Titan TTB772STM User manual

EN
Original Instructions_MNL_TTB772STM_GB_V1_20210804
TTB772STM
2000W Wallpaper
Stripper
EAN: 5059340118314
WARNING: Read the instructions before using the product!
BX220IM

EN
02
24
25
23
19
17
16
In more detail...
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
15
02
03
09
10
10
Getting started...
Technical and legal information
Your product
Technical
Before you start
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Let’s
get started...

EN
TTB772STM by TITAN
Getting started...
03
Technical and legal information
Safety warnings
1. This product can be used by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the product
in a safe way and understand the hazards involved.
2. Children shall not play with the product.
General safety warnings
WARNING! When using electric products basic
safety precautions should always be followed to
injury including the following.
Read all these instructions before attempting to
operate this product and save all warnings and
instructions for future reference.
Safe operation
1. Consider work area environment
• Do not expose the product to rain.
• Do not use the product in damp or wet locations. There
is a risk of electric shock!
• Keep work area well lit.
•
liquids or gases. There is a risk of explosion!
2. Store idle product
• When not in use, the product should be stored in a dry
locked-up place, out of reach of children.
3. Do not overload the product
• It will do the job better and safer at the rate for which
it was intended.

EN
04
TTB772STM by TITAN
Getting started...
Technical and legal information
Safety warnings
4. Do not abuse the cord
• Never yank the cord to disconnect it from the socket.
Keep the cord away from heat, oil and sharp edges.
5. Disconnect the product
• When not in use, before servicing and when changing
accessories for the attachment tool, disconnect the
product from the power supply.
6. Stay alert
• Watch what you are doing, use common sense and do
not operate the product when you are tired.
7. Check damaged parts
• Before further use of the product, it should be carefully
checked to determine that it will operate properly and
perform its intended function.
8. Don’t use unauthorized parts
• The use of any accessory or attachment other than
one recommended in this instruction manual may
present a risk of personal injury.
9.
• This electric product complies with the relevant safety
persons using original spare parts; otherwise this may
result in considerable danger to the user.
Wallpaper stripper safety warnings
1. Never direct steam towards people, pets, yourself or
equipment with electrical components, such as the
interior of ovens.
2. Never leave the product unattended when it is
connected to the power supply. Keep the product out
of reach of children while it is connected to power
supply or cooling down.

EN
TTB772STM by TITAN
Getting started...
05
Technical and legal information
3. Do not use the product if it has been dropped, if there
are visible signs of damage or leakage.
4. Do not remove the safety cap during use. Always allow
the water tank to cool down for at least 3 minutes after
use before attempting to remove the safety cap.
5. Keep the product out of reach of children.
6. The surfaces of product will get hot during use. Handle
carefully.
7. Do not use outside in adverse weather conditions or
allow the water tank to be exposed to rain or moisture.
The use of a 30mA high sensitivity residual circuit
breaker (RCD) is recommended for outdoor use or
around the home.
8. Do not cover the safety cap during use. Openings
in the safety cap allow release of excess steam and
pressure.
9. Disconnect the product from the power supply after
use and before cleaning, maintenance, storage and
transportation. Allow the product to cool down before
handling.
10. Protect the electrical parts against moisture. Do not
immerse such parts in water or other liquids to avoid
electrical shock. Never hold the product under running
water. Read the instructions provided in the chapter
“Care and Maintenance”.
11. Fill the product with water before each use so that
the water level reaches between the MIN and MAX
water level exceeds MAX level. Never connect the
product to power supply while empty.
12.
surface. Operating the product in any other position
could cause a hazard. Do not tilt and / or overturn the
product during its operation. If the product is tipped on
its side, return it back onto its feet immediately.

EN
06
TTB772STM by TITAN
Getting started...
Technical and legal information
Safety warnings
13. Never touch the plug and / or socket with wet hands.
14. Do not step on or place items on the water tank or
hose.
15. Never use the steam plate directly above your head as
boiling water may drip from the plate. Empty the steam
plate regularly as hot water may drip.
16. If working on a ladder, do not overreach and secure
the product properly to avoid any safety hazard.
17. Keep tight grip on the handles / grip surface.
18. Always carry the product by its handle. Never pull the
product on the power cord or hose.
19. Cover sockets, switches and wood surfaces before
operation to avoid damage by steam.
20. Do not use on glass surfaces as steam may cause
glass to shatter.
21. Do not immerse the water tank in water or any other
liquid.
22. Even though the hose has a double wall to reduce
the risk of burning if touched or grabbed, water tank,
steam plate and hose will get hot during use. Allow
attachments to cool down before removing or changing
them.
23. If using an extension lead, ensure you do not exceed
the maximum rated running wattage / load of the
extension lead.
24. Before connecting the product, ensure the mains
plate.
25. As this is a high power product, the plug could get
warm during use. This is normal and should not reach
excessive levels.
26. Only use the product as intended by its design and
these instructions.

EN
TTB772STM by TITAN
Getting started...
07
Technical and legal information
27. Ensure that the product is in good condition and well
maintained.
28. Use correct attachments for the product and ensure
they are in good condition.
29. Never put descaling, aromatic, alcoholic or detergent
products into the water tank, as this can damage the
product or make it unsafe for use.
WARNING! This product produces an
may under some circumstances interfere with
active or passive medical implants! To reduce
the risk of serious or fatal injury, we recommend
persons with medical implants to consult their
doctor and the medical implant manufacturer
before operating this product!
Symbol explanation
others the following symbols and abbreviations. Familiarise yourself with them to
reduce hazards like personal injuries and damage to property.
V~ Volt, (alternating voltage) W Watt
Hz Hertz m Metre
mm Millimetre kg Kilogram
l Litre °C Degree Celsius
Protective earth
yyWxx Manufacturing date code; year of manufacturing (20yy) and week of
manufacturing (Wxx).
IPX4 Protection against splashing water from all directions.
Lock / to tighten or secure.
Unlock / to loosen.

EN
08
TTB772STM by TITAN
Technical and legal information
Getting started...
Symbol explanation
Note / Remark.
Caution / Warning.
Read the instruction manual.
WARNING! Beware of electric shocks.
Wear eye protection.
Wear protective gloves.
Switch the product off and disconnect it from the power supply
before assembly, cleaning, adjustments, maintenance, storage and
transportation.
WARNING! Danger of scalding. Steam may escape from the
pressure release valve during and after use.
Do not expose the product to rain or wet conditions.
The product complies with the applicable European directives and
an evaluation method of conformity for these directives was done.
WEEE symbol. Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check
with your Local Authority or local store for recycling advice.
Keep your hands away!

EN
TTB772STM by TITAN
Getting started...
09
Your product
Product description
21 2a
5
5a
4
6
5a
3b
3a
3c
1. Safety cap
2. Carry handle
a. Lock button
3. Steam plate
a. Hose connector*
b. Apron
c. Handle
4. Water tank
a. Heating element*
b. Socket*
c. Water level indicator
(MIN / MAX)*
d. Hose connector*
5. Hose
a. Hose adaptor (x2)
6. Power cord
NOTE: Parts marked with * are not shown in this overview. Please
refer to the respective section in the instruction manual.

EN TTB772STM by TITAN
Getting started...
10
General
> Rated voltage, frequency : 230-240 V~, 50 Hz
> Rated power input : 2000 W
> Degree of protection : IPX4
> Protection class : I
> Tank capacity : 4 l
> Hose length : 3 m
> Dimensions : 325 x 250 x 255 mm
> Weight : Approx. 2 kg
Rating label explanation
TTB772STM
TT = TITAN
B = 240 V AC
772 = Version number
STM = Wallpaper stripper
Unpacking
>
> Remove all packing materials and shipping devices, if applicable.
> Make sure the delivery contents are complete and free of any damage. If you
your dealer. Using an incomplete or damaged product represents a hazard to
people and property.
> Ensure that you have all the accessories and tools needed for assembly and
operation. This also includes suitable personal protective equipment.
WARNING! The product and the packaging are not children’s toys!
Children must not play with plastic bags, sheets and small parts!
There is a danger of choking and suffocation!

EN
TTB772STM by TITAN
Getting started...
Before you start
11
You will need
(Items not supplied)
Suitable personal protective equipment
Scraper
(Items supplied)
Steam plate (3)
Water tank (4)
Hose (5)
Assembly
WARNING! The product must be fully assembled before operation!
Do not use a product that is only partly assembled or assembled with
damaged parts!
Follow the assembly instructions step-by-step and use the pictures
provided as a visual guide to easily assemble the product!
NOTE:
Attaching the hose
> Screw one hose adaptor (5a) to the hose connector (4d) of the water tank (4) in
a clockwise direction. Ensure the connection is properly secured (Fig. 1).
> Press down the lock button (2a) and remove the steam plate (3) from the carry
handle (2) (Fig. 2).
4
5a
4d
1.
2.
Fig. 1
2
2a
3
1.
2.
Fig. 2
> Grasp the steam plate handle (3c) and slide the steam plate (3) out of the track
of steam plate apron (3b) (Fig. 3).
> Screw the other hose adaptor (5a) to the hose connector (3a) of the steam plate
(3) in a clockwise direction. Ensure the connection is properly secured (Fig. 4).

EN TTB772STM by TITAN
Before you start
Getting started...
12
Assembly
3c
3b
3
Fig. 3
3
3a
5a
1.
2.
Fig. 4
WARNING! Do not use this product with a damaged hose (5) or
steam plate (3)!
Check that both hose connectors (3a, 4d) on the steam plate (3) and
water tank (4) are free of damage before assembly.
> Slide the steam plate (3) back into the track of steam plate apron (3b). Ensure
the hose (5) is not squeezed by the steam plate apron (3b) (Fig. 5).
> The hose (5) is now assembled (Fig. 6).
3b
5
3
Fig. 5
5
Fig. 6
Detaching the hose
WARNING! Disconnect the product from the power supply and wait
for it to cool down before removing any part. There is a risk of scalding
with hot water / steam.

EN
TTB772STM by TITAN
Getting started...
13
Before you start
> After use, once the product has cooled down, unscrew both hose adaptors (5a)
in an anti-clockwise direction from the steam plate (3) and water tank (4) hose
connectors (3a, 4d).
NOTE: Slightly unscrew the safety cap (1), once the product has
cooled down. If it triggers a jet of steam, the water tank (4) is still under
pressure. Wait 15 minutes before checking again and attempting to
disassemble the product.
Filling with water
WARNING!
power supply and wait for 15 minutes before adding water into the
water tank (4). There is a risk of scalding with steam and / or hot
water.
The water tank (4) has a capacity of 4 liters. Fill the water tank (4) as follows:
>
stable and heat-resistant surface.
> Unscrew the safety cap (1) in an anti-clockwise direction and remove it from the
water tank (4) (Fig. 7).
> Pour water into the water tank (4) until the water level reaches between the MIN
and MAX markings on the water level indicator (4c) (Fig. 8). Use a proper funnel
MAX level.
1
4
Fig. 7
1
4c 4
Fig. 8
MNL_MWPS2000_DFT_MAC_ Wallpaper Stripper_GB_V1_200818.indd 13 8/18/20 3:56 PM

EN TTB772STM by TITAN
Before you start
Getting started...
14
Filling with water
> Screw the safety cap (1) back onto the water tank (4). Do not overtighten.
NOTE:
reduce lime scale deposits.
It is not necessary to use distilled water.
It is possible to shorten the preheat time by adding hot water, but
never pour boiling water into the tank.
Connection to power supply
> Ensure the water level in the water tank (4) is located between the MIN and
MAX markings.
> Plug the adaptor of the power cord (6) into the water tank socket (4b) (Fig. 9).
4
4b
6
Fig. 9
> Connect the plug of power cord (6) to a suitable mains socket.
WARNING! Check the voltage! The voltage must comply with the
information on the rating label!
Always use a residual current device (RCD) protected supply.
NOTE: This unit will automatically begin the boiling process when
power is switched on at the mains socket.
> Your product is now ready to be used.
NOTE: During preheat time, do not leave the steam plate facing down
and always place it in a suitable container (bucket/trough). Escaping
steam could damage surfaces.
Never leave the product unattended while it is connected to the power
supply or cooling down. Keep children and pets at safe distance.

EN
TTB772STM by TITAN
15
In more detail...
In more
detail...
23
24
25
19
17
16
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee

EN
16
EN
In more detail...
TTB772STM by TITAN
Product functions
Intended use
This wallpaper stripper TTB772STM is designated with a nominal power of
2000 Watts.
This product is intended for wallpaper stripping and can also be used for some
cleaning tasks.
The product must never be left unattended while it is connected to power supply
or cooling down.
operation and to observe all the instructions therein.
Pressure release valve
The safety cap (1) is equipped with a pressure release valve.
When the pressure inside the water tank (4) reaches its maximum level, the valve
automatically releases pressure and steam escapes from the openings on top of
the safety cap. If this happens, check that the hose is not twisted or kinked. This
will stop once pressure level inside the tank decreases to suitable levels.
WARNING: Danger of scalding. Steam may escape from the pressure
release valve during and after use.
Thermal cut-out
The water tank socket (4b) is equipped with a thermal cut-out. In the event that
the product becomes overheated due to low or no water, the thermal cut-out
automatically switches the product off. After a cooling period the product resets
and automatically switches on again.
WARNING! Disconnect the product from the power supply if the
thermal protection is activated and before removing any parts. There
is a risk of scalding with hot water / steam.
> Inspect the product for water level, possible damage, wear or foreign objects
that block the steam plate (3) / hose (5).
> Eliminate the cause and wait 15 minutes prior to plugging the product again
(see “Troubleshooting”).

EN
17
EN
In
more
detail...
TTB772STM by TITAN Product functions / Operation
NOTE: Should the thermal protection continuously be activated even
after following the steps under “Troubleshooting”, do not use the
WARNING! The product is not designed for continuous use. Let it
rest for 15 minutes after each hour of running.
General operation
> Check the product, its power cord and plug as well as accessories for damage
before each use. Do not use the product if it is damaged or shows wear.
>
> Always hold the product on its handles. Keep the handles dry to ensure safe
support.
> Ensure openings on the safety cap (1) are always unobstructed and clear. Clean
them if necessary with a soft brush. Blocked openings may lead to overheating,
overpressure and damage the product.
> Disconnect the product from the power supply immediately if you are disturbed
while working by other people entering the working area. Never leave the
product unattended while it is connected to power supply or cooling down.
NOTE: Before initial start and at each re-start, check the water level
in the water tank (4). Add water into the water tank (4) if necessary
and reconnect the product (see “Filling with water”).
Make sure the hose connection is properly secured and the product
Even though the hose (5) has a double wall to reduce risks of burn
if touched or grabbed the steam plate (3), water tank (4) and hose
(5) will get hot during use. Allow the product and attachments to cool
down before removing or changing them.
Stripping
WARNING! Check the walls and / or ceilings before operation. If the
material is damaged, loose or seems fragile, consider not using the
product to avoid further damage caused by steam and water.
Test the product on a small area before operation.
>
8/18/20 3:56 PM

EN
18
EN Operation
In more detail...
TTB772STM by TITAN
Stripping
NOTE: Place a suitable element, such as a wooden board, under the
product to avoid marking and / or damaging the surface due to heat
generated by the product.
> Ensure the water level in the water tank (4) is located between the MIN and
MAX markings and then connect the product to power supply.
> While the product preheats, score the wallpaper with a suitable tool, such as a
wallpaper scorer or a scraper.
WARNING! Wear protective gloves and safety glasses during
operation.
Always grasp the steam plate by its handle (3c) and keep the steam
plate (3) at arm length to avoid burns due to escaping steam.
Do not direct steam towards yourself or others.
> The product is ready when the water is boiling and steam escapes from the
steam plate (3). Hold the steam plate by its handle (3c) and apply against the
work area (Fig. 10).
3
3c
Fig. 10
> After 10 seconds, move the steam plate (3) to the area next to the one you
steamed. Use a scraper to lift / remove the piece of wallpaper you steamed.
NOTE:
plate (3) a few more seconds on each area.
Alternatively, spray the scored wallpaper with water and let soak for
10 minutes before applying steam.

EN
19
EN
In
more
detail...
TTB772STM by TITAN Operation / Care and maintenanceOperation / Care and maintenance
> Keep working along the strip of wallpaper until it can be completely removed
from the wall.
> Repeat above steps until all wallpaper strips have been removed from the walls.
NOTE: The product is not designed for continuous use. Disconnect
it from the power supply and let it rest for 15 minutes after each hour
of running.
80 minutes of use. Check the
water level regularly during use and ensure it does not reach below
the MIN marking. Add water if necessary (See “Filling with water”).
After use
> Disconnect the product from the power supply to switch it off, unplug the power
cord from the product and let it cool down.
> Check, clean and store the product as described below.
The golden rules for care
WARNING! Always disconnect the product from the power supply and
let the product cool down before performing inspection, maintenance
and cleaning work!
> Keep the product clean. Remove debris from it after each use and before
storage.
> Regular and proper cleaning will help ensure safe use and prolong the life of
the product.
> Inspect the product before each use for worn and damaged parts. Do not
WARNING! Only perform repairs and maintenance work according to
specialist!

EN
20
EN
In more detail...
TTB772STM by TITAN
Care and maintenance
General cleaning
> Clean the product with a dry cloth. Use a brush for areas that are hard to reach.
NOTE: Do not use chemical, alkaline, abrasive or other aggressive
detergents or disinfectants to clean this product as they might be
harmful to its surfaces.
> Check for worn or damaged parts. Replace worn parts as necessary or contact
an authorised service centre for repair before using the product again.
Maintenance
Before and after each use, check the product and accessories (or attachments)
for wear and damage. If required, exchange them for new ones as described in
this instruction manual. Observe the technical requirements.
Lime scale removal
From time to time – according to the nature of your tap water – calcium deposits
form in the product and accessories. The strength of the deposits (and thus the
frequency of removal) depends upon the degree of hardness of the water and
how often the product is used. Check with your local water company in order to
NOTE: Use a mixture of water and citric acid or vinegar for lime
scale removal. These substances are readily biodegradable and
environmentally friendly!
> Make a mixture of one part of vinegar and two parts water in a suitable container,
e. g. in a bucket.
> Fill the water tank (4) with the mixture.
> Connect the product to the power supply and let it heat up for 15 minutes.
> Disconnect the product from the power supply and leave the mixture in the tank
for approximately 1 hour.
> Then empty the tank and rinse with clear water to remove residues.
NOTE: Rinse the water tank (4) with 1 litre of water after each use to
reduce lime scale formation.