Titan Fitness UPHDPWRv2-24HDPWR User manual

MPN(s): UPHDPWRv2-24HDPWR, UPHDPWRv2-36HDPWR, INBENCH,
UPHDPWRv2-24HDPWR-INBENCH, UPHDPWRv2-36HDPWR-INBENCH

2
KEY
DESCRIPTION
QTY
(A)
WEIGHT HOLDER
x4
(B)
UPRIGHT
x4
(C)
TUBE END CAP
x4

3

4
KEY
DESCRIPTION
QTY
(1)
SIDE BRACE
x4
(2)
2” PULL-UP BAR
x1
(3)
1.25” PULL-UP BAR
x1
(4)
BAND PEG
x4
(5)
SPOTTING BAR SLEEVE
x2
(6)
HDJ-HOOK
x2
(7)
SPOTTING BAR
x2
(8)
HEX BOLT M16x120
x8
(9)
FLAT WASHER M16
x32
(10)
SPRING WASHER M16
x32
(11)
HEX NUT M16
x32
(12)
HEX BOLT M16x110
x16
(13)
HEX BOLT M16x80
x8

5
STEP 1

6
STEP 2
Use hardware that is identified below for both sides of a part’s installation.
----- THIS CONCLUDES THE ASSEMBLY OF THE UPHDPWRV2-24HDPWR/36HDPWR. -----

7

8
KEY #
DESCRIPTION
QTY
(1)
FRAME
x1
(2)
REAR STABILIZER
x1
(3)
FRONT STABILIZER
x1
(4)
BACKREST FRAME
x1
(5)
SEAT FRAME
x1
(6)
BACKREST PIVOT BRACKET
x1
(7)
SEAT PIVOT BRACKET
x1
(8)
BACKREST
x1
(9)
SEAT
x1
(10)
M10x100 BOLT
x2
(11)
M8x60 BOLT
x4
(12)
M8x40 BOLT
x2
(13)
M8x15 BOLT
x16
(14)
M10 NYLON LOCKNUT
x2
(15)
M8 NYLON LOCKNUT
x2
(16)
M10 WASHER
x4
(17)
M8 WASHER
x20
(18)
INNER WASHER #10.5
x4
(19)
POP PIN
x2
(20)
SQUARE INNER CAP
x4
(21)
HANDLE
x1
(22)
RING
x2
(23)
CUSHION
x1
(24)
ROUND DOME
x2
(25)
WHEEL
x2

9
1. SECURE THE FRAME (1) TO THE REAR STABILIZER (2) AND THE FRONT STABILIZER (3):
I. Align the holes at the base of the FRAME (1) to those drilled through the REAR STABILIZER (2).
II. Insert an M8x60 BOLT (11) through one hole and partially tighten the M8x60 BOLT (11).
III. Insert an M8x60 BOLT (11) through the remaining hole and partially tighten the M8x60 BOLT (11).
IV. When both M8x60 BOLTS (11) are in place and partially tightened, tighten the M8x60 BOLTS (11)
until the FRAME (1) is securely attached to the REAR STABILIZER (2).
V. Repeat the above order for attaching the FRAME (1) to the FRONT STABILIZER (3).
STEP 1

10
2. ATTACH THE BACKREST FRAME (4) AND SEAT FRAME (5) TO THE FRAME (1):
I. Align the topmost hole of the BACKREST FRAME (4), which is located within the bracket on the
FRAME (1), with the hole through the bracket located closest to the REAR STABILIZER (2).
II. Attach the BACKREST FRAME (4) to the FRAME (1) using M10x100 BOLT (10), M10 WASHER (16),
M10 NYLON LOCKNUT (14), and INNER WASHER #10.5 (18). The order for assembly is as follows:
M10x100 BOLT (10), M10 WASHER (16), FRAME (1), INNER WASHER #10.5 (18), BACKREST FRAME
(4), INNER WASHER #10.5 (18), FRAME (1), M10 WASHER (16), and M10 NYLON LOCKNUT (14).
III. Once each piece is in place, tighten down the M10 NYLON LOCKNUT (14).
IV. Align the bottommost hole of the SEAT FRAME (5), which is located within the bracket on the
FRAME (1), with the hole through the bracket located closest to the FRONT STABILIZER (3).
V. Repeat the above order for assembly.
VI. Once each piece is in place, tighten down the M10 NYLON LOCKNUT (14).
STEP 2

11
3. ATTACH THE SEAT FRAME (5) TO THE SEAT PIVOT BRACKET (7) AND THE POP PIN (19)
TO THE FRAME (1):
I. Align the holes of the SEAT PIVOT BRACKET (7) with those on the SEAT FRAME (5).
II. Attach the SEAT PIVOT BRACKET (7) to the SEAT FRAME (5) using an M8x15 BOLT (13) and an M8
WASHER (17). The order for assembly is as follows: M8x15 BOLT (13), M8 WASHER (17), SEAT
PIVOT BRACKET (7), and SEAT FRAME (5).
III. Lightly tighten down the M8x15 BOLT (13) and repeat the process for the remaining SEAT PIVOT
BRACKET (7) placement points.
IV. Tighten down each M8x15 BOLT (13) when all are in place.
V. Insert the SEAT PIVOT BRACKET (7) into the bracket located on the side of the FRAME (1) and
insert the POP PIN (19) through the bracket and the SEAT PIVOT BRACKET (7).
VI. Screw the POP PIN (19) into position. (This will lock the SEAT PIVOT BRACKET (7) in place and be
how the height of the seat is adjusted.)
STEP 3

12
4. ATTACH THE BACKREST FRAME (4) TO THE BACKREST PIVOT BRACKET (6) AND THE
POP PIN (19) TO THE FRAME (1):
I. Align the holes of the BACKREST PIVOT BRACKET (6) with those on the BACKREST FRAME (4).
II. Attach the BACKREST PIVOT BRACKET (6) to the BACKREST FRAME (4) using M8x15 BOLT (13) and
M8 WASHER (17). The order for assembly is as follows: M8x15 BOLT (13), M8 WASHER (17),
BACKREST PIVOT BRACKET (6), and BACKREST FRAME (4).
III. Lightly tighten down the M8x15 BOLT (13) and repeat the process for the remaining BACKREST
PIVOT BRACKET (6) placement points.
IV. Tighten down each M8x15 BOLT (13) when all are in place.
V. Insert the BACKREST PIVOT BRACKET (6) into the bracket located on the side of the FRAME (1) and
insert the POP PIN (19) through the bracket and the BACKREST PIVOT BRACKET (6).
VI. Screw the POP PIN (19) into position. (This will lock the BACKREST PIVOT BRACKET (6) in place and
be how the height of the backrest is adjusted.)
STEP 4

13
5. SECURE THE SEAT (9) TO THE SEAT FRAME (5):
I. Align the holes on the base of the SEAT (9) to the holes drilled in the brackets located
on top of the SEAT FRAME (5).
II. Secure the SEAT (9) to the SEAT FRAME (5) using an M8x15 BOLT (13) and an M8
WASHER (17). The order for assembly is as follows: M8x15 BOLT (13), M8 WASHER
(17), SEAT FRAME (5), and then SEAT (9).
III. Lightly tighten down the M8x15 BOLT (13) and repeat the above process for securing
the remaining side of the SEAT (9).
IV. Once all pieces are in place, completely tighten down the M8x15 BOLTS (13).
STEP 5

14
6. SECURE THE BACKREST (8) TO THE BACKREST FRAME (4):
I. Align the holes on the base of the BACKREST (8) to the holes drilled in the brackets
located on top of the BACKREST FRAME (4).
II. Secure the BACKREST (8) to the BACKREST FRAME (4) using an M8x15 BOLT (13) and
an M8 WASHER (17). The order for assembly is as follows: M8x15 BOLT (13), M8
WASHER (17), BACKREST FRAME (4), and then BACKREST (8).
III. Lightly tighten down the M8x15 BOLT (13) and repeat the above process for securing
the remaining side of the BACKREST (8).
IV. Once all pieces are in place, completely tighten down the M8x15 BOLTS (13).
STEP 6

15
This concludes the UPHDPWRv2 Owner’s Manual.
Make sure to tighten all nut-and-bolt combinations
before use.
Enjoy!
DISCLAIMER
This equipment must be used with care by capable and competent individuals under supervision, if necessary.
The use of any fitness equipment, including this one, involves the potential risk of injury. You accept and assume full
responsibility for any and all injuries, damages (both economic and non-economic), and losses of any type, which may
occur, and you fully and forever release and discharge Titan, its insurers, employees, officers, directors, associates, and
agents from any and all claims, demands, damages, rights of action, or causes of action, present or future, whether the
same be known or unknown, anticipated, or unanticipated, resulting from or arising out of the use of said equipment.
TITAN MAKES NO WARRANTY WHATSOEVER WITH RESPECT TO THE EQUIPMENT, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, WHETHER EXPRESS OR IMPLIED BY LAW,
COURSE OF DEALING, COURSE OF PERFORMANCE, USAGE OF TRADE OR OTHERWISE. BUYER ASSUMES ALL LIABILITY IN
USE OF THE EQUIPMENT.
NEED HELP?
CONTACT US FIRST.
1 [phone]
[e-mail] /
Business Hours: Monday–Friday • 8:00 a.m.–5:00 p.m. (CT)