2 Product Overview
Products have been designed as IoT edge devices with the combination of a powerful control-
ler with networking capability (up to 3 Ethernet networks) and outstanding communication
options including client/server OPC UA. They are the ideal choice for all demanding IoT edge
applications in factory, marine and building automation.
The glass projected capacitive touchscreen and the brilliant displays with size up to 21.5”and
resolution up to 1920x1080 guarantee great optical performance; with the support of multi-
touch gesture programming they can create the most natural human interfaces.
TX700 devices have been designed to run the TX VisuPro software for powerful HMI
applications.
■Gateway function with OPC UA Server and Client.
■Secure connectivity with JMcloud and full network separation
■Powerful browser wih industry standard Web engines
■Optional CODESYS V3 PLC runtime with choice of major I/O protocols
■Optional plug-in modules for fieldbus systems, I/O and controllers
2.1 Product Identication
The manual refers to the following models:
■TX705 Operator interface with TFT color 5”widescreen display multitouch projected
capacitive touchscreen
■TX707 Operator interface with TFT color 7”widescreen display multitouch projected
capacitive touchscreen
■TX710 Operator interface with TFT color 10.1”widescreen display multitouch projected
capacitive touchscreen
■TX715 Operator interface with TFT color 15.6”widescreen display multitouch projected
capacitive touchscreen
■TX721 Operator interface with TFT color 21.5”widescreen display multitouch projected
capacitive touchscreen

7
2018/09
The type plate is located on the rear of the device.
An example of this plate is shown in the figure below:
TX710 Product model name
100002031 Product part number
1832 Year/week of production
AA… Serial number number
V… Internal version ID of the product
2.2 Type Code
TX 7 05 –P3 CV 01
TX Produktfamilie
Produktfamilie
TX Turck HMI/PLC
7Serie
Serie
7TX700 Serie
05 Bildschirmdiagonale
Größe
05 5"
07 7"
10 10,1"
15 15,6"
21 21,5"
00 SPS
SPS
00 ohne SPS Funktionalität
P3 CODESYS V3 Runtime
XX Visualisierung
Visualisierung
XX ohne Visualisierungsfunktionalität
CV CODEYS V3 TargetVisu Runtime
NN Kommunikation
Kommunikation
NN ohne Kommunikation
01 PROFINET Controller
EtherNet/IPTM Scanner
Modbus TCP Master/Slave
Modbus RTU Master/Slave
Fig.1: Type Code TX700
2.3 List of Available Devices
Ident no. Device
100002029 TX705-P3CV01
100002030 TX707-P3CV01
100002031 TX710-P3CV01
100002032 TX715-P3CV01
100002033 TX721-P3CV01

8 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Standards and Approvals
3 Standards and Approvals
The products have been designed for use in an industrial environment in compliance with the
2014/30/EU EMC Directive.
The products have been designed in compliance with:
EN 61000-6-4 CISPR 22, Class A
CISPR 16-2-3
EN 61000-6-2 EN 61000-4-2
EN 61000-4-3
EN 61000-4-4
EN 61000-4-5
EN 61000-4-6
EN 61000-4-8
EN 61000-4-11
EN 61000-4-29
EN60945
ATTENTION!
Operation in residential and commercial areas
Electromagnetic disturbances!
 In case of the operation of the devices in residential and commercial areas, observe
the measurement values according to IEC-61000-6-3.
The products are in compliance with the Restrictions on Certain Hazardous Substances (RoHS)
Directive 2011/65/EU.
In compliance with the above regulations the products are CE marked.
3.1 Special Instruction for Use
■The equipment shall only be used in an area of not more than pollution degree 2, as defined
in IEC/EN 60664-1.
■The equipment shall be installed in an enclosure that provides a degree of protection not less
than IP 54 in accordance with IEC/EN 60079-15.
■Transient protection shall be provided that is set at a level not exceeding 140 % of the peak
rated voltage value at the supply terminals to the equipment.
■Care shall be taken not to allow layers of dust to form on the graphic panel in a way that
might cause the accumulation of static charges.

9
2018/09
4 Technical Specications
4.1 Technical Data
TX705 TX707 TX710 TX715 TX721
Touchscreen
technology
True Glass Projected Capacitive, Multitouch
Display/backlight TFT Color / LED
Colors 64 K 16M 16M 16M 16M
Brightness 300 Cd/m² typ. 500 Cd/m² typ. 500 Cd/m² typ. 400 Cd/m² typ. 300 Cd/m² typ.
Resolution 800x480 800 × 480 1280 × 800 13660 × 768 (HD) 1920 × 1080 (full HD)
Diagonal (inches) 5”widescreen
(16:9)
7’’ widescreen
(16:9)
10.1’’ widescreen
(16:9)
15.6’’ widescreen
(16:9)
21.5’’ widescreen
(16:9)
Dimming yes
CPU A8, 1 GHz A9 dual core,
800 MHz
A9 dual core,
800 MHz
A9 quad core,
800 MHz
A9 quad core,
800 MHz
Operating System Linux RT
Flash 4 GB 4 GB 4 GB 8 GB 8 GB
SD card slot yes
RAM 512 MB 1 GB 1 GB 2 GB 2 GB
Serial port (local) 1 (software configurable as RS232, RS485 or RS422)
Serial port
(extendable with
plug-in modules)
max. 1 max. 2 max. 2 max. 2 max. 2
Ethernet port 2 × 10/100 Mbit 2 × 10/100 Mbit, 1 × 10/100/1000 Mbit
USB Host port 1 × USB 2.0,
max. 500 mA
2 × USB 2.0, max. 500 mA
Expansion slot 1 × for optional
plug-in modules
2 × for optional plug-in modules
Voltage supply DC Power Connector - AWG24 wire size - R/C Terminal Blocks (XCFR2),
Female pitch 5.08 mm, torque 4.5 lb-in. 3 conductor, 1,5 mm² wire size minimum, minimum tempera-
ture conductor rating 105 °C.
Real Time Clock yes
Back-up battery 3 V, 50 mAh Lithium, rechargeable, not replaceable, type VL2330
Operational voltage 24 VDC (10…32 VDC)
Current consump-
tion (at 24 VDC)
0.6 A 0.7 A 1 A 1.2 A 1.7 A
Weight 1 kg 1.3 kg 1.7 kg 4.1 kg 6.1 kg
Input protection automatic Electronic Electronic Electronic Electronic
Accuracy RTC
(at 25 °C)
< 100 ppm
NOTE
For applications requiring compliance with EN 61131-2 and specifically in reference to 10 ms
voltage dips, the minimum power supply voltage is 18 VDC.

10 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Product Overview
4.2 Environmental Conditions/Protection Class
Environmental conditions
Operating temperature (surrounding air temperature) -20…+60 °C (vertical installation)
Plug-in modules and USB devices may
limit max temperature to +50 °C
EN 60068-2-14
Storage temperature -20…+70 °C EN 60068-2-1
EN 60068-2-2
EN 60068-2-14
Operating and storage humidity 5…85 % RH non-condensing EN 60068-2-30
Vibrations 5…9 Hz, 7 mmp-p
9…150 Hz, 1 g
EN 60068-2-6
Shock ± 50 g, 11 ms, 3 pulses per axis EN 60068-2-27
Protection class
Front panel IP66 EN 60529
Rear IP20 EN 60529
4.3 Electromagnetic Compatibility (EMC)
Electromagnetic Compatibility (EMC)
Radiated disturbance test Class A CISPR 22, CISPR 16-2-3
Electrostatic discharge immunity test 8 kV (air electrostatic discharge)
4 kV (contact electrostatic discharge)
EN 61000-4-2
Radiated, radio-frequency,
electromagnetic field immunity test
80 MHz …1 GHz, 10 V/m
1,4 GHz … 2 GHz, 3 V/m
2 GHz … 2.7 GHz, 1 V/m
EN 61000-4-3
Burst immunity test ± 2 kV DC power port
± 1 kV signal line
EN 61000-4-4
Surge immunity test ± 0,5 kV DC power port (line to earth)
± 0,5 kV DC power port (line to line)
± 1 kV signal line (line to earth)
EN 61000-4-5
Immunity to conducted disturbances inducted by
radiofrequency field
0.15…80 MHz, 10 V EN 61000-4-6
Power frequency magnetic field
immunity test
Enclosure, 50/60Hz, 30A/m EN 61000-4-8
Voltage dips, short interruptions and
voltage variations immunity test
Port: AC mains; Level:
100 % duration: 1 cycle and 250 cycles (50 Hz);
40 % duration: 10 cycles (50 Hz);
70 % duration: 25 cycles (50 Hz);
Phase: 0°-180°
Test executed on the 230 VAC side of the power supply EN 61000-4-11
Port: DC mains; Level:
0% duration: 10ms 20 spaces by 1s
Test executed on the 24Vdc of the EUT EN 61000-4-29
Durability information
Backlight service life (LED type) 40.000 hours or more
(Time of continuos operation until the brightness of the backlight
reaches 50 % of the rated value when the surrounding air tempera-
ture is 25 °C).

11
2018/09
NOTE
Extended use in environments where the surrounding air temperature is 40 °C or higher may
degrade backlight quality/reliability/durability.
4.4 Dimensions
4.4.1 TX705
Fig.2: Dimensions TX705
Model A B C D E F
TX705 147 mm/5.78” 107 mm/4.21” 136 mm/5.35” 96 mm/3.78” 56 mm/2.40” 8 mm/0.31”

12 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Product Overview
4.4.2 TX707/TX710/TX715/TX721
Fig.3: Dimensions TX707/TX710/TX715/TX721
Model A B C D E F
TX707 187 mm/7.36” 147 mm/5.79” 176 mm/6.90” 136 mm/5.35” 47 mm/1.85” 8 mm/0.31”
TX710 282 mm/11.10” 197 mm/7.80” 271 mm/10.67” 186 mm/7.32” 56 mm/2.20” 8 mm/0.31”
TX715 422 mm/16.60” 267 mm/10.50” 411 mm/16.18” 256 mm/10.00” 56 mm/2.20” 8 mm/0.31”
TX721 552 mm/21.73” 347 mm/13.66” 541 mm/21.30” 336 mm/13.22” 56 mm/2.20” 8 mm/0.31”

13
2018/09
5 Installing the HMI
5.1 Installation Environment
Avoid prolonged exposition to direct sunlight to avoid the risk of overheating the device.
The equipment is not intended for installation in contact with corrosive chemical compounds.
Check the resistance of the front panel film to a specific compound before installation.
 Do not use tools of any kind (screwdrivers, etc.) to operate the touch screen of the panel.
In order to meet the front panel protection class, proper installation procedure must be
followed:
■The borders of the cutout must be flat
■Screw up each fixing screw until the bezel corner get in contact with the panel.
■The cut-out for the panel must be of the dimensions indicated in this manual.
■The IP66 is guaranteed only under the following conditions:
ūMax. deviation from the plane surface to the cut-out: ≤ 0.5 mm
ūThickness of the case on which the equipment is mounted: 1,5 mm to 6 mm
ūMax. surface roughness where the gasket is applied: ≤ 120 µm
Fig.4: TX700 – Mounting
5.2 Mounting of the HMI
NOTE
For all installation notes, please refer to the Installation Guide provided with the
product.

14 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Connecting
 Place the fixing brackets contained in the fixing kit as follows:
Fig.5: Mouting the fixing brackets
 Screw each fixing screw until the bezel corners get in contact with the HMI.
NOTE
Tightening torque: 130 Ncm or screw each fixing screw until the bezel corner gets in
contact with the panel.
6 Connecting
6.1 Connecting TX705
Fig.6: TX705 – connection options
Connector Description
1 USB Port
2 Power supply
3 Serial Port
4 Ethernet port 0 (10/100 Mbit)
5 Ethernet port 1 (10/100 Mbit)
6 Expansion slot for plug-in modules
7 SD card slot

15
2018/09
6.2 TX707/TX710/TX715/TX721
Fig.7: TX707/TX710/TX715/TX721 – connection options
Connector Description
1 USB Port
2 Ethernet port 2 (10/100 Mbit)
3 Ethernet port 1 (10/100 Mbit)
4 Serial port
5 Ethernet port 0 (10/100/1000 Mbit)
6 Power supply
7 2 × Expansion slot for plug-in modules
8 SD card slot

16 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [e-mail] | www.turck.com
Connecting
6.3 Serial Port
The serial port is used to communicate with a PLC or with another type of device.
Different electrical standards are available for the signals in the PLC port connector: RS232,
RS422, RS485.
The serial port is software programmable. Make sure you select the appropriate interface in the
programming software.
Fig.8: Serial port
Pin RS232 RS422/RS485
1RX CHB-
2TX CHA-
3CTS CHB+
4RTS CHA+
5+5 VDC output +5V output
6 GND GND
7 n.c. n.c.
8 SHIELD SHIELD
NOTE
To operate in RS485, pins 1-2 and 3-4 must be connected externally.
The communication cable must be chosen for the type of device being connected.
6.4 Ethernet Ports
The Ethernet ports have two status indicators. .
Fig.9: Ethernet ports

17
2018/09
6.5 SD Card Slot
Specication
Supported types SD, SDHC
Format FAT, FAT32
Max. size Limited by the FAT32 specification
≤ 4 GB for one single file
≤ 32 GB in total
6.6 USB Port
Allowed formatting
Format FAT, FAT32
Max. size Limited by the FAT32 specification
≤ 4 GB for one single file
≤ 32 GB in total
7 Optional Plug-in Modules
TX700 HMIs have several optional plug-in modules, multiple module configurations are
possible.
Fig.10: Slots for plug-in modules
Slot#2 and Slot#4 are available only if the plug-in module has the“bus extension connector”.
Each slot carries 3 communication channels:
■1 serial interface
■1 CAN interface
■1 SPI interface

18 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [email protected] | www.turck.com
Optional Plug-in Modules
NOTE
It is not possible to stack two modules that are using the same type of interface.
The following table shows, which plug-in module and how many plug-in modules can
be used at which HMI:
Module Application Max. Modules Interface type/
communication
channel
Bus
Extension
connector
TX-CAN CAN –1 for TX705
–2 for all other TX700 models CAN yes
TX-RS485 RS485/RS422 Serial yes
TX-RS232 RS232 Serial yes
TX-IO-DX06 Multifunction I/O –1 for all TX700 models I/O (SPI) no
TX-IO-XX03 Compact I/O –1 for TX705 (can not be
plugged directly, additional
module with extension slot
necessary, CAN or RS×××)
–2 for all other TX700 models
I/O (SPI) no
The column max. modules refers to the max. number of modules which can be plugged into
the HMI (all slots).
7.1 Slot Assignment – CAN-Port
Physical interface CODESYS parameter
“Network”
Slot 1 Network 0
Slot 2 Network 0
Slot 3 Network 1
Slot 4 Network 1
7.2 Slot Assignment – Serial Interfaces
Physical interface CODESYS parameter
“Device/Interface Parameter”
CODESYS parameter
”Modbus COM/COM Port”
local serial COM port Mode COM1 COM Port 1
Slot 1 Mode COM2 COM Port 2
Slot 2 Mode COM2 COM Port 2
Slot 3 Mode COM3 COM Port 3
Slot 4 Mode COM3 COM Port 3

19
2018/09
Slot 1 to Slot 4 refer to the Extension Slots on the rear of the device, see„Abb. 10: Erweiterungss-
teckplätze für Plug-in-Module“ S. 17.
7.3 Optional Plug-in Module Installation Procedure
TX-CAN/ TX-IO-DX06 TX-IO-XX03
Fig.11: Installation of optional plug-in modules

20 Hans Turck GmbH & Co. KG | T [phone] | F [phone] | [email protected] | www.turck.com
Connecting the Power Supply
8 Connecting the Power Supply
The power supply terminal block is shown in the figure below.
Fig.12: Power supply terminal block
NOTE
Ensure that the power supply has enough power capacity for the operation of the
equipment.
8.1 Grounding the device
The unit must always be grounded to earth with A minimum of 1.5mm². Grounding helps to
limit the effects of noise due to electromagnetic interference on the control system.
The earth connection will have to be done using the grounding screw located near the pow-
er supply terminal block. The screw for the ground connection is marked with an engraved
ground symbol. Also connect terminal 3 on the power supply terminal block to ground.
The power supply circuit may be floating or grounded. If the power supply circuit is grounded,
connect to ground the power source common as shown in figure (see below) with a dashed
line.
When using the floating power scheme, note that the device internally connects the power
common to ground with a 1 MΩ resistor in parallel with a 4,7 nF capacitor.
The power supply must have double or reinforced insulation.
The suggested wiring for the power supply is shown below.