Titan TTB926STM User manual
Original Instructions_MNL_TTB926STM_GB_V8_220623
TTB926STM
2200W Wallpaper
Stripper
WARNING! Read the instructions before using the product!
EN
V80623 / BX220IM
EAN: 5059340400082
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 1MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 1 2022/6/23 下午5:042022/6/23 下午5:04
EN
02
24
25
26
22
19
17
16
In more detail...
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
Declaration of conformity
15
02
03
08
08
10
Getting started...
Technical and legal information
Your product
Technical specications
Before you start
These instructions are for your safety. Please read through them
thoroughly before use and retain them for future reference.
Let’s
get started...
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 2MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 2 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
03
EN
Technical and legal information
Safety warnings
1. This appliance can be used by persons with reduced
physical, sensory or mental capabilities or lack of
experience and knowledge if they have been given
supervision or instruction concerning use of the
appliance in a safe way and understand the hazards
involved.
2. Children shall not play with the appliance.
General safety warnings
WARNING! When using electric products basic
safety precautions should always be followed to
reduce the risk of re, electric shock and personal
injury including the following.
Read all these instructions before attempting to
operate this product and save all warnings and
instructions for future reference.
Safe operation
1. Consider work area environment
• Do not expose the product to rain.
• Do not use the product in damp or wet locations.
There is a risk of electric shock!
• Keep work area well lit.
• Do not use the product in the presence of ammable
liquids or gases. There is a risk of explosion!
2. Store idle product
• When not in use, the product should be stored in a
dry locked-up place, out of reach of children.
3. Do not overload the product
• It will do the job better and safer at the rate for which
it was intended.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 3MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 3 2022/6/23 下午5:042022/6/23 下午5:04
04
TTB926STM by TITAN
Getting started...
EN
Technical and legal information
Safety warnings
4. Do not abuse the cord
• Never yank the cord to disconnect it from the socket.
Keep the cord away from heat, oil and sharp edges.
5. Disconnect the product
• When not in use, before servicing and when changing
accessories for the attachment tool, disconnect the
product from the power supply.
6. Stay alert
• Watch what you are doing, use common sense and
do not operate the product when you are tired.
7. Check damaged parts
• Before further use of the product, it should be carefully
checked to determine that it will operate properly and
perform its intended function.
8. Don’t use unauthorized parts
• The use of any accessory or attachment other than
one recommended in this instruction manual may
present a risk of personal injury.
9. Have your product repaired by a qualied person
• This electric product complies with the relevant safety
rules. Repairs should only be carried out by qualied
persons using original spare parts; otherwise this
may result in considerable danger to the user.
Wallpaper stripper safety warnings
1. Do not leave the product switched on and unattended
whilst children and pets are around.
2. Do not stand directly underneath the steam plate when
in use.
3. Do not switch the product on before lling with water.
4. Do not overll the water above the maximum level.
5. Do not tilt the water tank when in use.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 4MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 4 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
05
EN
Technical and legal information
6. Do not rell immediately after use. Please wait at least
15 minutes before relling with water.
7. Never direct steam towards people, pets, yourself or
equipment with electrical components, such as the
interior of ovens.
8. Never leave the product unattended when it is
connected to the power supply. Keep the product out
of reach of children while it is connected to power
supply or cooling down.
9. Do not use the product if it has been dropped, if there
are visible signs of damage or leakage.
10. Do not remove the safety cap during use. Always allow
the water tank to cool down for at least 15 minutes
after use before attempting to remove the safety cap.
11. Keep the product out of reach of children.
12. The surfaces of product will get hot during use. Handle
carefully.
13. Do not use outside in adverse weather conditions or
allow the water tank to be exposed to rain or moisture.
The use of a 30mA high sensitivity residual circuit
breaker (RCD) is recommended for outdoor use or
around the home.
14. Do not cover the safety cap during use. Openings
in the safety cap allow release of excess steam and
pressure.
15. Disconnect the product from the power supply after
use and before cleaning, maintenance, storage and
transportation. Allow the product to cool down before
handling.
16. Protect the electrical parts against moisture. Do not
immerse such parts in water or other liquids to avoid
electrical shock. Never hold the product under running
water. Read the instructions provided in the chapter
“Care and Maintenance”.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 5MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 5 2022/6/23 下午5:042022/6/23 下午5:04
06
TTB926STM by TITAN
Getting started...
EN
Technical and legal information
Safety warnings
17. Fill the product with water before each use so that
the water level reaches between the MIN and MAX
markings. Do not overll. Drain the water tank if the
water level exceeds MAX level. Never connect the
product to power supply while empty.
18. Place the product on a at, stable, heat-resistant
surface. Operating the product in any other position
could cause a hazard. Do not tilt and / or overturn the
product during its operation. If the product is tipped on
its side, return it back onto its feet immediately.
19. Never touch the plug and / or socket with wet hands.
20. Do not step on or place items on the water tank or
hose.
21. Never use the steam plate directly above your head as
boiling water may drip from the plate. Empty the steam
plate regularly as hot water may drip.
22. If working on a ladder, do not overreach and secure
the product properly to avoid any safety hazard.
23. Keep tight grip on the handles / grip surface.
24. Always carry the product by its handle. Never pull the
product by the power cord or hose.
25. Cover sockets, switches and wood surfaces before
operation to avoid damage by steam.
26. Do not use on glass surfaces as steam may cause
glass to shatter.
27. Do not immerse the water tank in water or any other
liquid.
28. Even though the hose has a double wall to reduce
the risk of burning if touched or grabbed, water tank,
steam plate and hose will get hot during use. Allow
attachments to cool down before removing or changing
them.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 6MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 6 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
07
EN
Technical and legal information
29. If using an extension lead, ensure you do not exceed
the maximum rated running wattage / load of the
extension lead.
30. Before connecting the product, ensure the mains
voltage available matches that specied on the rating
plate.
31. As this is a high power product, the plug could get
warm during use. This is normal and should not reach
excessive levels.
32. Only use the product as intended by its design and
these instructions.
33. Ensure that the product is in good condition and well
maintained.
34. Use correct attachments for the product and ensure
they are in good condition.
35. Never put descaling, aromatic, alcoholic or detergent
products into the water tank, as this can damage the
product or make it unsafe for use.
WARNING! This product produces an
electromagnetic eld during operation! This eld
may under some circumstances interfere with
active or passive medical implants! To reduce
the risk of serious or fatal injury, we recommend
persons with medical implants to consult their
doctor and the medical implant manufacturer
before operating this product!
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 7MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 7 2022/6/23 下午5:042022/6/23 下午5:04
08
TTB926STM by TITAN
Your product / Technical specications
Getting started...
EN
Product description
1. Safety cap
2. Carry handle
a) Lock button
3. Steam plate
a) Hose connector*
b) Apron
c) Handle
4. Water tank
a) Heating element*
b) Socket*
c) Water level
indicator (MIN / MAX)
d) Hose connector*
5. Hose
a) Hose adaptor (x2)
6. Power cord
7. Scraper
NOTE: Parts marked with * are not shown in this overview. Please
refer to the respective section in the instruction manual.
Technical specications
General
> Rated voltage, frequency : 220-240 V~, 50 Hz
> Rated power input : 2200 W
> Degree of protection : IPX4
> Protection class : I
> Tank capacity : 6.5 L
> Hose length : 4 m
> Dimensions : 388x224x302 mm
> Weight : Approx. 2.5 kg
2
4c 4
3
3b
5
2a 5a
7
3c
6
1
5a
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 8MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 8 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
Technical specications
EN
9
Rating label explanation
Wallpaper Stripper: TTB926STM
TT = TITAN
B = Voltage (220-240 V~)
926 = Series number
STM = Steam wallpaper stripper
Symbol explanation
On the product, the rating label and within these instructions you will nd among
others the following symbols and abbreviations. Familiarise yourself with them to
reduce hazards like personal injuries and damage to property.
V~ Volt, (alternating voltage) W Watt
Hz Hertz m Metre
mm Millimetre kg Kilogram
L Litre °C Degree Celsius
Protective earth
Lock / to tighten or secure. Unlock / to loosen.
Note / Remark. Caution / Warning.
yyWxx Manufacturing date code; year of manufacturing (20yy) and week of
manufacturing (Wxx).
IPX4 Protection against splashing water from all directions.
Read the instruction manual.
WARNING! Beware of electric shocks.
Wear eye protection.
Wear protective gloves.
Switch the product off and disconnect it from the power supply
before assembly, cleaning, adjustments, maintenance, storage and
transportation.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 9MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 9 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
EN
10
Technical specications / Before you start
Symbol explanation
WARNING! Danger of scalding. Steam may escape from the pressure
release valve during and after use.
Do not expose the product to rain or wet conditions.
The product complies with the applicable European directives and an
evaluation method of conformity for these directives was done.
UK Conformity Assessed.
WEEE symbol. Waste electrical products should not be disposed of
with household waste. Please recycle where facilities exist. Check with
your Local Authority or local store for recycling advice.
Unpacking
1. Unpack all parts and lay them on a at, stable surface.
2. Remove all packing materials and shipping devices, if applicable.
3. Make sure the delivery contents are complete and free of any damage. If
you nd that parts are missing or show damage do not use the product but
contact your dealer. Using an incomplete or damaged product represents a
hazard to people and property.
4. Ensure that you have all the accessories and tools needed for assembly and
operation. This also includes suitable personal protective equipment.
WARNING! The product and the packaging are not children’s toys!
Children must not play with plastic bags, sheets and small parts! There
is a danger of choking and suffocation!
You will need
(Items not supplied)
Suitable personal protective equipment
(Items supplied)
Steam plate (3)
Water tank (4)
Hose (5)
Scraper (7)
NOTE: The accessories required depend on the intended application.
Ask your dealer for advice.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 10MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 10 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
EN
11
Before you start
Assembly
WARNING! The product must be fully assembled before operation!
Do not use a product that is only partly assembled or assembled with
damaged parts!
Follow the assembly instructions step-by-step and use the pictures
provided as a visual guide to easily assemble the product!
NOTE: Always lay the product with its feet on a at, stable surface.
Attaching the hose
1. Screw one hose adaptor (5a) clockwise onto the thread of the hose connector
(4d) of the water tank (4). Ensure the connection is properly secured (Fig. 1).
2. Press down the lock button (2a) and remove the steam plate (3) from the
carry handle (2) (Fig. 2).
5a
4
4d
2.
1.
Fig. 1
2
3
2a
2.
1.
Fig. 2
3. Grasp the steam plate handle (3c) and slide the steam plate (3) out of the
track of steam plate apron (3b) (Fig. 3).
4. Screw the other hose adaptor (5a) clockwise onto the thread of the hose
connector (3a) of the steam plate (3). Ensure the connection is properly
secured (Fig. 4).
3b
3
Fig. 3
5
3
2.
1.
Fig. 4
3c
5a
3a
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 11MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 11 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
EN
12
Assembly
WARNING! Do not use this product with a damaged hose (5) or steam
plate (3)!
Check that both hose connectors (3a, 4d) on the steam plate (3) and
water tank (4) are free of damage before assembly.
5. Slide the steam plate (3) back into the track of steam plate apron (3b). Ensure
the hose (5) is not squeezed by the steam plate apron (3b) (Fig. 5).
6. The hose (5) is now assembled (Fig. 6).
5
3
Fig. 5
5
Fig. 6
Detaching the hose
WARNING! Disconnect the product from the power supply and wait
for it to cool down before removing any part. There is a risk of scalding
with hot water / steam.
1. After use, once the product has cooled down, unscrew the two hose adaptors
(5a) anti-clockwise from the threads of the hose connectors (3a, 4d) on the
steam plate (3) and water tank (4).
NOTE: Slightly unscrew the safety cap (1), once the product has
cooled down. If it triggers a jet of steam, the water tank (4) is still under
pressure. Wait 15 minutes before checking again and attempting to
disassemble the product.
Before you start
3b
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 12MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 12 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
EN
13
Filling with water
WARNING! When relling with water during use, disconnect from the
power supply and wait for 15 minutes before adding water into the
water tank (4). There is a risk of scalding with steam and / or hot water.
The water tank (4) has a capacity of 6.5 litres. Fill the water tank (4) as follows:
1. Ensure the product is disconnected from the power supply and placed on a
at, stable and heat-resistant surface.
2. Unscrew the safety cap (1) anti-clockwise and remove it from the water tank
(4) (Fig. 7).
3. Pour water into the water tank (4) until the water level reaches between the
MIN and MAX markings on the water level indicator (4c) (Fig. 8). Use a funnel
if necessary. Do not overll. Drain the water tank (4) if the water level exceeds
MAX level.
4
1
Fig. 7
4
4c
Fig. 8
4. Screw the safety cap (1) back onto the water tank (4). Do not overtighten.
NOTE: Before relling, rinse the water tank (4) with 1 litre of water rst
to reduce lime scale deposits.
It is not necessary to use distilled water.
It is possible to shorten the preheat time by adding hot water, but never
pour boiling water into the water tank (4).
Before you start
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 13MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 13 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
Getting started...
EN
14
Connection to power supply
1. Ensure the water level in the
water tank (4) is located between
the MIN and MAX markings.
2. Insert the power adaptor of the
power cord (6) into the water
tank socket (4b) (Fig. 9). Ensure
they are properly engaged.
3. Connect the plug of power cord
(6) to a suitable mains socket.
4
4b
Fig. 9
WARNING! Check the voltage! The voltage must comply with the
information on the rating label!
Always use a residual current device (RCD) protected supply.
NOTE: This unit will automatically begin the boiling process when
power is switched on at the mains socket.
4. Your product is now ready to be used.
NOTE: During preheat time, do not leave the steam plate (3) facing
down and always place it in a suitable container (bucket/trough).
Escaping steam could damage surfaces.
Never leave the product unattended while it is connected to the power
supply or cooling down. Keep children and pets at safe distance.
Before you start
6
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 14MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 14 2022/6/23 下午5:042022/6/23 下午5:04
TTB926STM by TITAN
15
In more detail...
In more
detail...
EN
22
24
25
26
19
17
16
Product functions
Operation
Care and maintenance
Troubleshooting
Recycling and disposal
Guarantee
Declaration of conformity
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 15MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 15 2022/6/23 下午5:042022/6/23 下午5:04
EN
16
Product functions
In more detail...
TTB926STM by TITAN
EN
Intended use
This wallpaper stripper TTB926STM is designated with a nominal power of
2200 Watts.
This product is intended for wallpaper stripping and can also be used for some
cleaning tasks.
The product must never be left unattended while it is connected to power supply
or cooling down.
The product is to be used only for its prescribed purpose. Any other use is deemed
to be a case of misuse.
For safety reasons it is essential to read the entire instruction manual before rst
operation and to observe all the instructions therein.
WARNING! Always disconnect the product from power supply and let
the product cool down before making adjustments to the product!
Pressure release valve
The safety cap (1) is equipped with a pressure release valve.
When the pressure inside the water tank (4) reaches its maximum level, the valve
automatically releases pressure and steam escapes from the openings on top of
the safety cap (1). If this happens, check that the hose (5) is not twisted or kinked.
This will stop once pressure level inside the water tank (4) decreases to suitable
levels.
WARNING! Danger of scalding. Steam may escape from the pressure
release valve during and after use.
Thermal cut-out
The water tank socket (4b) is equipped with a thermal cut-out. In the event that
the product becomes overheated due to low or no water, the thermal cut-out
automatically switches the product off. After a cooling period the product resets
and automatically switches on again.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 16MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 16 2022/6/23 下午5:042022/6/23 下午5:04
EN
17
In more detail...
TTB926STM by TITAN
Product functions / Operation
EN
WARNING! Disconnect the product from the power supply if the
thermal protection is activated and before removing any parts. There is
a risk of scalding with hot water / steam.
1. Inspect the product for water level, possible damage, wear or foreign objects
that block the steam plate (3) / hose (5).
2. Eliminate the cause and wait 15 minutes prior to plugging the product again
(see “Troubleshooting”).
NOTE: Do not use the product if the thermal protection continuously
activates even after following the steps under “Troubleshooting”. Have
it checked and repaired by a qualied specialist.
WARNING! The product is not designed for continuous use. Let it rest
for 15 minutes after each hour of running.
General operation
1. Check the product, its power cord and plug as well as accessories for damage
before each use. Do not use the product if it is damaged or shows wear.
2. Double check that the accessories and attachments are properly xed.
3. Always hold the product on its handles. Keep the handles dry to ensure safe
support.
4. Ensure openings on the safety cap (1) are always unobstructed and clear.
Clean them if necessary with a soft brush. Blocked openings may lead to
overheating, overpressure and damage the product.
5. Disconnect the product from the power supply immediately if you are disturbed
while working by other people entering the working area. Never leave the
product unattended while it is connected to power supply or cooling down.
NOTE: Before initial start and at each re-start, check the water level in
the water tank (4). Add water into the water tank (4) if necessary and
reconnect the product (see “Filling with water”).
Make sure the hose connection is properly secured and the product is
placed on a at surface.
Even though the hose (5) has a double wall to reduce risks of burn if
touched or grabbed the steam plate (3), water tank (4) and hose (5)
will get hot during use. Allow the product and attachments to cool down
before removing or changing them.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 17MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 17 2022/6/23 下午5:042022/6/23 下午5:04
EN
18
Operation
In more detail...
TTB926STM by TITAN
EN
Stripping
WARNING! Check the walls and / or ceilings before operation. If the
material is damaged, loose or seems fragile, consider not using the
product to avoid further damage caused by steam and water.
Test the product on a small area before operation.
1. Place the product on its feet on a at, stable, heat-resistant surface.
NOTE: Place a suitable element, such as a wooden board, under the
product to avoid marking and / or damaging the surface due to heat
generated by the product.
2. Ensure the water level in the water tank (4) is located between the MIN and
MAX markings and then connect the product to power supply.
3. While the product preheats, score the wallpaper with a suitable tool, such as
a wallpaper scorer or a scraper (7).
WARNING! Wear protective gloves and safety glasses during
operation.
Always grasp the steam plate (3) by its handle (3c) and keep the steam
plate (3) at arms length to avoid burns due to escaping steam.
Do not direct steam towards yourself or others.
4. The product is ready when the water
is boiling and steam escapes from the
steam plate (3). Hold the steam plate by
its handle (3c) and apply to the work area
(Fig. 10).
5. After 10 seconds, move the steam
plate (3) to the area next to the one you
steamed. Use the supplied scraper (7) to
lift / remove the piece of wallpaper you
steamed.
3
3c
Fig. 10
NOTE: If the wallpaper proves difcult to remove, leave the steam
plate (3) a few more seconds on each area.
Alternatively, spray the scored wallpaper with water and let soak for
10 minutes before applying steam.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 18MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 18 2022/6/23 下午5:042022/6/23 下午5:04
EN
19
In more detail...
TTB926STM by TITAN
Operation / Care and maintenance
EN
6. Keep working along the strip of wallpaper until it can be completely removed
from the wall.
7. Repeat above steps until all wallpaper strips have been removed from the
walls.
NOTE: The product is not designed for continuous use. Disconnect it
from the power supply and let it rest for 15 minutes after each hour of
running.
The max volume of water is sufcient for 80 minutes of use. Check the
water level regularly during use and ensure it does not reach below the
MIN marking. Add water if necessary (See “Filling with water”).
After use
1. Disconnect the product from the power supply to switch it off, unplug the
power cord from the product and let it cool down.
2. Check, clean and store the product as described below.
The golden rules for care
WARNING! Always disconnect the product from the power supply and
let the product cool down before performing inspection, maintenance
and cleaning work!
1. Keep the product clean. Remove debris from it after each use and before
storage.
2. Regular and proper cleaning will help ensure safe use and prolong the life of
the product.
3. Inspect the product before each use for worn and damaged parts. Do not
operate it if you nd broken and worn parts.
WARNING! Only perform repairs and maintenance work according to
these instructions! All further works must be performed by a qualied
specialist!
General cleaning
1. Clean the product with a dry cloth. Use a brush for areas that are hard to
reach.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 19MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 19 2022/6/23 下午5:042022/6/23 下午5:04
EN
20
In more detail...
TTB926STM by TITAN
EN
Care and maintenance
Power cord
If the power cord is damaged, it must be replaced by the manufacturer, its service
agent or similarly qualied persons in order to avoid a safety hazard.
UK plug
If you need to replace the tted plug, then follow the instructions below.
IMPORTANT: The wires in the mains lead are coloured in accordance with the
following code:
Blue – Neutral
Brown – Live
Green/Yellow - Earth
As the colours of the wire in the mains lead of this product may not correspond
with the coloured marking identifying the terminals in your plug, proceed as
follows. The wire, which is coloured blue, must be connected to the terminal,
which is marked with N or coloured black. The wire, which is coloured brown,
must be connected to the terminal, which is marked L or coloured red. The wire,
which is colored green/yellow,must be connected to the terminal, which is mark
E or .
WARNING! Never connect live or neutral wires to the earth terminal of
the plug, which is marked with E.
If you need to replace the fitted plug, then follow the instructions below.
IMPORTANT: The wires in the mains lead are coloured in accordance with the
following code:
Blue – Neutral
Brown – Live
Green/Yellow - Earth
As the colours of the wire in the mains lead of this product may not correspond
with the coloured marking identifying the terminals in your plug, proceed as
follows. The wire, which is coloured blue, must be connected to the terminal,
which is marked with N or coloured black. The wire, which is coloured brown,
must be connected to the terminal, which is marked L or coloured red. The wire,
which is colored green/yellow,must be connected to the terminal, which is mark E
or .
Only fit an approved BS 1363 or BS 1363/A plug and correctly rated BS 1362 13
Amp fuse. If in doubt, consult a qualified electrician.
UK plug
.
WARNING! Never connect live or neutral wires to the earth terminal of
the plug, which is marked with E.
NOTE: If a moulded plug is fitted and has to be removed take great
care in disposing of the plug and severed cable, it must be destroyed
to prevent engaging into a socket.
firmly clamped
13 AMP fuse approved
to BS 1362
Brown L (Live)
Cable grip
Outer sleeve
Connect Blue to N
Connect green/yellow wire
to E (Protective earth)
(Neutral)
Only t an approved BS 1363 or BS 1363/A plug and correctly rated BS 1362 13
Amp fuse. If in doubt, consult a qualied electrician.
NOTE: If a moulded plug is tted and has to be removed take great
care in disposing of the plug and severed cable, it must be destroyed
to prevent engaging into a socket.
General cleaning
NOTE: Do not use chemical, alkaline, abrasive or other aggressive
detergents or disinfectants to clean this product as they might be
harmful to its surfaces.
2. Check for worn or damaged parts. Replace worn parts as necessary or
contact an authorised service centre for repair before using the product again.
Maintenance
Before and after each use, check the product and accessories (or attachments)
for wear and damage. If required, exchange them for new ones as described in
this instruction manual. Observe the technical requirements.
Lime scale removal
From time to time – according to the nature of your tap water – calcium deposits
form in the product and accessories. The strength of the deposits (and thus the
frequency of removal) depends upon the degree of hardness of the water and
how often the product is used. Check with your local water company in order to
nd the hardness of the water in your area.
NOTE: Use a mixture of water and citric acid or vinegar for lime
scale removal. These substances are readily biodegradable and
environmentally friendly!
1. Make a mixture of one part of vinegar and two parts water in a suitable
container, e. g. in a bucket.
2. Fill the water tank (4) with the mixture.
3. Connect the product to the power supply and let it heat up for 15 minutes.
4. Disconnect the product from the power supply and leave the mixture in the
tank for approximately 1 hour.
5. Then empty the tank and rinse with clear water to remove residue.
NOTE: Rinse the water tank (4) with 1 litre of water after each use to
reduce lime scale formation.
MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 20MNL_TTB926STM_2200W Wallpaper Stripper_GB_V8_220623.indd 20 2022/6/23 下午5:042022/6/23 下午5:04
This manual suits for next models
1
Table of contents
Other Titan Tools manuals
