Titon CME2Q+ Owner's manual

PAGE 1OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Fault Finding
CME2Q+ Units With Live Switching
This document covers part numbers
TP304HA & TP305HA

PAGE 2OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Contents
Unit Identification.........................................................................................................................................................3
Product Features ..........................................................................................................................................................4
Setback Speed...........................................................................................................................................................4
Continuous Speed.....................................................................................................................................................4
Boost Speed with Overrun Timer .............................................................................................................................4
Boost Overrun Timer ................................................................................................................................................4
Integrated Humidity Sensor .....................................................................................................................................4
Wiring Diagrams ...........................................................................................................................................................5
PCB Configuration/Setting............................................................................................................................................5
Unit Dismantling...........................................................................................................................................................6
Fault Finding .................................................................................................................................................................7
Unit Not Running......................................................................................................................................................7
Unit Will Not Boost...................................................................................................................................................7
Unit Slows Down When Boosted..............................................................................................................................7
Unit Stuck In Boost ...................................................................................................................................................8
The unit is running at a speed that is not Continuous, Boost Or SetBack................................................................8
Excessive Unit/System Noise....................................................................................................................................8
Insufficient Airflow ...................................................................................................................................................8
Condensation/Mould Within House.........................................................................................................................9
Condensation/Moisture Forming In Or On Ducting .................................................................................................9
Unit Not Storing The Commissioning Settings..........................................................................................................9
Unit Will Not Stay In Place Without The Additional Fixing Screws...........................................................................9
Both Continuous and Boost Speeds Have Changed .................................................................................................9
Fig 1 Fan Mains & Low Voltage Molex Connector......................................................................................................10
Fig 2 PCB Fuse.............................................................................................................................................................10
Fig 3 Molex Connector................................................................................................................................................10
Fig 4 Programming Link ..............................................................................................................................................10
Fig 5 Boost & Setback Inputs ......................................................................................................................................10

PAGE 3OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Unit Identification
All maintenance/fault finding/repairs must be completed by a competent person.
Safe isolation procedures must be followed when working on these units.

PAGE 4OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Product Features
Model
CME2 Q Plus
Part Number
TP304HA
TP305HA
Complete Unit
●
2nd Fix Cover / Scroll / Inlet Ring
Assembly
●
Setback Speed
●
●
Continuous Speed
●
Boost Speed
●
Boost Overrun Timer
●
Integrated Humidity Sensor
●
●
Setback Speed
Setback Speed is a reduced ventilation rate. Setback Speed is configured using a step-less independent fan
control potentiometer. The Setback Speed can be enabled by connection of a volt-free one-way switch, or
combined with the Boost Speed with the 3 position switch TP 508.
Continuous Speed
Continuous Speed is the normal running speed of the unit. Continuous Speed is configured using a step-less
independent fan control potentiometer.
Boost Speed with Overrun Timer
Boost Speed is an increased speed providing higher extract air flow. Boost Speed is configured using a step-less
independent fan control potentiometer. The Boost Speed can be triggered by any device which provides a volt-
free one-way switch, such as a PIR, thermostat, humidistat or a standard one-way switch
Boost Overrun Timer
Boost Overrun Timer maintains the Boost Speed for a specific time variable between 0 and 30 minutes. The Boost
Overrun Timer time is configured using step-less independent potentiometer.
Integrated Humidity Sensor
There are two variations, the function slightly varies depending upon the software on the control PCB.
If the firmware on the PCB is FW0020-0100, then
This continuously monitors the relative humidity (RH) of the extracted air and triggers Boost Speed when the
relative humidity rises over the set threshold. The Humidity Sensor’s trigger point is variable from 55%RH to
85%RH and is configured using step-less independent potentiometer.
If the firmware on the PCB is FW0020-0200, then
This continuously monitors the relative humidity (RH) of the extracted air. The fan speed increases proportionally
between Continuous & Boost Speed depending on the measured %RH.
The Humidity Sensor’s set point is variable from 55%RH to 85%RH and is configured using a potentiometer.

PAGE 5OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Wiring Diagrams
PCB Configuration/Setting

PAGE 6OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Unit Dismantling
All maintenance/fault finding/repairs must be completed by a competent person.
Cover removal
Remove the screw adjacent to the cable entry
point, undo the remaining two screws, do not
remove the screws just undo sufficiently to
release the cover.
Caution This will then expose the control PCB
and mains terminal.
Inlet removal.
Remove the mains cable and the boost cable(s).
Safety lockout procedure must be followed prior
to disconnecting the mains from the unit.
Remove three additional fixing screws
Unclip the inlet ring from the first fix base. One
clip in each corner.
Scroll removal.
Undo the four screws, as shown.

PAGE 7OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Unclip the scroll in three places.
Fan removal
Disconnect the fan cables from the PCB and the
mains terminal, release the cable clamps. Then
remove the 4 retaining screws.
PCB removal
Disconnect the motor cable (white Molex connector) and the boost cables.
PCB is screwed in place –remove retaining screws.
N.B. the unit has a humidity sensor this protrudes under the PCB, take care when removing.
Fault Finding
Unit Not Running
1. How are you determining the fan is not running? The fan may be running but is so quiet it cannot
be herd.
oCheck flow rates at ceiling terminals
oIncrease fan speed, to see if it then becomes audible.
2. Check 230v is present at terminal block see wiring diagram & Fig 1.
3. Check molex connector is firmly located onto the PCB Fig 1.
4. Check the mains fuse Fig 2.
5. Check fan runs (connect a 10KΩ potentiometer as below to the fan connector), turning the
potentiometer will adjusts the fan speed from max to min or vice versa. See Fig 3
Unit Will Not Boost
1. Is it actually boosting but the boost speed is just higher or the same as continuous, therefore no
audible difference.
oCheck flow rates at continuous and boost to see if there is a difference.
oChange units speed to determine if difference is then audible.
Unit speeds can be determined by looking at the top of the
relevant potentiometer and seeing where the arrows point. If
the arrows on the continuous and boost pots are in the same
or similar positions the flow rates and noise will be similar.
Turning Anticlockwise –decrease speed
Turning Clockwise –increase speed
2. Is the unit in program position, the unit will not respond to boost or humidity when in the
programing position? The unit needs to be in the run position
3. Is the there 230V present across Neutral & LS1 Fig 5
Unit Slows Down When Boosted
1. Boost speed has been set lower than continuous, check set up.
2. Boost cable has been connected to set back terminal LS1.

PAGE 8OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Unit Stuck In Boost
Before commencing any checks complete the following:-
A. Make a note of where the overrun timer is set, then set to
minimum
B. Make a note of where the humidity is set, then set to maximum
C. Switch the unit off for 20 seconds, then back on.
Has this resolved the problem? If not:-
0 to 30
mins
55% to 85%
Hum.
1. Is the unit in program position, if the boost speed was the last speed set it will stay at that speed, fig 4.
2. Are all boost switches off
3. Is it actually dropping out of continuous but the boost speed is just higher or the same as continuous,
therefore no audible difference.
oCheck flow rates at continuous and boost to see if there is a difference.
oChange units speed to determine if difference is then audible.
4. Is the boost cabling providing a permanent live to the boost terminals?
oDisconnect the boost wire and safely terminate into another terminal block and switch the unit off for
20 seconds then restart.
5. Is there a leakage voltage on the switched live cable.
The unit is running at a speed that is not Continuous, Boost Or SetBack
1. Is the firmware on the PCB is FW0020-0200, if yes it is probable that the speed is ramping up/down due
to humidity.
Excessive Unit/System Noise
1. Is the unit providing the correct airflow, as calculated in Approved Document Part F? If set to high it may be
possible to slow down the fan, thus reducing noise.
2. Is the unit capable of achieving the required levels at an acceptable speed. The higher the speed the
greater the noise!
3. Is the unit permanently in boost?
4. Has the system been installed to the design?
5. Has the system been designed to minimise noise?
6. Is the ducting system fitted to minimise system resistance, including suitable external terminal, duct sizes
and duct type?
7. Is the ducting system sealed to minimise air leakage?
8. Is the unit correctly fitted to stop leakage? Have all fixing screws been fitted?
9. Is the Inlet Ring tight against the First Fix Base. If there is a gap it is likely that the two parts are not clipping
together correctly. Check the parts clip together correctly without the additional fixing screw. If they do not
clip together correctly it is possible the First Fix Base is twisted as it is not on a flat substrate.
10.Is there excessive noise from the fan/motor? E.g. bearing noise
Insufficient Airflow
1. Is the unit set to the correct flow rates i.e. commissioned?
2. Has the unit sufficient capacity for the dwelling requirements?
3. Has the system been installed to the design?
4. Is the design balanced?
5. Is there excessive resistance in the system?
6. Are the ceiling terminals closed?
7. Have the correct duct sizes been used?
8. Is the ducting system blocked/damaged?
9. Is there air leakage in the ducting system, is it sealed?
10.Is there air leakage from the unit?
11.Is there sufficient clearance under internal doors?
12.Is the unit correctly fitted to stop leakage? Have all fixing screws been fitted?

PAGE 9OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
13.Is the Inlet Ring tight against the First Fix Base. If there is a gap it is likely that the two parts are not clipping
together correctly. Check the parts clip together correctly without the additional fixing screw. If they do not
clip together correctly it is possible the First Fix Base is twisted as it is not on a flat substrate.
Condensation/Mould Within House
1. Is the unit being switched off, it must run 24/7
2. Where fitted, are trickle vents being left open?
3. Is the Boost function available and being used? N.B. not required in all properties depending upon
calculations.
4. Are flow rates being achieved?
oUnit not commissioned, N.B. standard rates may not be sufficient, dependent upon lifestyles.
oSystem is unable to provide sufficient air flow (refer to fault –insufficient air flow).
Condensation/Moisture Forming In Or On Ducting
oIs duct insulated as required, DVCG statement:-
oDoes duct slope away from the unit, DVCG statement:-
Unit Not Storing The Commissioning Settings
1. Has the power to the unit been switched off before the link has been moved from the Program to the Run
mode.
Unit Will Not Stay In Place Without The Additional Fixing Screws
1. Check the parts clip together correctly without the additional fixing screw. If they do not clip together
correctly it is possible the First Fix Base is twisted as it is not on a flat substrate. Undo the fixing screws and
re check the fitting.
Both Continuous and Boost Speeds Have Changed
The unit has re-set itself to factory setting, continuous is at %50 and boost is at 100%. This has probably
occurred after a power surge or a power outage. Try Re-commissioning.

PAGE 10 OF 10 FAULT FINDING FOR CME2Q+ LIVE ISSUE 2 03/04/20
894 The Crescent, Colchester Business Park, Colchester, Essex, CO4 9YQ United Kingdom Tel: [phone]
Fig 1 Fan Mains & Low Voltage Molex Connector
Mains Connections
Molex Connector
Fig 2 PCB Fuse
Fuse
Fig 3 Molex Connector
Potentiometer Connections
Fan Connector
A - 10V, B - 0V, C - PWM & D - Tacho
PCB Connector
If this is not possible, try bridging the A and C terminals on the fan connector, the fan should then run
at full speed.
Fig 4 Programming Link
Header Link in the Program position
Header Link in the Run poistion
Fig 5 Boost & Setback Inputs
Boost
Check there is 230V across N & LS1
Setback
Check there is 230V across N & LS2