Toro 07383 User manual

Form No. 3463-627 Rev A
W orkman
®
HDX Utility V ehicle
Model No. 07383 —Serial No. 412849600 and Up
Model No. 07384 —Serial No. 414810000 and Up
Model No. 07386 —Serial No. 414993557 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3463-627*

It is a violation of California Public Resource Code
Section 4442 or 4443 to use or operate the engine on
any forest-covered, brush-covered, or grass-covered
land unless the engine is equipped with a spark
arrester , as dened in Section 4442, maintained in
ef fective working order or the engine is constructed,
equipped, and maintained for the prevention of re.
The enclosed engine owner's manual is supplied
for information regarding the US Environmental
Protection Agency (EP A) and the California Emission
Control Regulation of emission systems, maintenance,
and warranty . Replacements may be ordered through
the engine manufacturer .
W ARNING
CALIFORNIA
Proposition 65 W arning
The engine exhaust from this product
contains chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm. W ash
hands after handling.
Introduction
This utility vehicle is intended to be primarily used
of f-highway to transport people and material loads.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for product safety and operation
training materials, accessory information, help nding
a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Distributor or T oro Customer Service and have the
model and serial numbers of your product ready .
Figure 1 identies the location of the model and serial
numbers on the product. W rite the numbers in the
space provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information.
g239323
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The safety-alert symbol ( Figure 2 ) appears both in
this manual and on the machine to identify important
safety messages that you must follow to avoid
accidents. This symbol will appear with the word
Danger ,W arning , or Caution .
•Danger indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury .
•W arning indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury .
•Caution indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury .
g000502
Figure 2
Safety-alert symbol
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in the USA
All Rights Reserved

Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
1 Installing the Roll Bar . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
2 Checking the Fluid Levels and T ire
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
3 Burnishing the Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Performing Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Adding Fuel . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Breaking in a New Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Checking the Safety-Interlock System . . . . . . . . . . . . . . 22
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Operating the Cargo Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Starting the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Engaging the 4-Wheel Drive . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Driving the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Stopping the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Shutting Of f the Engine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Using the Dif ferential Lock . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
Using the Hydraulic Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Hauling the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
T owing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
T owing a T railer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recommended Maintenance Schedule(s) . . . . . . . . . . . 31
Maintaining the Machine under Special
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Pre-Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Preparing the Machine for Maintenance . . . . . . . . . . . . 33
Using the Bed Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Removing the Full Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing the Full Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Raising the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Removing and Installing the Hood . . . . . . . . . . . . . . . . . . . . 36
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Greasing the Bearings and Bushings . . . . . . . . . . . . . . . . 37
Engine Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Engine Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Servicing the Air Cleaner . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Servicing the Engine Oil . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Replacing the Spark Plugs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Fuel System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Replacing the Fuel Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Inspecting Fuel Lines and Connections . . . . . . . . . . . . . 43
Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Electrical System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Servicing the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Jump-Starting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Servicing the Battery . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Checking the Front Dif ferential-Oil
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Changing the Front Dif ferential Oil . . . . . . . . . . . . . . . . . . . . 46
Inspecting the Constant-V elocity Boot . . . . . . . . . . . . . . 47
Adjusting the Shift Cables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting the High-Low Cable . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting Dif ferential-Lock Cable . . . . . . . . . . . . . . . . . . . . . . 47
Inspecting the T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Checking the Front Wheel Alignment . . . . . . . . . . . . . . . . 48
T orquing the Wheel Lug Nuts . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Cooling System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Cooling System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 50
Checking the Engine-Coolant Level . . . . . . . . . . . . . . . . . . 50
Removing Debris from the Cooling
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Changing the Engine Coolant . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Brake Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Checking the Brake-Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . 52
Adjusting the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 52
Adjusting the Brake Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 53
Belt Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Adjusting the Alternator Belt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54
Controls System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Adjusting the Clutch Pedal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55
Adjusting the Accelerator Pedal . . . . . . . . . . . . . . . . . . . . . . . . 56
Hydraulic System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Hydraulic System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Servicing the T ransaxle/Hydraulic
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 56
Servicing the High-Flow Hydraulic
System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Raising the Cargo Bed in an Emergency . . . . . . . . . . . 60
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
W ashing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Storing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
T roubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
3

Safety
This machine has been designed in accordance with
the requirements of SAE J2258 (Nov 2016).
General Safety
This product is capable of causing personal injury .
Always follow all safety instructions to avoid serious
personal injury .
•Read and understand the contents of this
Operator ’ s Manual before you start the machine.
Ensure that everyone using this product knows
how to use it and understands the warnings.
•Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
•Do not put your hands or feet near moving
components of the machine.
•Do not operate the machine without all guards
and other safety protective devices in place and
working on the machine.
•Keep bystanders and children out of the operating
area. Never allow children to operate the machine.
•Stop and shut of f the machine and remove the key
before servicing or fueling.
Improperly using or maintaining this machine can
result in injury . T o reduce the potential for injury ,
comply with these safety instructions and always
pay attention to the safety-alert symbol , which
means Caution, W arning, or Danger—personal safety
instruction. Failure to comply with these instructions
may result in personal injury or death.
4

Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decalbatterysymbols
Battery Symbols
Some or all of these symbols are on your battery .
1. Explosion hazard 6. Keep bystanders away
from the battery .
2. No re, open ame, or
smoking
7. W ear eye protection;
explosive gases can
cause blindness and other
injuries.
3. Caustic liquid/chemical
burn hazard
8. Battery acid can cause
blindness or severe burns.
4. W ear eye protection. 9. Flush eyes immediately
with water and get medical
help fast.
5. Read the Operator's
Manual .
10. Contains lead; do not
discard
decal93-9850
93-9850
1. Do not repair or revise—read the Operator's Manual.
decal93-9852
93-9852
1. W arning—read the Operator ’ s Manual. 2. Crushing hazard—install the cylinder lock.
decal93-9868
93–9868
1. Crushing hazard of hand—read the Operator ’ s Manual .
decal93-9879
93-9879
1. Stored energy hazard—read the Operator's Manual.
93-9899
decal93-9899
93-9899
1. Crushing hazard—install the cylinder lock.
5

decal105-4215
105-4215
1. W arning—avoid pinch points.
decal106-2355
106-2355
1. Slow
3. T ransmission—third high;
no fast speed
2. Fast
decal106-2377
106-2377
1. Locked
8. W arning—read the Operator's Manual.
2. Dif ferential lock 9. Entanglement hazard, shaft—keep bystanders out of the
operating area.
3. Unlocked 10. Retract hydraulics
4. Hydraulic lock 1 1. Extend hydraulics
5. Engage 12. T ransmission—high speed
6. Power takeof f (PT O)
13. T ransmission—low speed
7. Disengage 14. Parking brake
6

decal106-6755
106-6755
1. Engine coolant under
pressure.
3. W arning—do not touch the
hot surface.
2. Explosion hazard—read
the Operator's Manual.
4. W arning—read the
Operator's Manual.
decal106-7767
106-7767
1. W arning—read the Operator's Manual ; avoid tipping the
machine; wear the seat belt; lean away from the direction
the machine is tipping.
decal1 10-0806
1 10-0806
1. Caution—do not use starting uid
decal1 15-2047
1 15-2047
1. W arning—do not touch the hot surface.
7

decal1 15-2282
1 15-2282
1. W arning—read the Operator's Manual .
2. W arning—stay away from moving parts; keep all guards and shields in place.
3. Crushing hazard—keep bystanders out of the operating area; do not carry passengers in the cargo bed; keep arms and legs
inside of the vehicle at all times; use seat belts and handholds.
decal1 15-7723
1 15-7723
1. W arning—the hydraulic-uid pressure is 124 bar (1,800 psi).
2. Coupler A
3. Coupler B
decal1 15-7739
1 15-7739
1. Falling, crushing hazard—do not carry passengers.
decal1 15-7741
1 15-7741
1. Read the Operator ’ s Manual before servicing transmission
uid.
decal121-6286
121-6286
1. Check the coolant level
daily before use of
the machine. Read
the Operator's Manual
before checking the
engine-coolant level.
2. Do not open or add coolant
to the radiator; doing so
introduces air into the
system and results in
engine damage. Add
only engine coolant to the
reservoir .
decal121-6287
121-6287
1. Fill the reservoir with engine coolant to the bottom of the
ller neck.
8

decal121-9776
121-9776
1. W arning—read the Operator ’ s Manual and receive proper
training before operating the machine.
4. W arning—engage the parking brake, shut of f the engine, and
remove the key from the key switch before walking away from
the machine.
2. W arning—wear hearing protection. 5. T ipping hazard—take turns slowly; drive slowly up and across
clif fs; with no load, do not exceed 32 kph (20 mph); while
carrying a load or when driving on uneven terrain, drive slowly .
3. Fire hazard—shut of f the engine before refueling the machine.
decal136-1 163
136-1 163
1. Do not exceed a transport
load of 1591 kg (3,500 lb).
2. Do not exceed a tongue
weight of 273 kg (600 lb).
decal137-9896
137-9896
1. 4x4 engage button
decal139-3341
139-3341
1. T ank 3. Pressure
2. W arning—the
hydraulic-uid pressure is
138 bar (2,000 psi).
9

decal145-2276
145-2276
1. Engine—stop 3. Engine—start
2. Engine—run
decal145-2282
145-2282
1. Power point
decal145-2286
145-2286
1. Power outlet (10 A) 5. Lights, brake (15 A)
2. Switched power (10 A) 6. Hazard (10 A)
3. Fuel pump, supervisor
switch (10 A)
7. 4WD, transmission (10 A)
4. Horn, power point (15 A)
10

Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
Roll bar 11
Flange-head bolt (1/2 x 1-1/4 inches)
6
Install the roll bar .
2
No parts required
–
Check the uid levels and tire pressure.
3
No parts required
–
Burnish the brakes.
Note: Determine the left and right sides of the machine from the normal operating position.
1
Installing the Roll Bar
Parts needed for this procedure:
1 Roll bar
6
Flange-head bolt (1/2 x 1-1/4 inches)
Procedure
1. Apply medium-grade (service-removable)
thread-locking compound to the threads of the 6
ange-head bolts (1/2 x 1-1/4 inches).
2. Align each side of the roll bar with the mounting
holes on each side of the machine frame ( Figure
3).
g009812
Figure 3
1. Roll bar mounting bracket
2. Flange-head bolt (1/2 x
1-1/4 inches)
3. Secure the roll bar mounting bracket to the
machine frame using 3 ange-head bolts (1/2 x
1-1/4 inches) on each side ( Figure 3 ).
4. T orque the ange-head bolts (1/2 x 1-1/4 inches)
to 1 15 N∙m (85 ft-lb).
1 1

2
Checking the Fluid Levels
and T ire Pressure
No Parts Required
Procedure
1. Check the engine-oil level before and after
you rst start the engine; refer to Checking the
Engine-Oil Level ( page 40 ) .
2. Check the transaxle/hydraulic-uid level before
you rst start the engine; refer to Checking the
T ransaxle/Hydraulic-Fluid Level ( page 56 ) .
3. Check the brake-uid level before you rst start
the engine; refer to Checking the Brake-Fluid
Level ( page 52 ) .
4. Check the coolant level; refer to Checking the
Engine-Coolant Level ( page 50 ) .
5. Check the air pressure in the tires; refer to
Checking the T ire Pressure ( page 20 ) .
3
Burnishing the Brakes
No Parts Required
Procedure
T o ensure optimum performance of the brake system,
burnish the brakes before use.
1. Bring the machine up to full speed, apply the
brakes to rapidly stop the machine without
locking up the tires.
2. Repeat this procedure 10 times, waiting 1 minute
between stops, to avoid overheating the brakes.
Important: This procedure is most effective
if the machine is loaded with 454 kg (1,000
lb).
12

Product Overview
Controls
Become familiar with all the controls before you start the engine and operate the machine.
Control Panel
g381 123
Figure 4
1. Horn switch 5. Display
2. Light switch 6. Power point
3. 4-wheel drive switch (4-wheel drive models only)
7. Key switch
4. High-ow hydraulics switch (TC models only) 8. Supervisor switch
13

Display
g347586
Figure 5
1. Fuel gauge
6. Check-engine indicator
2. T achometer/engine speed (rpm)
7. T achometer-speedometer location change
button/Speedometer conversion button
3. Speedometer (km/h or mph)
8. Hour meter
4. Coolant-temperature gauge and light 9. Oil-pressure-warning light
5. Glow-plug indicator (diesel machines only) 10. Charge indicator
14

Accelerator Pedal
Use the accelerator pedal ( Figure 6 ) to vary the ground
speed of the machine when the transmission is in
gear . Pressing down the accelerator pedal increases
the engine speed and ground speed. Releasing the
pedal decreases the engine speed and ground speed.
g021226
Figure 6
1. Clutch pedal
3. Accelerator pedal
2. Brake pedal
Clutch Pedal
Y ou must fully press the clutch pedal ( Figure 6 )
to disengage the clutch when starting the engine
or shifting transmission gears. Release the pedal
smoothly when the transmission is in gear to prevent
unnecessary wear on the transmission and other
related parts.
Important: Do not ride the clutch pedal during
operation. The clutch pedal must be fully out or
the clutch slips, causing heat and wear . Never
hold the machine stopped on a hill using the
clutch pedal. Damage to the clutch may occur .
Brake Pedal
Use the brake pedal to stop or slow the machine
(Figure 6 ).
CAUTION
Operating a machine with worn or incorrectly
adjusted brakes can may result in personal
injury .
If the brake pedal travels to within 25 mm (1
inch) of the machine oor board, adjust or
repair the brakes.
Gear-Shift Lever
Fully press the clutch pedal and move the shift lever
(Figure 7 ) into the desired gear selection. A diagram
of the shift pattern is shown below .
g009160
Figure 7
Important: Do not shift the transaxle to the
REVERSE or F ORWARD gear unless the machine is
motionless; otherwise, you could damage the
transaxle.
CAUTION
Down-shifting from too high a speed can
cause the rear wheels to skid, resulting in loss
of machine control as well as clutch and/or
transmission damage.
Shift smoothly to avoid grinding the gears.
Differential Lock
The dif ferential lock ( Figure 8 ) allows the rear axle
to lock for increased traction. Y ou can engage the
dif ferential lock when the machine is in motion.
Move the lever forward and to the right to engage
the lock.
Note: Machine motion plus a slight turn is required to
engage or disengage the dif ferential lock.
CAUTION
T urning with the differential lock on can result
in the loss of machine control.
Do not operate the machine with the
differential lock on when making sharp
turns or at high speeds; refer to Adjusting
Differential-Lock Cable ( page 47 ) .
15

g350294
Figure 8
1. Parking-brake lever
5. High-low range shifter
2. Hydraulic-bed lift
6. 4-wheel drive button
(4-wheel drive models
only)
3. Hydraulic-lift lock 7. Gear-shift lever
4. Dif ferential lock
Parking-Brake Lever
Whenever you shut of f the engine, engage the
parking brake ( Figure 8 ) to prevent the machine from
accidentally moving.
•T o engage the parking brake, pull back on the
parking-brake lever .
•T o disengage the parking brake, push the
parking-brake lever forward.
Note: Disengage the parking brake before
moving the machine.
If you park the machine on a steep grade, engage the
parking brake, shift the transmission into F IRST gear
on a uphill grade or R EVERSE gear on a downhill grade,
and place chocks at the downhill side of the wheels.
Hydraulic-Lift Lever
The hydraulic lift raises and lowers the bed. Move
it rearward to raise the bed, and forward to lower it
(Figure 8 ).
Important: When lowering the bed, hold the lever
in the forward position for 1 to 2 seconds after the
bed contacts the frame to secure it in the lowered
position. Do not hold the hydraulic lift in the raise
or lower position for more than 5 seconds, once
the cylinders reach the end of their travel.
Hydraulic-Lift Lock
The hydraulic-lift lock secures the lift lever , so that the
hydraulic cylinders do not operate when the machine
is not equipped with a bed ( Figure 8 ). It also locks the
lift lever in the O Nposition when using the hydraulics
for attachments.
High-Low Range Shifter
The high-low range shifter adds 3 additional speeds
for precise speed control ( Figure 8 ):
•Y ou must stop the machine completely before
shifting between the H IGH and L OW range.
•Shift on level ground only .
•Press the clutch pedal fully .
•Move the lever fully forward for H IGH and fully
rearward for L OW .
HIGH range —For higher speed driving on level, dry
surfaces with light loads.
LOW range —For low-speed driving. Use this
range when greater than normal power or control
is necessary . For example, steep grades, dif cult
terrain, heavy loads, slow speed but high-engine
speed (spraying).
Important: There is a location between H IGH and
LOW in which the transaxle is in neither range.
Do not use this position as a N EUTRAL position,
because the machine could move unexpectedly if
the High-Low shifter is bumped and the gear-shift
lever is in gear .
4-Wheel Drive Button
4-Wheel Drive Models Only
T o engage the 4-wheel drive manually , press and
hold the 4WD button ( Figure 8 ) on the center console
while the vehicle is in motion and the 4-wheel drive
engages.
Key Switch
Use the key switch ( Figure 4 ) to start and shut of f
the engine.
The key switch has 3 positions: O FF , O N, and S TART .
Rotate the key switch clockwise to the S TART position
to engage the starter motor . Release the key switch
when the engine starts. The key switch moves
automatically to the O Nposition.
T o shut the engine of f, rotate the key switch
counterclockwise to the O FF position.
16

Supervisor Switch
Move the supervisor switch ( Figure 4 ) to the SLOW
position and remove the key . The supervisor switch
limits the engine speed to 2,200 rpm when the
machine is in third gear in the HIGH range, which
limits the top speed to 21 km/h (13 mph).
Hour Meter
The hour meter ( Figure 5 ) indicates the total hours of
machine operation.
The hour meter starts to function whenever you rotate
the key switch to the O Nposition and the engine
speed (rpm) is over 500 rpm every 6 minutes.
Light Switch
Push the light switch ( Figure 5 ) to toggle the headlights
on or of f.
Oil-Pressure-W arning Light
The oil-pressure-warning light ( Figure 5 ) illuminates if
the engine-oil pressure drops below a safe level while
the engine is running.
Important: If the light ickers or remains on,
stop the machine, shut off the engine, and check
the oil level. If the oil level is low , but adding
oil does not cause the light to go out when the
engine is started, shut off the engine immediately ,
and contact your Authorized Service Dealer for
assistance.
Check the operation of the warning lights as follows:
1. Engage the parking brake.
2. T urn the key switch to the O N/P REHEAT position,
but do not start the engine.
Note: The oil-pressure light should glow red.
If the light does not function, either a bulb is
burned out or there is a malfunction in the
system that you must repair .
Note: If engine was just shut of f, it may take 1
to 2 minutes for the light to come on.
Coolant-T emperature Gauge and
Light
The coolant-temperature gauge and light registers the
coolant temperature in the engine and operates only
when the key switch is in O Nposition ( Figure 5 ).
The 5 coolant bars blink if the engine overheats.
Charge Indicator
The charge indicator illuminates when the battery
discharges. If the light illuminates during operation,
stop the machine, shut of f the engine, and check for
possible causes, such as the alternator belt ( Figure 5 ).
Important: If the alternator belt is loose or
broken, do not operate the machine until the
adjustment or repair is complete. Failure to
observe this precaution may damage the engine.
Check the operation of the warning lights as follows:
•Engage the parking brake.
•T urn the key switch to the O N/P REHEAT position,
but do not start the engine. The coolant
temperature, charge indicator , and oil-pressure
lights should glow . If any light does not function,
either a bulb is burned out or there is a malfunction
in the system that you must repair .
Fuel Gauge
The fuel gauge shows the amount of fuel in the tank.
It displays only when key switch is in the O Nposition
(Figure 5 ).
A single bar indicates a low fuel level and 1 ashing
bar indicates that the fuel tank is nearly empty .
4-Wheel Drive Switch
4-Wheel Drive Models Only
When the 4WD switch ( Figure 4 ) is on, the machine
automatically engages the 4-wheel drive if the sensor
detects the back wheels spinning freely . When the
4-wheel drive is engaged, the 4WD switch light turns
on.
4WD works only in the forward direction in A UTO
mode. If you want it in R EVERSE , press the 4WD
button.
High-Flow Hydraulics Switch
TC Models Only
T urn on the switch to activate the high-ow hydraulics
(Figure 4 ).
Horn Switch
The horn switch is located on the control panel ( Figure
4). Press the horn switch to sound the horn.
17

T achometer
The tachometer displays the speed of the engine
(Figure 5 ).
Note: 3,300 rpm is the desired engine speed for 540
rpm PT O operation.
Check-Engine Light
The check-engine light illuminates to indicate
an engine malfunction; refer to Responding to a
Check-Engine Light ( page 41 ) .
Speedometer
The speedometer registers the ground speed of the
machine ( Figure 5 ).
T achometer-Speedometer
Location Change
Button/Speedometer Conversion
Button
Press, hold, and release the button ( Figure 5 ) between
0 to 3 seconds to swap the locations of tachometer
and speedometer .
Press, hold, and release the button ( Figure 5 ) between
3 to 10 seconds to convert the speedometer from
mph to km/h.
Power Point
Use the power point ( Figure 4 ) to power optional 12
V electrical accessories.
Passenger Handhold
The passenger handhold is located on the dashboard
(Figure 9 ).
g009815
Figure 9
1. Passenger handhold
2. Storage compartment
Seat-Adjustment Lever
Y ou can adjust the seat forward and rearward for your
comfort ( Figure 10 ).
g021227
Figure 10
1. Seat-adjustment lever
18

Specications
Note: Specications and design are subject to
change without notice.
Overall width 160 cm (63 inches)
Without bed: 326 cm (128 inches)
With full bed: 331 cm (130 inches)Overall length
With 2/3 bed in rear-mounting location: 346 cm (136 inches)
Model 07383: 736 kg (1,623 lb)
Model 07384: 885 kg (1,951 lb)Base weight (dry)
Model 07386: 912 kg (2,010 lb)
Model 07383: 1623 kg (3,577 lb)
Model 07384: 1474 kg (3,249 lb)Rated capacity (includes 91 kg (200 lb) operator ,
91 kg (200 lb) passenger , and loaded attachment)
Model 07386: 1447 kg (3,190 lb)
Maximum gross vehicle weight (GVW) 2359 kg (5,200 lb)
T ongue weight: 272 kg (600 lb)T ow capacity
Maximum trailer weight: 1587 kg (3,500 lb)
Ground clearance 18 cm (7 inches) with no load
Wheel base
1 18 cm (70 inches)
Front: 1 17 cm (46 inches)Wheel tread (center line to center line)
Rear: 121 cm (48 inches)
Height
191 cm (75 inches) to top of ROPS
Attachments/Accessories
A selection of T oro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or Distributor or go to www .T oro.com for a
list of all approved attachments and accessories.
T o ensure optimum performance and continued safety certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be
dangerous, and such use could void the product warranty .
19

Operation
Note: Determine the left and right sides of the
machine from the normal operating position.
Before Operation
Before Operation Safety
General Safety
•Never allow children or people who are not trained
or physically capable to safely operate or service
the machine. Local regulations may restrict the
age of the operator . The owner is responsible for
training all operators and mechanics.
•Become familiar with the safe operation of the
equipment, operator controls, and safety signs.
•Shut of f the machine, remove the key , and wait
for all movement to stop before you leave the
operator ’ s position. Allow the machine to cool
before adjusting, servicing, cleaning, or storing it.
•Know how to stop and shut of f the machine quickly .
•Ensure that there are not more occupants (you and
your passenger(s)) than the number of handholds
equipped on the machine.
•Check that all safety devices and decals are in
place. Repair or replace all safety devices and
replace all illegible or missing decals. Do not
operate the machine unless they are present and
functioning properly .
Fuel Safety
•Use extreme care in handling fuel. It is ammable
and its vapors are explosive.
•Extinguish all cigarettes, cigars, pipes, and other
sources of ignition.
•Use only an approved fuel container .
•Do not remove the fuel cap or ll the fuel tank
while the engine is running or hot.
•Do not add or drain fuel in an enclosed space.
•Do not store the machine or fuel container where
there is an open ame, spark, or pilot light, such
as on a water heater or other appliance.
•If you spill fuel, do not attempt to start the engine;
avoid creating any source of ignition until the fuel
vapors have dissipated.
Performing Daily
Maintenance
Service Interval : Before each use or daily
Before starting the machine each day , perform the
Each Use/Daily procedures listed in Maintenance
( page 30 ) .
Checking the T ire Pressure
Service Interval : Before each use or daily
Front tires air pressure specication: 220 kPa (32
psi)
Rear tires air pressure specication: 124 kPa (18
psi)
Important: Check the tire pressure frequently
to ensure proper ination. If the tires are not
inated to the correct pressure, the tires will wear
prematurely and may cause the 4-wheel drive to
bind.
Figure 1 1 shows an example of tire wear caused by
under-ination.
g010294
Figure 1 1
1. Under-inated tire
Figure 12 shows an example of tire wear caused by
over-ination.
g010293
Figure 12
1. Over-inated tire
20