Toro 07433LT User manual

Form No. 3461-251 Rev A
W orkman
®
GTX Lithium Utility
V ehicle
Model No. 07433L T —Serial No. 400000000 and Up
Model No. 07433TC —Serial No. 400000000 and Up
Register at www .T oro.com.
Original Instructions (EN)
*3461-251*

This product complies with all relevant European
directives; for details, please see the separate product
specic Declaration of Conformity (DOC) sheet.
W ARNING
CALIFORNIA
Proposition 65 W arning
The power cord on this product contains
lead, a chemical known to the State
of California to cause birth defects
or other reproductive harm. W ash
hands after handling.
Battery posts, terminals, and related
accessories contain lead and lead
compounds, chemicals known to
the State of California to cause
cancer and reproductive harm. W ash
hands after handling.
Use of this product may cause exposure
to chemicals known to the State of
California to cause cancer , birth defects,
or other reproductive harm.
Introduction
This utility vehicle is intended to be primarily used
of f-highway to transport people and material loads.
Using this product for purposes other than its intended
use could prove dangerous to you and bystanders.
Read this information carefully to learn how to operate
and maintain your product properly and to avoid
injury and product damage. Y ou are responsible for
operating the product properly and safely .
V isit www .T oro.com for product safety and operation
training materials, accessory information, help nding
a dealer , or to register your product.
Whenever you need service, genuine T oro parts, or
additional information, contact an Authorized Service
Distributor or T oro Customer Service and have the
model and serial numbers of your product ready .
Figure 1 identies the location of the model and serial
numbers on the product. W rite the numbers in the
space provided.
Important: W ith your mobile device, you can
scan the QR code on the serial number decal (if
equipped) to access warranty , parts, and other
product information.
g282597
Figure 1
1. Model and serial number location
Model No.
Serial No.
This manual uses 2 words to highlight information.
Important calls attention to special mechanical
information and Note emphasizes general information
worthy of special attention.
The safety-alert symbol ( Figure 2 ) appears both in
this manual and on the machine to identify important
safety messages that you must follow to avoid
accidents. This symbol will appear with the word
Danger ,W arning , or Caution .
•Danger indicates an imminently hazardous
situation which, if not avoided, will result in death
or serious injury .
•W arning indicates a potentially hazardous
situation which, if not avoided, could result in
death or serious injury .
•Caution indicates a potentially hazardous situation
which, if not avoided, may result in minor or
moderate injury .
g000502
Figure 2
Safety-alert symbol
© 2023—The T oro® Company
81 1 1 L yndale A venue South
Bloomington, MN 55420
2
Contact us at www .T oro.com.
Printed in the USA
All Rights Reserved

Contents
Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
General Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Safety and Instructional Decals . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
1 Installing the Steering Wheel . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2 Charging the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
3 Checking the Fluid Levels and T ire
Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
4 Burnishing the Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
5 Reading the Manual and V iewing the
Setup Material . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Product Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1 1
Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Display . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Specications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Attachments/Accessories . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Before Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Before Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Performing Daily Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Checking the T ire Pressure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Breaking in a New Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
During Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
During Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Operating the Cargo Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Monitoring the Battery-System Charge
Level . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Stopping the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Loading the Cargo Bed . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
After Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
After Operation Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Hauling the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
T owing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
T owing a T railer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
T ransporting the Lithium-Ion Batteries . . . . . . . . . . . . . . 28
Understanding the Lithium-Ion Battery
Charger . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Maintenance Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Recommended Maintenance Schedule(s) . . . . . . . . . . . 31
Daily Maintenance Checklist . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Maintaining the Machine under Special
Operating Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Pre-Maintenance Procedures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Preparing the Machine for Maintenance . . . . . . . . . . . . 33
Lifting the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Accessing the Hood . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 33
Raising and Lowering the Seat
Assembly . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Removing a Bucket Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Installing a Bucket Seat . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Removing a Bench Cushion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Installing a Bench Cushion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Lubrication . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Greasing the Front Wheel Bearings . . . . . . . . . . . . . . . . . . 36
Electrical System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Electrical System Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Using the Battery-Disconnect Switch . . . . . . . . . . . . . . . . 39
Servicing the Batteries . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39
Maintaining the Lithium-Ion Batteries . . . . . . . . . . . . . . . . 39
Maintaining the Battery Charger . . . . . . . . . . . . . . . . . . . . . . . 39
Locating the Fuses . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Maintaining the Headlights . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40
Drive System Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Maintaining the T ires . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Inspecting the Steering and Suspension
Components . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Adjusting the Wheel Alignment . . . . . . . . . . . . . . . . . . . . . . . . . 42
Checking the T ransaxle-Fluid Level . . . . . . . . . . . . . . . . . . 44
Changing the T ransaxle Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Brake Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Checking the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Adjusting the Parking Brake . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
Checking the Brake-Fluid Level . . . . . . . . . . . . . . . . . . . . . . . . 45
Inspecting the Brakes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Replacing the Service and Parking-Brake
Pads .............................................................. 46
Changing the Brake Fluid . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Chassis Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Adjusting the Cargo-Bed Latches . . . . . . . . . . . . . . . . . . . . . 47
Cleaning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
W ashing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Storage Safety . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Storing the Machine . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Battery Storage Requirements . . . . . . . . . . . . . . . . . . . . . . . . . 48
3

Safety
General Safety
•This product is capable of causing personal injury
or death. Always follow all safety instructions to
avoid serious personal injury .
•Improper operation, maintenance, or poor
housekeeping of the machine may cause it to
become unstable; other factors include terrain
conditions, slope, speed, and poor operator
judgment.
•Read and understand the contents of this
Operator ’ s Manual before you start the machine.
Ensure that everyone using this product knows
how to use it and understands the warnings.
•Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
•Do not put your hands or feet near moving
components of the machine.
•Do not operate the machine without all guards
and other safety protective devices in place and
in good working order .
•Keep bystanders and children out of the operating
area. Never allow children to operate the machine.
•Stop and shut of f the machine and remove the key
before servicing.
•Improperly using or maintaining this machine can
result in injury . T o reduce the potential for injury ,
comply with these safety instructions and always
pay attention to the safety-alert symbol , which
means Caution, W arning, or Danger—personal
safety instruction. Failure to comply with these
instructions may result in personal injury or death.
4

Safety and Instructional Decals
Safety decals and instructions are easily visible to the operator and are located near any area
of potential danger . Replace any decal that is damaged or missing.
decal1 15-7739
1 15-7739
1. Falling, crushing hazard—do not carry passengers.
decal131-8527
131-8527
1. Performance mode
2. Eco mode
200 LBS
91 KG
1500 LBS
680 KG
137-9984
decal137-9984
137-9984
1. Do not exceed a tongue
weight of 91 kg (200 lb).
2. Do not exceed a transport
load of 680 kg (1,500 lb).
decal139-4610
139-4610
1. W arning—read the
Operator ’ s Manual .
2. Crushing hazard, cargo
box—use the prop rod to
support the cargo bed.
decal140-4590
140-4590
1. Read the Operator ’ s Manual for battery information.
decal144-0275
144-0275
1. Batteries are ammable.
5

decal144-0277
144-0277
1. Positive terminal 4. Do not dispose improperly .
2. Read the Operator ’ s
Manual .
5. Do not expose to re.
3. Recycle the battery .
decal145-8016
145-8016
1. Read the Operator ’ s
Manual before performing
maintenance.
4. Brake uid
2. Service interval (hours) 5. Grease points
3. T ransaxle uid
decal145-2263
145-2263
1. Of f 3. T o start the machine: 1) Sit
in the operator's position;
2) Disengage the parking
brake; 3) T urn the key to
the ON position; 4) Press
the accelerator pedal.
2. On 4. T o shut of f the machine:
1) Release the accelerator
pedal; 2) Engage the
parking brake; 3) T urn the
key to the OFF position; 4)
Remove the key .
decal145-7345
145-7345
1. Electrical shock hazard
6

decal147-8205
147-8205
1. 60 V plug
3. Bed lift
2. Electrical power
decal145-5301
145-5301
1. Negative battery terminal
decal145-5338
145-5338
1. W arning—read the Operator ’ s Manual . 4. Electric shock hazard—do not perform maintenance on the
battery .
2. W arning—do not open the battery; do not use a damaged
battery .
5. Electric shock hazard
3. Explosion hazard—do not expose to sparks or open ame.
decal145-2261
145-2261
1. W arning—read the Operator ’ s Manual . 3. Falling hazard; severing hazard of limbs—do not carry
passengers in the bed; do not carry extra passengers in
between the seats; do not put your arms or legs outside of
the machine while operating.
2. W arning—receive proper training before operating the
machine.
4. T ipping hazard—drive slowly across or up slopes; take turns
slowly; do not exceed speeds of 25 kph (16 mph); drive slowly
when hauling cargo; drive slowly on uneven terrain.
7

decal147-8184
147-8184
1. Headlights 6. Main system B+
2. Alarm 7. Display power
3. USB power point
8. Horn
4. Read the Operator's Manual for fuse information.
9. Electrical shock hazard
5. DC to DC converter
8

Setup
Loose Parts
Use the chart below to verify that all parts have been shipped.
Procedure Description
Qty .
Use
Steering wheel
1
Locknut 1
Wheel cover 11
Screw
3
Install the steering wheel (international
models only).
2
No parts required
–
Charge the machine.
3
No parts required
–
Check the uid levels and tire pressure.
4
No parts required
–
Burnish (break-in) the brakes.
Operator's Manual
1
Registration card 1
Predelivery Inspection Form 1
Certicate of Quality
15
Key 2
Read the Operator's Manual and view
the setup material before operating the
machine.
1
Installing the Steering
Wheel
International Models Only
Parts needed for this procedure:
1
Steering wheel
1 Locknut
1 Wheel cover
3
Screw
Procedure
1. Place the steering wheel on the steering shaft.
Ensure that the steering wheel is centered
(i.e., the at bottom should be parallel with the
ground).
2. Use the locknut to secure the steering wheel to
the steering shaft.
3. T orque the locknut to 27 N∙m (20 ft-lb).
g424446
Figure 3
9

4. Use 3 screws to secure the wheel cover to the
steering wheel.
5. T orque the 3 screws to 0.6 N∙m (5 in-lb).
g424447
Figure 4
2
Charging the Machine
No Parts Required
Procedure
Charge the machine; refer to Understanding the
Lithium-Ion Battery Charger ( page 28 ) .
3
Checking the Fluid Levels
and T ire Pressure
No Parts Required
Procedure
1. Check the brake-uid level before you rst start
the machine; refer to Checking the Brake-Fluid
Level ( page 45 ) .
2. Check the transaxle-uid level before you
rst start the machine; refer to Checking the
T ransaxle-Fluid Level ( page 44 ) .
3. Check the air pressure in the tires; refer to
Checking the T ire Pressure ( page 19 ) .
4
Burnishing the Brakes
No Parts Required
Procedure
T o ensure optimum performance of the brake system,
burnish (break-in) the brakes before use.
1. Bring the machine up to full speed, apply the
brakes to rapidly stop the machine without
locking up the tires.
2. Repeat this procedure 10 times, waiting 1 minute
between stops, to avoid overheating the brakes.
Important: This procedure is most effective
if the machine is loaded with 227 kg (500 lb).
5
Reading the Manual and
V iewing the Setup Material
Parts needed for this procedure:
1
Operator's Manual
1 Registration card
1Predelivery Inspection Form
1
Certicate of Quality
2 Key
Procedure
•Read the Operator's Manual .
•Fill out the registration card.
•Complete the Predelivery Inspection Form .
•Review the Certicate of Quality .
10

Product Overview
g319171
Figure 5
1. Hood latch
3. Cargo bed
5. Battery-charger outlet
2. Steering wheel
4. T owing tongue
6. Cargo-bed lever
g319172
Figure 6
1. Passenger handhold 3. T railer hitch
2. Parking-brake lever 4. Rear cargo-bed-accessory mount
1 1

Controls
Control Panel
g435396
Figure 7
1. Horn switch 6. Parking-brake lever
2. Light switch
7. USB power point
3. Display 8. Accelerator pedal
4. Direction selector 9. Brake pedal
5. Key switch
Accelerator Pedal
Use the accelerator pedal ( Figure 7 ) to vary ground
speed of the machine. Pressing down the accelerator
pedal starts the machine. Pressing the pedal farther
increases ground speed. Releasing the pedal slows
the machine, and the machine shuts of f.
The maximum forward speed in performance mode is
26 km/h (16 mph) as shown in Figure 18 .
The maximum forward speed in economy mode is 19
km/h (12 mph) as shown in Figure 18 .
Brake Pedal
Use the brake pedal to stop or slow the machine.
W ARNING
Operating a machine with worn or incorrectly
adjusted brakes can result in personal injury .
If the brake pedal travels within 25 mm (1
inch) of the machine oor board, adjust or
repair the brakes.
12

Parking-Brake Lever
The parking-brake lever is located on the control
panel ( Figure 7 ).
Whenever you shut of f the machine, engage the
parking brake to prevent the machine from accidentally
moving. If the machine is parked on a steep grade,
ensure that you engage the parking brake.
T o engage the parking brake, pull the parking-brake
lever toward you ( Figure 8 ).
g033923
Figure 8
1. Parking-brake lever
T o disengage the parking brake, push down the
button on top of the parking-brake lever , pull the
parking-brake lever toward you to release pressure,
and then push the parking-brake lever forward ( Figure
9).
g033924
Figure 9
1. Parking-brake lever
Direction Selector
The direction selector is located to the left of the
parking-brake lever . The direction selector has 2
positions: F ORWARD and R EVERSE (Figure 7 ).
Important: Always stop the machine before
changing direction.
Horn Switch
The horn switch is located on the control panel ( Figure
7). Press the horn switch to sound the horn.
Light Switch
Use the light switch ( Figure 7 ) to illuminate the
headlights. Push the light switch up to turn on the
headlights. Push the light switch down to turn of f the
lights.
USB Port
Use the USB port ( Figure 7 ) to power mobile devices.
Important: When you are not using the USB port,
insert the rubber plug to prevent damage to the
port.
Key Switch
Use the key switch ( Figure 7 ), to run and shut of f the
machine.
The key switch has 2 positions: O Nand O FF . Rotate
the key clockwise to the O Nposition to operate the
machine. When you stop the machine, rotate the key
counterclockwise to the O FF position to shut of f the
machine. Remove the key whenever you leave the
machine.
13

Display
The display shows information about your machine,
such as the operating status, various diagnostics, and
other information about the machine ( Figure 10 ).
g320256
Figure 10
1. Indicator light 2. Display
There is a startup screen, run screen, and charging
screen on the display ( Figure 1 1 ,Figure 12 , and
Figure 13 ).
Figure 12 shows what you may see on the display
when you run the machine. The startup screen
displays for a few seconds after you turn the key to
the O Nposition, then the run screen displays.
g413507
Figure 1 1
Startup screen
1. Software revision
g413587
Figure 12
Run screen
1. Battery charge 3. Direction
2. Hours operated
14

g413589
Figure 13
Charging screen
1. Battery life 3. Estimated time to fully
charge the machine
2. Battery currently charging
indicator
4. Charging current (Amps)
The run screen with the direction position ( Figure 14 )
appears when you change directions.
g415318
Figure 14
1. F ORWARD position
The run screen with the current machine speed
(Figure 15 ) appears when you are driving the machine.
g415320
Figure 15
1. Current machine speed
An active fault code ( Figure 16 ) appears on the
display if there is an issue with the machine.
g415319
Figure 16
1. Active fault indicator
2. Fault code
15

When the cold battery indicator ( Figure 17 ) appears,
the machine performance changes until the battery
temperature is above 0°C (32°F).
g424100
Figure 17
1. Cold battery indicator
Icon Descriptions
Direction— F ORWARD position
Direction— R EVERSE position
Parking brake is engaged.
Hour meter
Battery voltage
Battery charge level
Battery currently charging
Low-battery advisory
Eco Mode is on.
Active fault
Hot battery indicator—battery
temperature is greater than
67 ° C (152 ° F)
Cold battery indicator—battery
temperature is less than 0 ° C
(32 ° F)
16

Supervisor Speed-Limit Switch
The supervisor speed-limit switch, located under
the seat assembly , has 2 positions: P ERFORMANCE
and E CONOMY . Rotate the switch clockwise to the
ECONOMY position to limit the maximum machine
speed to 19 km/h (12 mph). Rotate the switch
counterclockwise to the P ERFORMANCE position to
restore the maximum speed of the machine to 26 km/h
(16 mph) as shown in Figure 18 .
g319173
Figure 18
1. P ERFORMANCE position
3. Supervisor speed-limit
switch
2. E CONOMY position
Passenger Handholds
The passenger handholds are located on the outside
of each seat ( Figure 19 ).
g033955
Figure 19
Passenger Side Shown
1. Passenger handhold
17

Specications
Note: Specications and design are subject to change without notice.
Base weight
445 kg (980 lb)
Rated capacity (on level ground)
544 kg (1,200 lb) total, including 91 kg (200 lb) operator and 91 kg
(200 lb) passenger , load, accessories, and attachments
Gross vehicle weight (GVW)—on level ground 988 kg (2,180 lb) total, including all of the weights listed above
Maximum cargo capacity (on level ground) 363 kg (800 lb) total, including rear-mounted accessories
Maximum rear cargo bed accessory mount capacity
45 kg (100 lb) total
T ongue weight: 91 kg (200 lb)T ow capacity
Gross trailer weight (GTW): 680 kg (1,500 lb)
Overall width 1 19 cm (47 inches)
Overall length 302 cm (1 19 inches)
Overall height 127.5 cm (50-3/16 inches)
21.6 cm (8-1/2 inches) at the front with no load or operatorGround clearance
14 cm (5-1/2 inch) at the rear with no load or operator
Wheel base
220 cm (86-5/8 inches)
Front: 1 19 cm (47 inches)Wheel tread (center line to center line)
Rear: 1 19 cm (47 inches)
Inside: 102 cm (40 inches)Cargo bed length
Outside: 1 14.3 cm (45 inches)
Inside: 98 cm (38-1/2 inches)Cargo bed width
Outside of the molded fenders: 107.3 cm (42-5/16 inches)
Cargo bed height 28 cm (1 1 inches) inside
Attachments/Accessories
A selection of T oro approved attachments and accessories is available for use with the machine to enhance
and expand its capabilities. Contact your Authorized Service Dealer or authorized T oro distributor or go to
www .T oro.com for a list of all approved attachments and accessories.
T o ensure optimum performance and continued safety certication of the machine, use only genuine T oro
replacement parts and accessories. Replacement parts and accessories made by other manufacturers could be
dangerous, and such use could void the product warranty .
18

Operation
Note: The procedures in this section show a
machine with a plastic cargo bed and bucket seat;
for additional procedures for other attachments,
refer to the Operation section (if applicable) in the
Installation Instructions. V isit www .T oro.com for your
instructions or scan the QR code (if applicable) on
your attachment.
Before Operation
Before Operation Safety
General Safety
•Never allow children or people who are not trained
or physically capable to safely operate or service
the machine. Local regulations may restrict the
age of the operator . The owner is responsible for
training all operators and mechanics.
•Become familiar with the safe operation of the
equipment, operator controls, and safety signs.
•Shut of f the machine, remove the key , and wait
for all movement to stop before you leave the
operator ’ s position. Allow the machine to cool
before adjusting, servicing, cleaning, or storing it.
•Know how to stop and shut of f the machine quickly .
•Ensure that there are not more occupants (you and
your passenger(s)) than the number of handholds
equipped on the machine.
•Check that all safety devices and decals are in
place. Repair or replace all safety devices and
replace all illegible or missing decals. Do not
operate the machine unless they are present and
functioning properly .
Performing Daily
Maintenance
Service Interval : Before each use or daily
Before starting the machine each day , perform the
Each Use/Daily procedures listed in Maintenance
( page 30 ) .
Checking the T ire Pressure
Service Interval : Before each use or daily
Front and rear tires air pressure specication: 165
to 207 kPa (24 to 30 psi)
Important: Do not exceed the maximum air
pressure indicated on the sidewall of the tire.
Note: The air pressure needed in the tires is
determined by the payload that you intend to carry .
1. Check the air pressure in the tires.
•Use lower air pressure in the tires for lighter
payloads, for less soil compaction, for a
smoother ride, and to minimize tire marks on
the ground.
•Use higher air pressure in the tires for
carrying heavier payloads at higher speeds.
2. If necessary , adjust the air pressure in the tires
by adding or removing air in the tires.
g001055
Figure 20
19

Breaking in a New Machine
Service Interval : After the rst 100 hours —Perform
the breaking in a new machine
guidelines.
Perform the breaking in a new machine guidelines
to provide proper performance and long life for the
machine.
•Check the brake uid.
•A void hard braking situations for the rst several
hours of new machine break-in operation. New
brake linings may not be at optimum performance
until several hours of use has caused the brakes
to become burnished (broken-in).
•Refer to Maintenance ( page 30 ) for any special
low hour checks.
•Check the front suspension positioning and adjust
it, if necessary; refer to Adjusting the Wheel
Alignment ( page 42 ) .
•For optimal battery performance and battery life,
perform the following battery break-in process:
1. Charge the batteries to 100% when you
receive your machine.
2. Run the machine until the display shows the
low-battery advisory (approximately 5%),
then fully charge the batteries to 100%.
Repeat this step 4 times to optimize battery
performance.
During Operation
During Operation Safety
General Safety
•The owner/operator can prevent and is responsible
for accidents that may cause personal injury or
property damage.
•Passengers should sit in the designated seating
positions only . Do not carry passengers in the
cargo bed. Keep bystanders and pets away from
the machine during operation.
•W ear appropriate clothing, including eye
protection; long pants; substantial, and
slip-resistant footwear . T ie back long hair and do
not wear loose clothing or loose jewelry .
•Use your full attention while operating the
machine. Do not engage in any activity that
causes distractions; otherwise, injury or property
damage may occur .
•Do not operate the machine while ill, tired, or
under the inuence of alcohol or drugs.
•Do not exceed the maximum gross vehicle weight
(GVW) of the machine.
•Use extra caution when operating, braking, or
turning the machine with a heavy load in the cargo
bed.
•Carrying oversized loads in the cargo bed reduces
the stability of the machine. Do not exceed the
carrying capacity of the bed.
•Carrying material that cannot be bound to the
machine adversely af fects the steering, braking,
and stability of the machine. When you carry
material that cannot be bound to the machine, use
caution when steering or braking.
•Carry a reduced load and reduce the ground
speed of the machine when operating on rough,
uneven terrain, and near curbs, holes, and other
sudden changes in terrain. Loads may shift,
causing the machine to become unstable.
•Before you start the machine, ensure that the
transmission is in neutral, the parking brake is
engaged, and you are in the operating position.
•Y ou and your passengers should remain seated
whenever the machine is moving. Keep your
hands on the steering wheel; your passengers
should use the handholds provided. Keep arms
and legs within the machine body at all times.
•Operate the machine only in good visibility .
W atch for holes, ruts, bumps, rocks, or other
hidden objects. Uneven terrain could overturn the
machine. T all grass can hide obstacles. Use care
20