TKH PD1103Z2-E User manual

USER
MANUAL
V2017.1.001
Network Speed Dome
PD1103Z2-E/T

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

2
Quick Start Guide
About this Manual
This Manual is applicable to WϭϭϬϯϮͲd Network Speed Dome.
The Manual includes instructions for using and managing the product. Pictures, charts,
images and all other information hereinafter are for description and explanation only.
The information contained in the Manual is subject to change, without notice, due to
firmware updates or other reasons. Please find the latest version in the company
website.
Please use this user manual under the guidance of professionals.
Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE
WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITES
FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING
FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET
SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL
SUPPORT IF REQUIRED.
SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN
YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR
USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE
EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES.
IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW,
THE LATER PREVAILS.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

3
Regulatory Information
FCC Information
FCC compliance: This equipment has been tested and found to comply with the limits
for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference when the
equipment is operated in a commercial environment. This equipment generates, uses,
and can radiate radio frequency energy and, if not installed and used in accordance with
the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference
in which case the user will be required to correct the interference at his own expense.
FCC Conditions
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may
cause undesired operation
EU Conformity Statement
This product and - if applicable - the supplied accessories too are marked
with "CE" and comply therefore with the applicable harmonized European
standards listed under the EMC Directive 2004/108/EC, the RoHS Directive
2011/65/EU.
2012/19/EU (WEEE directive): Products marked with this symbol cannot be
disposed of as unsorted municipal waste in the European Union. For proper
recycling, return this product to your local supplier upon the purchase of
equivalent new equipment, or dispose of it at designated collection points.
For more information see: www.recyclethis.info.
2006/66/EC (battery directive): This product contains a battery that cannot
be disposed of as unsorted municipal waste in the European Union. See the
product documentation for specific battery information. The battery is
marked with this symbol, which may include lettering to indicate cadmium
(Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to
your supplier or to a designated collection point. For more information see:
www.recyclethis.info.
Industry Canada ICES-003 Compliance
This device meets the CAN ICES-3 (A)/NMB-3(A) standards requirements.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

4
Safety Instruction
These instructions are intended to ensure that user can use the product correctly to
avoid danger or property loss.
The precaution measure is divided into Warnings and Cautions:
Warnings: Neglecting any of the warnings may cause serious injury or death.
Cautions: Neglecting any of the cautions may cause injury or equipment damage.
Warnings
zAll the electronic operation should be strictly compliance with the electrical safety
regulations, fire prevention regulations and other related regulations in your local
region.
zPlease use the power adapter, which is provided by normal company. The power
consumption cannot be less than the required value.
zDo not connect several devices to one power adapter as adapter overload may cause
over-heat or fire hazard.
zPlease make sure that the power has been disconnected before you wire, install or
dismantle the speed dome.
zWhen the product is installed on wall or ceiling, the device shall be firmly fixed.
zIf smoke, odors or noise rise from the device, turn off the power at once and unplug
the power cable, and then please contact the service center.
zIf the product does not work properly, please contact your dealer or the nearest
service center. Never attempt to disassemble the speed dome yourself. (We shall not
assume any responsibility for problems caused by unauthorized repair or
maintenance.)
zPlease do not look directly into the laser light within 6 meters because laser is
hazardous to humans.
Cautions
zDo not drop the dome or subject it to physical shock, and do not expose it to high
electromagnetism radiation. Avoid the equipment installation on vibrations surface or
places subject to shock (ignorance can cause equipment damage).
zDo not place the speed dome in extremely hot (refer to the specification of the
device for the detailed operating temperature), cold, dusty or damp locations, and do
not expose it to high electromagnetic radiation.
Warnings Follow
these safeguards to
prevent serious
injury or death.
Cautions Follow these
precautions to prevent
potential injury or
material damage.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

5
zThe dome cover for indoor use shall be kept from rain and moisture.
zExposing the equipment to direct sun light, low ventilation or heat source such as
heater or radiator is forbidden (ignorance can cause fire danger).
zDo not aim the speed dome at the sun or extra bright places. A blooming or smear
may occur otherwise (which is not a malfunction however), and affecting the
endurance of sensor at the same time.
zPlease use the provided glove when open up the dome cover, avoid direct contact
with the dome cover, because the acidic sweat of the fingers may erode the surface
coating of the dome cover.
zPlease use a soft and dry cloth when clean inside and outside surfaces of the dome
cover, do not use alkaline detergents.
zPlease keep all wrappers after unpack them for future use. In case of any failure
occurred, you need to return the speed dome to the factory with the original
wrapper. Transportation without the original wrapper may result in damage on the
speed dome and lead to additional costs.
zImproper use or replacement of the battery may result in hazard of explosion.
Replace with the same or equivalent type only. Dispose of used batteries according to
the instructions provided by the battery manufacturer.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

6
Table of Contents
1 Overview......................................................................................................1
1.1 Overview of Type I Speed Dome ............................................................................. 1
1.2 Overview of Type II Speed Dome ............................................................................ 2
1.3 Overview of Type III Speed Dome ........................................................................... 3
1.4 Overview of Type IV Speed Dome ........................................................................... 4
2 Installation ...................................................................................................5
2.1 Wall Mounting......................................................................................................... 5
2.1.1 Type I Speed Dome ........................................................................................... 6
2.1.2 Type II Speed Dome ........................................................................................ 10
2.1.3 Type III Speed Dome ....................................................................................... 13
2.1.4 Type IV Speed Dome ....................................................................................... 16
2.2 In-ceiling Mounting ............................................................................................... 20
2.3 Ceiling Mounting ................................................................................................... 22
2.3.1 Removing the In-ceiling Bracket...................................................................... 23
2.3.2 Wiring For Ceiling Mounting Applications....................................................... 23
2.3.3 Mounting ........................................................................................................ 24
3 Setting the Dome over the LAN .................................................................. 26
3.1 Wiring .................................................................................................................... 26
3.2 Activating the Speed Dome ................................................................................... 26
3.2.1 Activation via Web Browser............................................................................ 27
3.2.2 Activation via the Software............................................................................. 27
3.3 Modifying the IP Address ...................................................................................... 28
4 Accessing via Web Browser ........................................................................ 30

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

1
1Overview
Please turn the power off before connect the cables.
The overview of different speed domes can be categorized into four types, refer to the
content below for the details.
The cables are distinguished by different colors. The labels attached on the cables are for
identification.
Type I refers to the 5-inch speed dome.
Type II refers to the 6.5-inch speed dome.
Type III refers to the 7-inch IR speed dome and7-inch laser speed dome.
Type IV refers to the 8-inch IR speed dome and 8-inch laser speed dome.
The figures below are for reference only, please refer to the actual product as the
standard.
1.1 Overview of Type I Speed Dome
RED AC24V
YELLOW/GREEN
BLACK AC24V
1
2
3
4
5
6
7
8
Figure 1-1 Cable Interface of Type I Speed Dome

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

2
Table 1-1 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Audio Cable
3
Alarm Output Cables
4
Alarm Input Cables
5
RS-485 Cables
6
Video Cable
7
Power Cable
8
Micro SD Card Slot
1.2 Overview of Type II Speed Dome
2 types of the 6.5-inch speed dome structure are provided; please refer to
the actual product for the location of the SD card slot.
RED AC24V
YELLOW/GREEN
BLACKAC24V
<(//2:5
25$1*(5
9,(2'
1
2
3
4
5
6
7
Figure 1-2 Cable Interface of the Type II Speed Dome
8
Debug
Reset
8
Figure 1-3 SD Card Slot of the Type II Speed Dome

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

3
Table 1-2 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Audio Cable
3
Alarm Out
4
Alarm In
5
RS-485
6
Video Cable
7
Power Cable
8
SD Card Slot
1.3 Overview of Type III Speed Dome
1
2
3
4
5
6
7
SDCA RD
8
Figure 1-4 Cable Interface of the Type III Speed Dome
Table 1-3 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Audio Cable
3
Alarm Out
4
Alarm In
5
RS-485

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

4
No.
Description
6
Video Cable
7
Power Cable
8
SD Card Slot
1.4 Overview of Type IV Speed Dome
1
2
3
4
5
6
7
8
9
Figure 1-5 Cable Interface of the Type IV Speed Dome
Table 1-4 Descriptions of Cable Interface
No.
Description
1
Network Cable
2
Video Cable
3
Alarm Out
4
Audio Cable
5
Alarm In
6
RS-485
7
Power Cable
8
SD Card Slot
9
Head Cover

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

5
2Installation
Before you start:
භMake sure the device in the package is in good condition and all the assembly parts
are included.
භThe standard power supply is 12V DC or 24V AC, please make sure your power
supply matches with your speed dome.
භMake sure all the related equipment is power-off during the installation.
භCheck the specification of the products for the installation environment.
භMake sure that the wall is strong enough to withstand four times the weight of the
speed dome and the bracket.
For the speed dome that supports IR, you are required to pay attention to the following
precautions to prevent IR reflection:
භDust or grease on the dome cover will cause IR reflection. Please do not remove the
dome cover film until the installation is finished. If there is dust or grease on the
dome cover, clean the dome cover with clean soft cloth and isopropyl alcohol.
භMake sure that there is no reflective surface too close to the lens. The IR light from
the speed dome may reflect back into the lens causing reflection.
Do not drag the speed dome with its waterproof cables as shown in Figure 2-1,
otherwise the waterproof performance is affected.
Figure 2-1 Do Not Drag the Cables
2.1 Wall Mounting
Before you start:
Please turn off the power of the speed dome before connecting the cables.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

6
zFor cement wall, you need to use the expansion screw to fix the bracket. The
mounting hole of the expansion pipe on the wall should align with the mounting
hole on the bracket.
zFor wooden wall, you can just use the self-tapping screw to fix the bracket.
zPlease make sure that the wall is strong enough to withstand more than 8 times the
weight of the dome and the bracket.
zThe bracket in Figure 2-7 is the recommended bracket for this series of speed
dome, and a pendent adapter is required if any other bracket is selected.
2.1.1 Type I Speed Dome
The long-arm bracket is taken as the example for following mounting steps.
Steps:
1. Loosen the two lock screws on the both side of the speed dome. Pull the lower dome
to separate it from the back box as shown in Figure 2-2.
2. Remove Protective elements.
For Separate 5-inch speed dome: Pull the camera module to separate it from the
back box, as shown in Figure 2-3.
For Integrated 5-inch speed dome: Remove the protective foam, sticker and lens
cover from the dome drive. As shown in Figure 2-4.
Please do not remove the lock screws from the dome.
Back Box
Lower Dome
Protective Foam
Lens Cover
Figure 2-2 Remove the Lower Dome

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

7
Figure 2-3 Remove the sticker for separated 5-inch speed dome
Figure 2-4 Remove the Sticker for Integrated 5-inch speed dome
3. If the speed dome supports the PoE (Power Over Ethernet) function, you can switch
the PoE+ and Hi-PoE function of the dome camera. If the speed dome only supports
the power cable, you can skip this step.
12
ON
Figure 2-5 PoE+ and Hi-PoE Switch

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

8
If you choose Hi-PoE, a Hi-PoE adapter must be connected.
Power supply via Hi-PoE is supported. The Hi-PoE module connection is shown below.
12
3 4
Network Speed
Dome
Ethernet
1: Power Indicator
2: PORT Indicator
3:DATA&POWER OUT
4: DATA IN
Figure 2-6 Hi-PoE Connection
Connecting Hi-PoE
Steps:
1) Connect the Hi-PoE module to the internet via the DATA IN interface with a
network cable.
2) Connect the Hi-PoE module to the speed dome via the DATA & POWER OUT
interface with a network cable.
3) Power on the Hi-PoE module.
Please power the Hi-PoE module according to its power supply parameters.
4. Align the cuts on the lower dome with the lock screws on the back box to reinstall the
lower dome. Tighten the lock screws.
5. Drill 4 screw holes in the wall according to the holes of the bracket, and then insert
M8 expansion screws into the mounting holes.
6. Attach the gasket then bracket to the wall by aligning the 4 screw holes of the bracket
with expansion screws on the wall.
7. Secure the bracket with 4 hex nuts and washers.
Figure 2-7 Secure the Bracket
8. Install the speed dome to the bracket.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

9
1). Hang the safety rope to the speed dome and the hook on the bracket as shown in
Figure 2-8.
2). Route the cables of the speed dome through the bracket.
3). Connect the corresponding cables.
Safety Rope
Figure 2-8 Hang the Safety Rope
4). Loosen the two lock screws on the bracket.
5). Install the speed dome to the bracket. Rotate the speed dome clockwise tightly.
6). Secure the two lock screws with the Allen wrench.
Lock Screw
Figure 2-9 Mount the Dome
zThe bracket in Figure 2-7 is the recommended bracket for this series of speed dome,
and a pendent adapter is required if any other bracket is selected. See Figure 2-10.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

10
Pendant Adapter
Lock Screw
Figure 2-10 Pendent Adapter
2.1.2 Type II Speed Dome
The long-arm bracket is taken as the example for the following mounting steps.
Steps:
1. Loosen the 4 lock screws on the flange of the speed dome; refer to the Figure 2-11.
Lock Screws
Figure 2-11 Loosen the Lock Screws
Please do not remove the lock screws from the dome.
2. Pull the lower dome to separate it from the back box, and remove the protective
foam, sticker and lens cover from the dome drive.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

11
Back Box
Lens Cover
Protective Foam
Lower Dome Sticker
Figure 2-12 Remove the Protective Elements
3. Install the micro SD card of the speed dome.
SD Card Slot
Debug
Reset
Open Cover
SD Card Slot
Figure 2-13 Install the SD Card.
4. Align the cuts on the lower dome with the lock screws on the back box to reinstall the
lower dome. Tighten the lock screws.
5. Refer to the steps 5-7 of the section 2.1.1 to install the bracket.
6. Install the speed dome to the bracket.
1). Hook the back box of the speed dome to the bracket with the safety rope. Route
the cables through the bracket.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

12
2). Connect the corresponding cables.
Figure 2-14 Hang the Safety Rope
3). Loosen the two lock screws on the bracket.
4). Install the speed dome to the bracket. Rotate the speed dome clockwise tightly.
5). Secure the two lock screws with the Allen wrench.
Lock Screw
Figure 2-15 Mount the Dome
zThe bracket in Figure 2-7 is the recommended bracket for this series of speed dome,
and a pendent adapter is required if any other bracket is selected.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

13
Pendant Adapter
Lock Screw
Figure 2-16 Pendent Adapter
2.1.3 Type III Speed Dome
Steps:
1. Remove the protective sticker as shown in Figure 2-17.
Protective Sticker
Figure 2-17 Remove Protective Sticker
2. Remove the cover on the back of the speed dome as shown in Figure 2-18. Insert the
SD card to the SD card slot and install the cover back.

User Manual - Network Speed Dome - WϭϭϬϯϮͲd

14
SD CARD
SD Card Slot
Figure 2-18 SD Card Slot
3. Refer to the steps 5-7 of the section 2.1.1 to install the bracket.
4. Hook the two ends of the safety rope to the back box of the speed dome and the
bracket respectively. Route the cables through the bracket as shown follows.
Safety Rope
Figure 2-19 Install the Safety Rope
5. Loosen the lock screws on the bracket.
6. Align the speed dome with bracket and rotate it counterclockwise or clockwise to the
bracket tightly as shown below.